Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher The lower drawer won't complete a cycle. It will fill and empty 4 or five times in succession then continue to wash for about 15 mins the it starts to fill and empty as before. On a 36 min Eco cycle after 1 hr it still shows to have 15 mins to the end of cycle and wants to run forever. I have swapped the control boards to no avail.

Answers :

\015\012User Manual, above. Below are DIY troubleshooting help sites.\015\012http://www.acmehowto.com/howto/appliance/dishwasher/dishwasher.php\015\012
\015\012 below, are service and repair manuals, below.\015\012http://www.repairclinic.com/Dishwasher-Repair-Help\015\012
\015\012Above are the best DIY help sites, use to troubleshoot.\015\012
\015\012Below BOTH are a generic Service and Repair manual, use this to troubleshoot and repair, your unit. All dishwashers are essentially the same.\015\012http://\015\012
\015\012Below is a Training Service manual, this is what is used to train engineers to service and repair dishwashers.\015\012
\015\012I would think, that you have a sensor problem, please work through the troubleshooting procedures and you should soon track it down and repair it.\015\012However if you want to get an engineer, please contact, a Local F&P office, ask them for a referral, to an Authorised, service center, alway get a "Quote" before proceeding with any repair.
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher The lower drawer won't complete a cycle. It will fill and empty 4 or five times in succession then continue to wash for about 15 mins the it starts to fill and empty as before. On a 36 min Eco cycle after 1 hr it still shows to have 15 mins to the end of cycle and wants to run forever. I have swapped the control boards to no avail.

Http://www.retrevo.com/support/Fisher-&-Paykel-DD603-Dishwashers-manual/id/20093dj878/t/2/\015\012 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a SE24T250 and the timer on the auto programme says 188 mins (it is usually around 120 mins) When the prog runs it doesn't finish and shows 1 minute to go and never gets to the drying or end of cycle part of the programme. Have tried the reset but it still shows 188 mins when complete. Any ideas?

... Siemens Dishwashers

2 years old but NEVER used it yet. Put on today and it would not run any cycles. Let in water and emptied it out but would not do a wash cycle. All this from start to finish in about 8 mins. Washer kept making this droning noise as if it was trying to do something but couldn't. Checked all the waste pipes and filters - all clean - By the way it was still empty of crockery when I tried to do this. Bosch Model SHV55 MO3GB

Dishwasher have a antiflood device system in the base of the applince try a tip the machine backwoord or sideway if water comes out the base you have a leak generally associate wit a failure of the seal around the impeller of the motor or the microsw ... Bosch Dishwashers

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!

This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

Regular cycle took 3 hours then would not shut off. Stopped at 1 min. soapy water still filled the bottom, dishes had soap on them. water finally drained almost out but I am afraid too run another cycle. any ideas? thanks

There is a heating element in the dishwasher that heats the water to about 155F at which point a thermostat closes and sends power to the timer to advance. If the water does not reach this temp, the dishwasher will not advance. Often the problem lies ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.

If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

When ever i start my Hotpoint DWF 35 dish washer the numeric display has started showing a very long cycle time, it seems to be adding about 60 mins on what the cycle normally takes. It still seems to wash ok but takes forever to complete.

... Hotpoint 24 in. DWF35 Built-in Dishwasher

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?

... Dishwashers

Just had new Frigidaire dishwasher installed. When cycle is started, display shows 99. Unit will fill with water, run cycle for about five minutes, stop and empty water then display a flashing PF. Can not seem to find a list of codes for this.

Pf is means power failure. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Dishwasher fills and appears to be going through cleaning cycle ok. However if I open the door part way through the dishes appear as though nothing has happened, dishes are still dry and dirty. have checked hoses, manually added water, observed emptying etc. Any ideas nost welcome, Thank You

Most of the time it's because the impeller assembly has either something stuck in it or has just plain worn out.\015\012Also you want to check and make sure the holes in the washing arms are clear (Poke a little toothpick threw the ... Bosch 22 in. SKT5108 Free-standing Dishwasher

Hi, I have a Neff S5457XOGB dish washer. The unit is programmed to start - but the pump just keeps empying water, even when the door is open. After approx 5 mins this can stop and thedishwasher enters its normal cycle - however there is no water. I have checked and clean the pump assembly I have filled the base with water - and the pump successfully empties the into the drain I have checked the filter that conects directly to the cold feed. - Any advice please? Many thanks.

... Neff 24 in. S5457X0GB Built-in Dishwasher

My dishwasher makes a banging sound, I've checked the arm & even when the washers is empty it still makes that sound. NOW I've ALSO got a sound like a "clothes washer in spin cycle mode" also in the wash mode of my dishwasher. Do I need a service call or should I just replace it since it seems to be falling apart....it's only 2 yrs with min use

Hi,This is quite a common problem. I would be able to help you, if you could provide few more details. When did you hear the banging noise i.e when filling, start of the cycle, mid cycle or it is always there?Thanks!! ... GE 24 in. Profile PDW7800 Built-in Dishwasher

I have a Kenmore Ultra Wash built-in Diswasher. The flap on the detergent door does not open as it should during wash cycle. Also, I thought the rinse aid was empty so I went to fill it and its obvious that it has not been dispensing either. Otherwise the dishwaser seems to work ok, but we have hard water & I've tried everything and still have residue on dishes.

Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

Washer will run for about 3 min. and then just shuts off. Soap is still encased in box on door. No cycles will run for more than 3 minutes. Sometimes it will fill up with water and just shut off. Won't wash at all.

... Maytag 24 in. MDBH940AW Built-in Dishwasher

Bosch type SL1501 dishwasher will fill and empty on reset but will not go onto any cycle, shows "check water" warning light after a minute or so.

... Bosch Dishwashers

I have a Dishlex 100, it seems to fill with water, but then when it fills it just stops. Dosent do anything. It just clicks through the cycle without washing. It then seems to empty out water and refills it to rince but once again dosent actually do anything but click through rinse cycle then clicks along till the emptying out cycle comes up to empty it.

... Dishwashers

Dishwasher fills with water, then empties, fills then empties, and repeats this cycle a few times - then decides to work. then part way through cycle - it repeats this frustrating cycle, making the whole washing use loads more water and take much longer

Hi,\015\012Your dishwasher may pre-heat the water. If so, and if the water entering the dishwasher is cool, the heater may take up to half an hour to heat the water.\015\012To avoid the wait, increase the incoming water temperature before turning on ... Fisher and Paykel DS605I Built-in Dishwasher

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr

WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

FDW60 dishwasher - taken apart pump and that is clear. Seems that dishwasher fills, and empties and heats all OK but water wont go around the machine ie the motor pump doesnt start - any idea how to take this out and replace without having engineer around? Taken small pump apart and its clear. First of all the Eco and fast light flashed, then we took it apart with some direction from online discussion advice. Now Eco and Pre wash lights are flashing. Machine empties water, then fills with

... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?

... Asko 24 in. D3350 Dishwasher

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help

Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

I actually don't know what type of Bosch I have. I know that is a problem, but maybe you can still help. It has a simple panel that says: Pot Scrubber, regular wash, quick wash, rinse and hold. When I turn on quick wash, sometimes it says 38 min. 45 min. 56 min. We want to keep it at 38 minutes and we don't know why it varies. If we have to open it mid-cycle, it switches to a higher cycle time. How do we set it for 38?

On a Bosch dw, it has a light sensor to sense soil in the water.. if the control feels that the water going through the sensor is not clean/ or clean it will add or minus time..one thing you can do is make sure that your drain line from dw to sink dr ... Bosch 24 in. SHU43 Built-in Dishwasher

I've just bought the new LG Direct Drive, the problem is when I put it on ECO cycle it takes 3hrs 28 min to complete a cycle. Is this normal, I was under the impression a cycle should be about 30 min

Make sure that the water inlet pressure is good and there is no restriction ,\012Now it is normal that the wash cycle is long as the dishes are put into and set to be done overnight.\012But it will be good to clarify if the ECO wash take ... LG Dishwashers

Fisher & Paykel single SS Dishdrawer. Cycle's stuck. Normally sticks at 137mins and 33 mins, has stuck on other times too but it's always on those times. Have tried pausing and opeiong the drawer int he hope to kick it back into working but doesn't help. A normal cycle of 151mins is taking 4 hours.rnI normally have to let the cycle run till it sticks on 33 mins then I trun it off letting the dishdrawer empty and kick into dry mode. I hate to see my next electricity bill, its been a month n

My dd603 takes 3 hrs to do a 55 minute cycle-who can help me ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on I bought mine new off the internet and it's been running great for about 2 months. Now I can't get it to drain and E2 shows, I can't get my money back because I've had it more than 30 days, if the solution is a pump, I'm tossing it and getting a good one from

E2 is a hose issue. There is either a kink in the hose, the hose is too high to drain or the pump is faulty.1-800-26 DANBY ... Danby DDW497W 22 in. Countertop Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1574 seconds