Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Answers :

Hi
\015\012\015\012


\015\012Thanks for using FixYa.
F1\015\012error means that the flood switch has been activated. You'll need to reset it by powering off the\015\012breaker or by unplugging the unit from the power socket and mains for more than\015\012five minutes. Please check that there is no blockage in the drain hose and it\015\012is not raised higher otherwise the water will run back to the dishwasher. Also\015\012perform the following procedure---
\015\012\015\012

    \015\012 \015\012
      \015\012 \015\012
    • Unplug power and\015\012 remove bottom dish drawer
    • \015\012 \015\012
    • Use\015\012 a Sponge and dry all the excess water underneath
    • \015\012 \015\012
    • Remove\015\012 circuit board cover
    • \015\012 \015\012
    • Dry\015\012 all around and underneath as much as possible
    • \015\012 \015\012
    • Apply\015\012 hairdryer for 10-15min
    • \015\012
    \015\012
\015\012\015\012

Please rate the solution if the issue is resolved or\015\012else revert for further assistance.
\015\012\015\012


\015\012\015\012

Thanks
\015\012\015\012

Rylee

Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Leaking dishwasher There is standing water in the dishwasher when it's not being used. Recently we had a garbage disposal installed and was wondering whether this may cause the water from the sink to settle in the dishwasher. Also, the water rises and leaks on the floor. We have to run a wash cycle to drain and dry out the dishwasher. What do you think the problem is?


It sound like while the assembly of the garbage disposal, you placed the end of the drain line pipe in a lower position than it was before.\015\012Good luck! ... Kenmore 15129 Built-in Dishwasher

The water is pumped out after the rinse cycle then it continues to run and make an unusual noise but nothing happens. The noise is almost a grinding sound. There is also a smell like some part may be hot or the wiring may be hot. I can reset the dishwasher and re-run the cycle up until that same point and it does the same thing again. I have had a repairman out twice in the last six months. The first time he could find nothing wrong because the problem was intermittent and he couldn't see anythi


Timer \015\012\015\012or\015\012\015\012 ... Bosch Dishwashers

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

This problem is intermitten. Kenmore 665 16765690. starting the dishwasher, I hear a motor running. I think it is trying to empty water, however there isn't any water. I will turn the time rotor around to the start again. Sometimes, when I do this the motor running sound has stopped and I hear gurgling sound of water entering. Once this happens, the cycle is good and does well. However, there are times, rotation the timer back to the beginning may take several times, up to about 20 times.


Hiclean water filterthe presure is to lowPls vote me to keep us alive ... Kenmore Dishwashers

I have no power to the dishwasher. I tried the circuit breaker, flipped it. No lights on, nothing. It must have been running when the power might have gone off, may be the power surged or something and it wasn't able to finish running the cycle. I have taken out all my dishes and washed them by hand but I still have water standing in the bottom of the dishwasher. I am a mechanically challenged mom and my husband won't be getting home for two more weeks. The dishwasher is a WhirlPool Gold Quiet


First check and make sure that the units not on a switched receptacle(and is wired into this circuit(i know the dishwasher is "hard-wired",as in the unit doesn't have a plug on it,but it could have been wired into this switched circuit by mistake) un ... Whirlpool Dishwashers

We have a KitchenAid dishwasher (KUDI01FLSS6) which has not been working properly for a long time. We have the dreaded green blinking light mystery. We understand that this could indicate several different problems. We have found that if we run the sink water until it is hot, then start the dishwasher, and then after ten minutes we open then shut the door, it will consistently run the full cycle perfectly. Does this give you any hint of what might be the problem component -sensor, element, the


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Incomplete cycle My Miele dishwasher (3 to 4 years old) finishes, leaving the dishes dirty and wet. It seems that it may only be running through part of the cycle - I'm not sure but from the time I set it going to the time it switches off, it seems shorter than usual. The dishwasher is not emptying as it has a pool of water in the bottom. I have tried various settings and have the same problem. the inlet/drain light DOES NOT come on. I have soaked up all the residue on the bottom and cleaned out


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

The dishwasher appears to be running properly, but in stopping it during a cycle there is no sign of water. Would having hard water, yet a water softener that is need of salt have anything to do with this?


In which cycle you have stopped? Dry cycle!! ... Hotpoint 24 in. HDA3230Z Built-in Dishwasher

My dishwasher is 6 years old it started making clicking and knocking sounds about a week ago. The display is blinking crazy at about 37 minutes left in washing cylce it blinks 37, HO, and CL. It blinks other numbers also. The water still seems to be flowing in and out fine. It's heating up and draining when canceled. I'm running it on normal wash and high temp. cycle. It sounds like the sensing parts in the door are going off and on.


... Frigidaire 24 in. PLDS9999CC Stainless Steel Built-in Dishwasher

Our Hotpoint Dishwasher Model HDA200X-73BA has two little white plastic pipe stubs poking out of the bottom of the dishwasher. During one of the cycles--(I don't think it is the drain cycle)-- some water is being released from one of these pipe stubs and then it stops and the other one runs some water. They each only run for a few seconds, but the water is just running on the floor. These little pipe stubs are about one half inch in diameter and project out of the bottom of the dishwasher about


Hello. go to the sears direct website, click on the blue link below, and enter your model number. ou can then access an excellent parts diagram which will show these stubs and what may be missing from them. Joe\015\012\015\012 ... Hotpoint Dishwashers

When the water cycle is running there is a white plug by the water inlet that is leaking. When the dishwasher is not in the water cycle it does not leak. When the dishwasher is stopped in the middle of the wash cycle and water in in the bottom of the pan it does not leak. It only leaks when the water is running.


Crack in water inlet valve or a pin hole in the hose going from the valve to side of tub spraying water where you see it. You have a holein someting. You need to trace it back to its sourse. When you say "water is running"im guessing thats when its f ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

The dishwasher will start to cycle. I can hear the water begin to run. I hear a click and at the time the dishwasher should start to run the cleaning cycle. During the cleaning cycle the dishwasher will stop working. The dishwasher is silent. The timer will continue and the water will drain out at the appropriate time.


This is probably okay, you have clock like motions running the motor electric contacts. There needs to be a delay between some cycles or shorting will occur. The motor on some designs, for example. is reversed to pump out water. to have this work lon ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher

Maytag dishwasher model MDB7609AWW2 has a blinking clean light. I followed the advice on fixya (thankya!) and by alternating the normal and heated wash buttons I was able to return the lights to normal. However, once I tried to run a normal cycle, it didn't do anything other than fill and drain. I then ran the hot water faucet in the sink until hot and tried another new cycle, but no luck. Any advice is MUCH appreciated!


... Dishwashers

MAYTAG JET CLEAN DISHWASHER MODEL # MDB7100AWB, WILL NOT RUN THROUGH CLEANING CYCLES, TRICKLES WATER UP FRONT DRAINS VERY BRIEFLY, REPEATS THIS FOR A PERIOD NEVER KICKS INTO THE WASH CYCLE, THEN COMES UP BLINKING CLEAN/FINISHED?


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Maytag MDB7100AWB Dishwasher

ASKO 1595 daer greendude, indeed your troubleshooting was right!!!! i pulled out the dishwasher and the base was full of water. once i got water out, the fault sign went away and it's ready to run its normal cycle. now i need to figure out where the leak comes from: either the fitting or the valve itself. just in case i have to replace the valve: any good source to get it from? i live in california. once again, thank you much!!! i'll keep you posted on the developments


I live in australia our part no is 8052120 ... Asko D1776 Stainless Steel Built-in Dishwasher

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a bosch millennium series SHU9905UC. There is still water at the bottom of the dishwasher from the last time it was run. I think it may not have completed the cycle as a few bowls were still dirty. Now when I try to put the washer on and press a cycle, no light is coming on at all. It seems dead. Is there anything I can try before calling in service people?


... Dishwashers

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2462 seconds