Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

When running one draw water collects in unused drawer

\015 We have had continueous problems with water collecting in the drawer that isn't being used after the other drawer. We keep having people come out and they find a lemon seed or something tiny in the wire catch basket and say that is the problem, but after a few day's of using it the problem happens again. One thing I should mention is that we do not have an air gap . We were told when we bought this dishwasher that this was one of the few dishwashers out there where an airgap wasn't required.\015\012\015\012Thanks, Patricia\015

Answers :

I would recommend that you check the dishwasher installation instructions to check if the water inlet and outlet are properly set up. Look at page 4.
\015\012
\015\012If this is happening only with bottom drawer after top drawer is run, then it could be a leaking door seal. But if it happens with both drawers, then it is a bit un usual and could be due to a backflow in the drain hose.
\015\012
\015\012If you are using inskerator in the sink, then make sure it is not filled up.
\015\012
\015\012Hope this helps.
\015\012
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When running one draw water collects in unused drawer


I would recommend that you check the dishwasher installation instructions to check if the water inlet and outlet are pro ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Our Hotpoint Dishwasher Model HDA200X-73BA has two little white plastic pipe stubs poking out of the bottom of the dishwasher. During one of the cycles--(I don't think it is the drain cycle)-- some water is being released from one of these pipe stubs and then it stops and the other one runs some water. They each only run for a few seconds, but the water is just running on the floor. These little pipe stubs are about one half inch in diameter and project out of the bottom of the dishwasher about


Hello. go to the sears direct website, click on the blue link below, and enter your model number. ou can then access an excellent parts diagram which will show these stubs and what may be missing from them. Joe\015\012\015\012 ... Hotpoint Dishwashers

I have the two drawer dishwasher. It's about 10 years old. The top drawer continues to work OK but for the last three attempts when I run the bottom drawer water gets out into the drip pan below and gives the F1 signal. I can dry the drip pan out and clear the F1 signal so the top drawer works. But running the bottom drawer causes water to leak again with the resultant F1 signal. There is very little water in the bottom drawer (just a little in the filter bowl) so I think the pump is pumping


Hi,Unless you keep using the wrong detergent or keep putting dishes that \015\012are to tall in there. i would have to say your actuators ar bad and its \015\012not letting the lid go down to seal it all the time.There is no adjustment. Y ... Fisher and Paykel Dishwashers

Water backs up into upper drawer when lower draw is run


Make sure hoses arent blocked from bottom drawer. if they not blocked change the check valve in the hose. its under the dishwasher drawer pull the drain hose off the drawer. a small rubber check valve is there ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

My whirlpool gold dishwasher leaves a thick white residue on the dishes. You can actually draw in the residue with your finger. I have cut back on soap, tried different soap, and run vinegar thru it. Nothing helps. My old dishwasher ran fine. Is it because the new one doesn't use as much water? HELP!


Www.dishwasherfilter.com will solve this problem guaranteed. ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

No water I have the kenmore ultra wash quiet guard built in. You can hear the motor running but it is not drawing water into the machine. I have checked all of the hoses and connections and they are good....pump sounds like its running but just wont draw the water in.


Inlet solenoid not working, check wiring is attached ... Kenmore 24 in. 15932 Built-in Dishwasher

One drawer drains into the other and vice versa


Just cvomes down to the position of the drain hoses, follw the install instructions to the letter. The hoses have to be positioned as per the diagram with the elbow supplied. ... Dishwashers

Im replacing a frigidaire with a whirlpool and the problem I'm having is the electrical connections. My old Dw had two elec cords running to it. One small one that runs in the same direction as the drain and water hose runs the other is a slightly bigger elec cord that runs straight out the back of the cabinet unit and I cant tell where it goes. But it has on it anaconda w dutrax type nm 12/2 with grounding 600 volts.Do I need both elec cords for the new whirlpool or just one? All the online vid


Hello. Older houses offer all kinds of challenges. In the long run though, that is part of the joy of life. \015\012\015\012You need three things to hook up a typical dishwasher:\015\0121. The hot water source which goes to fee ... Dishwashers

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Fisher and Paykel Dishwasher, bottom drawer gets water in it. This drawer is seldom used and when used the water empties completely. However, it always has water standing in it. I run the rinse cycle and it gets all the water out but after time the water is back. It is enough to cover the large removable metal cover.


... Fisher and Paykel Dishwashers

The dishwasher top drawer is leaking all over the floor during the cycle. When the top drawer is running, It fills up the the bottom of bottom drawer with water also and then neither drawer drains completely. The water is a light brown color after a wash and often half the soap is left in the dispenser.


Fisher and Paykel design a air gap kit to prevent the water back flowing to the other while one is running. it really works and worth of your money.\015\012You need to change the lid seal and a pair of actuators from the top drawer. Because of the ... Fisher and Paykel DD605SS Stainless Steel Dishwasher

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

We just purchased a used Fisher and Paykel DS 603-i. After installing and running the normal cycle there was a lot of water left on the bottom of each drawer. We ran the bottom drawer (water stil siiting on the bottom of the top drawer) and part way through the main wash cycle we got what I think was a F1 error code (we do not have the LCD version but the Rinse light was activated). I took out the bottom drawer, dried out the basin and then took out the washer and reattached the drainage pipes t


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You’ll need to reset it by poweri ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

My Frididaire Dishwasher Model FDB1250REC1 is discolored inside. Its a browninsh color and it has gotten on my Corningware dishes and stained some of them. I can get most of the color off the dishes if I scrub hard. I have run cleaners for the dishwasher thru and cleaned it temporarly. Do you think this is the soap I use, amount of soap or maybe the water. Not sure its the water cause there is another one on my water line that is not really having this problem. I always run hot water just before


So you need to install a water filter, before you connect water supplie, then you need a special soap to clean wachine (Calgonit diswasher cleaner powder ) use-it without dishes. then use a dishwasher salt (to disolve all water dirt and colour) and r ... Dishwashers

Fisher paykel Hi I have a fisher paykel dd603 dishwasher. when I run the bottom drawer on its own ,,it also fill the top drawer with water ! so after the dishwashing cycle , im left with water in the top drawer. im guessing that a valve should close on the top drawer to stop this happening? is there a part I could order and replace myself? thanks [email protected]


Check your email ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

The dishes are not clean when we run the wash cycle. It looks like the water flow from the top sprayer is NOT working. The door, when we open it, has undesolved soap stuck in globs on the top of the door. The top dishes are not clean and some of the botom dishes are not clean. We've run some clear washes to see if we can find the problem. The water flow looks suspect. Is it in the electronics or in the water mechanics. I called the repair guy who ususally comes out and says buy a new one! The re


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... LG 24 in. LDS 5811 Built-in Dishwasher

The dishwasher doesn't seem to have nearly enough water in it. The upper sprayer arm doesn't seem to be spinning when running (I open the door and look really quick) and the lower one looks like it barely spins and barely sprays water. The dishes are barely wet and the soap is just laying on the bottom. The water is on, there are no kinks in the supply line. It sounds like it is running, and pumps pumping, but being brand new I am not sure what it should sound like. It certainly doesn't sound li


I would lift the drain pipe higher. approx. 1/2 the height of the dishwasher . also rechack incomming water supply. Make sure no blockages and the like. Try again. ... Bosch Dishwashers

No water my kenmore ultra wash was unused for two weeks during a renovation and once hooked back up does not allow water to enter the dishwasher. The hose has been checked and runs freely. The dishwasher runs thorugh the cycles but not with any water. Thoughts?


Two things to check. First see if anything is holding up the float inside the tub. Located on the bottom right if I remember correctly. I had a fork fall off the rack and do the exact same thing by getting lodged under the float. Second, if there ... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

NEFF S4443 top spray bar not rotating, no water. Bottom spray bar rotates and sprays water. Checked and replaced fine/course mesh filters. Will pump to empty and refill on pre-wash (rinse). Seems the pump may have two outlets one feeding the bottom spay bar (nearest from of machine) and one just behind which feeds the upper spray bar. Running without spar bars attached (including mechanism feeding to bar, water is only being forced out of the from outlet. Any ideas before I start taking it apart


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

After cycle completed, opened door and found water did not drain. i removed the screen at the bottom and used wetvac to **** all the water out. i was also able to hear suction from hose to sink P trap. i'm confident there is no blockage. i attempted to run again only to find out the pump was running but, no water was filling the machine. Yes! the valves are open! two different issues? one other thing; due to the no thought behind this, the name plate was stuck to the inner part of the door whi


Possible that the drain pump needs a closer look , clean and check if the pump is working. If there is voltage to the pump during the drian then the pump is faulty.\012The second issue if the inlet chocking , check the inlet filter , check the ... Bosch SHU9915UC Dishwasher

I have a F&P Model DD602I. I had a repairman out to change out hoses that were bad and now I have this problem: When I just run the bottom unit, it works fine, but a bunch of water ends up in the top unit that I have to drain out. If I just run the top unit, water collects in that unit causing a default. Now if I run both units together and I start the top unit about 3 seconds after starting the bottom unit, both units work fine! When I look at the hoses under the sink, they loop down quite a bi


Try to isolate the drain hose of the top drawer by disconnecting from the U hose. Run the bottom drawer. \015\012\015\012Similarly isolate bottom drawer and then run top drawer.\015\012\015\012See if problem is linked to back ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

I have the two drawer model dish-drawer system. In the past the top seal leaked and since has been replaced with a new seal. Worked well for several years after but then the top drawer quit running. So we started to use the bottom drawer. That was fine for awhile althought it would pump waste water into the top drawer. Now neither drawer will work. The bottom drawer starts up and shuts down. I pulled the lower drawer and it is dry.


If your model has got an LCD display are you able to record what shows up on the display when the bottom drawer shuts down. If no display then are you able to note down the LEDs which are on inside the top of the drawer lid. It is likely there is no ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Top drawer of dishwaser has standing water when bottom runs


... KitchenAid KUDH03DT Dishwasher

The top drawer started getting very loud - maybe the water pump? Now it looks as if no water is getting into the drawer so dishes remain dirty. The bottom works fine, and is not loud when running.


Yes it is likely the pump rotor is seized. I am assuming the water goes in to the drawer but does not get moved around by the washer arm. This i ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1524 seconds