Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

Drawer won't open and get beep code 2 short 1 long

\015 Fisher Pykel DD603SS dishwasher\015\012Bottom drawe won't open. When I try to start a new cycle, I get a two short and one long beep code\015

Answers :

The drawer door seal is locked in. This could be either because the controller has lost power or the seal actuator motor is faulty.
\015\012
\015\012You will have to force open the drawer before you can do anything. (Turn off the mains power when you work on the dishwasher)
\015\012
\015\012Let me know if you can handle electric/ mechanical repairs so that I can guide you further. Otherwise you should call a technician. If you are getting beeps then most likely the door seal system is the problem.
\015\012Are you able to use the top drawer?
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Drawer won't open and get beep code 2 short 1 long


The drawer door seal is locked in. This could be either because the controller has lost power or the seal actuator motor is faulty.\015\012\015\012You will have to force open the drawer before you can do anything. (Turn off the mains powe ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi My F&P dishdrawer flooded. Dried it all out etc, the top drawer doesn't complete the cycle and it beeps continually even when it's not running. I am wondering if I can reset the drawer using the front buttons to get it back to factory default. Bottom drawer works fine. There is no error code on the screen only the lock icon which won't go away. Any ideas?


Not sure if you tried turning the power off at the main switch. Lock icon can gone away if you press the necessary keys as shown in the user guide. Also the sequence of keys to press for getting factory defaults of different options is also in the us ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Whirlpool adg4760 beep code...3 short beeps 1 long beep


... Whirlpool Dishwashers

The door wont stay shut on frigidaire 4300. I have cleaned all around including gasket. Halfway through the wash cycle, cycle stops and we get CL code for open door. If we push on door, it goes for another few minutes.


Something is wrong with the door latch. Replace or make adjustment. ... Frigidaire Dishwashers

I am getting a flood switch activation code on my Kitchenaid kudd01dppa. The pump on the top and bottom drawer keeps running and they continuously beep with the rinse light on.


... Dishwashers

Getting and F1 code on both drawers and a beeping sound


That is the code for water in the drain pan. If you access the bottom pan you will notice water in it. This happens when the lid does not seal properly usually. Check the lid seals and also listen to the acuator motors to see if they are straining. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

When I press start I get a double beep sound and dishwasher wont go. There are no other codes or anything. Its an Lg ld1204mi dishwasher


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

Kitchenaid kuddo1dppa I own a KitchenAid KUDD01DPPA, 2 drawer dishwasher. I am not a technician, however I have had a lot of experience in repairing various appliances and am savvy with electronics and mechanical technical issues. Here's the problem: I was getting rinse error codes in both drawers, pulled the bottom drawer out, removed the cover to the circuit board and used a dryer to dry up the moisture on the flood switch. Now I am getting Fill Failure error code on both drawers. I have g


Test this steps and fix it. God bless you\012 \012 Water Inlet Valve\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

Drawers Stuck I've had my dishwasher for a couple of years now. All of the sudden the drawers are extremely difficult to open. I have to use all my strength to pry open the drawers so I can get the dishes out.  It started out as only the bottom drawer having the problem and now both drawers are having it.  It seems to be running fine because the dishes that were in the drawer before it got stuck were cleaned.  And there is nothing blocking the drawer from opening.  It seems like the seal that c


I turned off the electrical breaker for about 8 seconds and it rebooted itself ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on I bought mine new off the internet and it's been running great for about 2 months. Now I can't get it to drain and E2 shows, I can't get my money back because I've had it more than 30 days, if the solution is a pump, I'm tossing it and getting a good one from


E2 is a hose issue. There is either a kink in the hose, the hose is too high to drain or the pump is faulty.1-800-26 DANBY ... Danby DDW497W 22 in. Countertop Dishwasher

Fisher & Paykel dishwasher drawer won't run, beeps F2 error code


Craig, we had virtually the same situation.  The repair man  came and it took 2 minutes to fix.  The problem was that the bottom drawer had not been used for a couple of years and thus the impellor had jammed.  to fix it take out ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Fphd2481kf control won't reposed. I unplugged it for a few hours to get it to reset. When plugged back in the pf code was shown. I opened and shut door to clear code. U cannot get it to respond to any input and it doesn't show any codes.


... Frigidaire FPHD2481KF Builtin Dishwasher

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

One of the lid actuator motors died on my F&P DD603 dishwasher and was replaced by the serviceman. He put the machine in a test mode and pressed a code to try the operation while the drawer was open. I witnessed the lid closing properly. Now it appears that the other actuator is faulty. To save an extremely expensive service call, how can I put the machine in test mode and verify the actuator operation with the drawer open?


To test the lid operation first pull the drawer forward of the cabinet\015\012by depressing the lugs on each side rail and pulling the drawer\015\012forward. Then go into diagnostic mode. Once there press power once and\015\012the lcd will display "H ... Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

My fisher dd6031 bottom drawer doesn't seem to get rid of all the water,,and it keeps beeping and will keep beeping through the night if you don't catch it...we have been putting it through another rinse cycle to get rid of the water....can you help? Thanks, Maria


You will have to take the filter plate out the motor rotor out. Then clean the rotor cavity and replace in reverse order.\015\012\015\012Are you getting any error codes?\015\012Does the beeping stop if you turn the power off and on? ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Dishwasher not getting enough water in either drawer, although top drawer gets more. Dishwasher keeps beeping during cycle and reads not enough water and then stops running until you press the start button. Need Help, any ideas?


This sounds like a hard water deposit problem.Check your water inlet valve for a screen and see if its clogged. Also it may just be a water valve/solenoid problem. As in, it's too crusted up to float up and down.Some models have a water f ... Fisher and Paykel DD605FD Stainless Steel Built-in Dishwasher

My bosch dishwasher wont dry. The model number is she44c02uc/47. I don't know what codes i need to see to get it to heat. I've tried to hold the cancel drain buttons in to change the code. I get a C1. what does that mean. Thanks for your help. john


... Bosch Dishwashers

Hi, I have a Fisher and Paykel DD603 dishwasher. The bottom drawer works fine but the top drawer doesnt work at all. It appears normal until the start button is pushed and then I get 3 very quick beeps followed but a 4th slightly longer beep. Then nothing happens, any ideas or help would be much appreciated. Thanks Neville.


... Fisher and Paykel 24 in. DD603MFC Built-In Dishwasher

Hi Have a built in AEG OKO Favorit slim dishwasher (can't find exact model no). Problem is that dishwasher tablet dispenser does't open and after 5 minutes get 5 lots of 2 beeps. When I open the dishwasher, the Rinse/Hold, Intensive, and Normal lights are all flashing. Do I need to get an engineer out? Thanks


HI there,If that\015\012lever is broken or in some way defective, it will need to be replaced. As well as controlling cycle times, the timer on many\015\012dishwashers also functions as an actuator for the spring-loaded\015\0 ... Dishwashers

Intermitttent beeping on bottom drawer of dish washer no error code only cycle to work all the way through is rinse cycle. Have turned off power supply over night did not fix problem. When you press pause button restarts for about five minutes then beeps again. No problem with top drawer. All inside cleaned using correct powder and rinse aid.


Panel control board Call Encompass Parts 1-800-638-3328 ... Fisher Dishwashers

My Fisher and paykel dishwasher drawers are showing a F1 fault on the top drawer screen, But it was the bottom drawer that was in use at the time of the fault occured. The top drawer will open but the bottom drawer is locked. I need to unlock this drawer to get my cooking equpiment out. Please Help. I know that the F1 fault is a flood fault but how do fix it.


... Fisher and Paykel Dishwashers

Fisher & Paykel 2 drawer dishwasher: I too cannot get power to top drawer. 4 days ago we had an F1 code. My husband pulled out drawer, wiped up water, and dried it out. Put it back in overnight, and both drawers worked fine. Now the bottom drawer is okay, but no power to top. Help!


He might have unplugged something in the proccess of drying the bottom ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi, I have a fisher and Paykel double dish drawer model DD605. A couple of days ago when we opened the top drawer all the lights flashed and beeped in sequence repeatedly and would only stop when the power was turned off or the dishdrawer closed. Today I went to turn the top dish drawer on and cannot change the cycle off rinse. I can push the eco button and the rinse cycle works no problem but I cannot change the cycle. The bottom drawer is running as I write this and appears to be fine. An


Hi\015\012\015\012\015\012Could you please let me know which all lights are blinking/lit solid in sequence from right to left. This could be an issue of drawer lock mechanism or flood switch issue. PLease post back with detai ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1030 seconds