Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

The top drawer will not take in water. The tap symbol flashes. The bottom drawer is working perfectly. I have cleaned and checked it - no obvious obstruction in the drawer.


Answers :

1 the inlet valve need replacing its bottom of the draw bit tricky to replace it to check it just unclip bottom draw to the side disconect the hose from the inlet top draw valve and turn it on for a sec see if water pumps out make sure you got small bucket if that works finne. 2 its the pump under neath the dish draw thats very tricky took me 1 hour to do
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The top drawer will not take in water. The tap symbol flashes. The bottom drawer is working perfectly. I have cleaned and checked it - no obvious obstruction in the drawer.


1 the inlet valve need replacing its bottom of the draw bit tricky to replace it to check it just unclip bottom draw to the side disconect the hose from the inlet top draw valve and turn it on for a sec see if water pumps out make sure you got small ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have the double drawer dishwasher. It is 3 years old. For about 1 year now one of the programmes - the second one along which is for quite dirty crockery and cutlery (programme is about 99 minutes) - STOPS after about 60 minutes. It bleeps and flashes and the pot wash programme and eco button are on when I open the drawer. Sometimes the programme works right through. No pattern or consistency. Also the dishwasher isn't cleaning terribly well. I've checked the filters as much as I can an


A few things you could do.\015\012\015\012Is this happening with both drawers.\015\012\015\012Take a clean damp cloth and wipe the switches and the inside panel.\015\012\015\012Get a couple of Finish dishwasher cle ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

On an AEG Favorit 64570 VI we have an error 20. Manual indicates a drainage problem, however when we pour in water, it gets pumped out without a problem. No obstructing in the exhaust tube. Next we checked the pressure sensor, by taking it out and blowing into it. It clicked as pressure was applied to it, so the inner switch worked. Everything is clean, but still we get an error 20. What does seem strange is that the appliance does not take in water. Any suggestions are welcome.


... AEG 23 in. Favorit 86070Vi Built-In Dishwasher

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

Previous wash cycle worked perfectly. Next morning , dished not washed. Water pressure is insufficient to spray. Checked sprayers and clean. Removed bottom sprayer arm and tested. Water flows barely. Water fills but pressure insufficient to spray. Actually 'bursts' slightly on shutoff. All other functions work perfectly.


... Kenmore 16872 Built-in Dishwasher

My Miele Platnum dishwasher is not working. It is flashing "intake/drain" When it begins instead of the normal hearing of water moving around you just hear a humming. My husband and father took out all the filters/baskets etc and made sure everything was cleaned out. They checked the hoses. After that it seemed like it was going to work because it started to cycle normally but now it is flashing again and this time there was water standing in the bottom of the dishwasher. Any thoughts?


Most common faults with dishwashers is a drain fault. Check for any kinked hoses and check the drain spigot under the sink where the drain hose connects into the u bend. Usually this is where food gets trapped due to the spigot not being drille ... Miele 23 in. Novotronic G841 Built-In Dishwasher

I have a GLD 4456R00CS dishwasher that is maybe 6 months old. It seems to cycle properly, but has never really cleaned the dishes. This is the worst dishwasher we've ever had (over 25 years) and I'm ready to take it to the street. I've cleaned the screen (was already clean), checked the spray bars for clogs (removed, sprayed water through it, and replaced), and looked for any other obvious problem.


Sorry you have had so much problems with this dishwasher. Before you "take it to the street" please check one more thing. I have had so many people say similar problems. \012\012\012\012Check that you are usin ... GE GLD4456RCS Builtin Dishwasher

My frigidaire dishwasher (FFBD2405KB) is not working... when I press the wash button, it will blink, but nothing happens. I've tried it on all settings, but nothing works. It's obviously getting power since the lights are working. I've cleaned the drain thoroughly and made sure there were no obstructions. Any ideas?


... Frigidaire Dishwashers

Hotpoint dishwasher BFV620 lights 2 and 4 flashing and will not complete a cycle. Dishwasher has been working ok but suddenly stopped and lights 2 and 4 flashing. Checked obvious blocked filter and kinked pipe etc,


... HP Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

We are getting a grit on the dishes on the top rack. We have done many things to solve the problem. Running tang crystles, runing CLR through it, taking it apart to check for blockages, checking the impeller on the pump, blowing comprssed air through it, scrubbing the inside many times. The funny thing is it only happens about every third wash cycle or so. The upper spray arm is free with no obstruction. The dishes on the bottom rack are clean. We use Electosol and jet dry. Our water is softened


Hello John\015\012\015\012Thanks for all the detail. It's far more than I usually get to start with, but please could you also answer the following quick questions:\015\012\015\012- Are the particles hard and gritty or is it f ... Asko Dishwashers

Dishwasher fdw60g fault lights i have the eco and prewash light flashing. i know that this means the filter is blocked. i have cleaned the filters and checked the hoses for blockages and they are all clear and kink free. i have tipped the machine on its side and checked the pump , which is clear aswel. i dont know what to try next to get the machine working and the lights to stop. thanks


... Dishwashers

Fisher & Paykel DW60. Fault: Will not start regardless of program selected. E.g. if "heavy duty" pressed, only light will flash, if "normal" is pressed, only this light will flash etc. All hoses (water and drain) have been checked and no crimps or blockages found at either end. All usual methods tried (e.g. cleaning strainers and filters, turning power off for a while etc). Finally, while lights are working, the machine makes no noise at all when a pogram is selected.


... Dishwashers

I got this dishwasher from a friend that had mice chew the hoses and i was told that it worked perfect before the mice chewed it. I replaced the drain and fill hoses plus the power cord. when i put everything back together and power on I get F1 on the top drawer and the rotor rotates and the heater plate turns on. The botton drawer does nothing with no display. I checked all the wires with a meter and found good continuity thru every pin. I replaced the main filter board. I even switched the


Did the F1 error in the top drawer disappear after you replaced the mains filter board? ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

The water is not draining from machine, although the pump is obviously trying. It doesn't sound quite right. Kind of a growling noise. It can pump water into tubs when experimenting with ideas, but can't pump hard enough to pump the water into the sink. This is all done with the hose removed so we could check for debris in the line. I've checked the filters and they are clean and clear. This is a used machine a friend gave me, and it's been working beautifully until now.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bosch 24 in. SMU40 Built-in Dishwasher

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

Whirlpool DU1145XTPQ dishwasher clean light is flashing. We cannot stop the flashing and the dishwasher will not work. The book says it is the heater circuit. What should we check? What is the most likely problem?


... Dishwashers

Dishwasher will not start. Clean light flashes. Time display shows --. Manual states "The diswasher has malfunctioned". (Obviously) "Call for service to check heater circuit". Will replacing the circuit board solve the problem?


Hello, welcome to FixYa.\015\012\015\012I understand how vague those manuals can be, very frustrating.\015\012\015\012In regards to the fault, while the control can be an issue and ultimately require replacement...that is a wo ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Whirlpool dwh b10.yesterday had problem with water not going anywhere,had to bail it out.today cleaned all filters,now can hear pump working but doesnt appear to be taking water in.i press start button for two seconds,re-programme,and it does the above.then start button flashes and there is a continual beep the programme indicator changes from a wash to rinse during this process.any help ? thanks pete.


... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

I have a Whirlpool Dishwasher DU1345XTVB about 5 years old. It functions perfectly but is not cleaning the dishes well particularly the top rack. The arms spin, soap dispenser works, cycles properly--just doesn't get the food off. I checked the arms to see if the are blocked but don't appear to be as the dishes get wet. Thanks


There are a few things to do. The water temperature is a big contributor, in dishes not getting clean. Another is the type of detergent being used. Liquid dishwasher detergent with water softeners and a drying agent will help loosen food too. If ... Dishwashers

Own a Kenmore 665 dishwasher. The clean light is flashing (7 times) and the machine won't run. Have pulled the control panel and checked the door latch switches and they appear fine. No obvious burned wires any where. Any ideas on what this could be? thanks


It sensed a problem in the heater circuit. try this sequence to reset the code. If it comes back again you will have to determine a cause.The reset sequence used was reported to be the following:\015\0121) Crack the door open. ... Kenmore Dishwashers

After wash cycles are completed there is about 1/2 gallon of water remaining in the bottom of the washer. I checked the drain that exits into a disposal and that is clear. All around the bottom of the washer base is clean and I can find no obstruction. Nothing in the owners manual gives me a clue as what else to do. I don't want to start taking things apart unless I have to.


Hi and welcome to FixYa. I am Kelly. Most dishwashers are connected to the sink / garbage disposal via an Air Gap. The Air Gap gets debris inside it that blocks the drain passages. Check out this video on how to clean it: ... Maytag 24 in. MDBH950AW Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1725 seconds