Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

Top drawer leaks onto floor. bottom drawer works ok.


Answers :

Looks like you were being helped by another consultant. Unfortunately I do not have access to what solutions were suggested. But reading in between the lines it appears you are checking if the lid seal is moving correctly.
\015\012
\015\012It is unlikely the lid seal motors would be a problem otherwise water would be coming out from everywhere and get to the bottom of the housing and causing the flood switch alarm to trigger.
\015\012
\015\012It might be the lid seal itself that may have been damaged or skewed in the front causing water to leak in the front of the drawer down to the floor.
\015\012
\015\012When you run the diagnostic LD check if rubber seal is coming down from the top inside of the housing. It is meant to seal the top edge of the drawer. The drawer should be open position at that time. - I think you have already taken it out.
\015\012
\015\012If the seal is damaged you will have to replace it.
\015\012The part looks like this. I would not recommend that you replace it yourself unless you are very comfortable with repairing appliances with motors and mechanical precision.
\015\012
\015\012If you are happy with the suggestions then please accept my solution otherwise post a comment so that I can try and help. cmmiuser01.

Hi
\015\012\015\012


\015\012Thanks for using FixYa.
As the bottom drawer is fine the issue is with the\015\012right actuator that has gone bad and so causing the leak. As they come in pair\015\012so both of them should be replaced. Also I'll recommend you to inspect the lid\015\012area including the rubber seal around the top lid, if that's bad you need to\015\012replace that as well. Please accept the solution if the issue is resolved\015\012or post a comment for further assistance.
\015\012
\015\012Thanks

\015\012\015\012

Rylee

Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I bought a used 7 1/2 year old fisher paykel dd603 for my tenant, it worked fine the first time. second time she got F1 code on both drawers. water was in lower pan, we sopped it up and dried it out. also drawer was not seating level but was lower on left side, and insulation had fallen off left wall. all now corrected. but now the top drawer leaks onto floor on left side. it did not leak before repairman came out, we checked thoroughly. repairman says top lid not seating properly and i need ne


I have the same model F&P and just experienced similar problems. My top drawer was leaking due to that "not important" thin white tube. It really sounds like you called a general appliance guy and not a trained F&P repairman. The guy who fixe ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Top drawer leaks onto floor. bottom drawer works ok.


Looks like you were being helped by another consultant. Unfortunately I do not have access to what solutions were suggested. But reading in between the lines it appears you are checking if the lid seal is moving correctly.\015\012\015\01 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have the two drawer model dish-drawer system. In the past the top seal leaked and since has been replaced with a new seal. Worked well for several years after but then the top drawer quit running. So we started to use the bottom drawer. That was fine for awhile althought it would pump waste water into the top drawer. Now neither drawer will work. The bottom drawer starts up and shuts down. I pulled the lower drawer and it is dry.


If your model has got an LCD display are you able to record what shows up on the display when the bottom drawer shuts down. If no display then are you able to note down the LEDs which are on inside the top of the drawer lid. It is likely there is no ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have the two drawer dishwasher. It's about 10 years old. The top drawer continues to work OK but for the last three attempts when I run the bottom drawer water gets out into the drip pan below and gives the F1 signal. I can dry the drip pan out and clear the F1 signal so the top drawer works. But running the bottom drawer causes water to leak again with the resultant F1 signal. There is very little water in the bottom drawer (just a little in the filter bowl) so I think the pump is pumping


Hi,Unless you keep using the wrong detergent or keep putting dishes that \015\012are to tall in there. i would have to say your actuators ar bad and its \015\012not letting the lid go down to seal it all the time.There is no adjustment. Y ... Fisher and Paykel Dishwashers

Top drawer works but bottom drawer shows code u3 and bottom drawer started leaking water before the u3 code showed up


U3 code generally relates to drain pump blocked. This could mean the water is not able to drain out. Leaking of water is not a good sign. Shows the vacuum seal is not working.\015\012\015\012Clean the drawer door from inside and make sure ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My top dishdrawer stopped working half fill of water. I put it on rinse cycle and it drained the water. I found a bit of sand in the bottom of drawer. I wiped the sand out and then put onto a cycle. After a couple of minutes the dishwasher started flashing a tap symbol with a slash through it and stopped working. Any help please:) Jacki


... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

We have a Fisher& Paykel dishwasher with 2 drawers -- one on top of the other. Model DD603. The bottom drawer works fine. But the top drawer is not working properly -- it repeatedly stops in the middle of the cycle and there is water left in the drawer. Previously when this happened, we called a repairman; he removed the top drawer from the machine, said it was "off track", flipped some lever, and put the drawer back. He seemed a little embarrassed by having to charge for a service call for


Are you able to provide a bit more information on what you see when the dishwasher stops in the middle of the cycle -\015\0121 - is it displaying the time remaining in the cycle and is it always the same time?\015\0122- do you get any fau ... Dishwashers

How do I adjust top drawer height? The seal around top drawer appears to be leaking and there is a lot of dried residue around the top edge of the drawer. Water appears to be leaking from the top.


Not sure if adjusting top drawer height will fix the leak. The only way to fix the drawer seal leak is to take the drawer out and check what is wrong with the seal which is located around the top edge of the cabinet from inside.\015\012\0 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Water is leaking from the top of the top drawer, mainly on the right side of the top drawer. Is there an adjustment to raise the tub so that it would have an even seal to prevent the water from leaking. I noticed that the top drawer has a bigger gap on the right side or has more give-in/movemenet when the tub is lifted compare to the left side. This casue the flooding error at the end of the washing cycle.


I have had similar problems with my DD603SS. The leakage leads to the water detection in the bottom of the unit and the resulting F1 error. The movement and height of the lid is controlled by the lid actuators. There is one on each sidewall. The draw ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a F and P 603 dishwasher with a similar problem as to a recent post here. My top drawer doesn't turn on and my bottom drawer does. Well it just has after I swapped the "blue" motor inside from my top one. Now, I have tried and opened as far as the translucent "X" plastic from the bottom of my bottom drawer showing the motor and it looks fine. I have even swapped the control board from my top drawer to try and see if it works and it actually does. So, problem persists. Top drawer do


Alright, open up the outer panel of the machine. Note the positions of the wires on the switches and\015\012remove them, unclip the switch housing from the base panel. The\015\012switch housing contains one switch for each drawer. The switches are\01 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dishwasher top drawer was dead so i was told to change the heater under the drawer i did that but now i got more broblems the top drawer lights up just beeps for a second and does nothing as for the bottom which did work before now works for 1 full minute and then just flashes on and off iam confused can tou please advise me joseph.


Hi,Whenever the Drawer is Dead, there could be a couple of Reasons. First, it could be a Bad Heater Plate or Bad Control Board on the Front.You could remove the Control Board and Check.More often, you would find visually, that they are Ho ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Fisher Paykel DD603 both drawers are leaking F1 code bottom drawer is not as bad as top. Can sometimes make it through a load with no F1. There is water underneath lid seal on both at end of cycles or in the case of the top half way through. Checked hoses not leaking.


Change your detergent, high foaming detergents leak through the overflow, highly unlikely that both drawers developed a leak at the same time. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

The lid of the top drawer leaks. I've examined the seal and it appears sound. Water is on the top edge of the drawer.


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Fisher & Paykel 2 drawer dishwasher: I too cannot get power to top drawer. 4 days ago we had an F1 code. My husband pulled out drawer, wiped up water, and dried it out. Put it back in overnight, and both drawers worked fine. Now the bottom drawer is okay, but no power to top. Help!


He might have unplugged something in the proccess of drying the bottom ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi, I have a fisher and Paykel double dish drawer model DD605. A couple of days ago when we opened the top drawer all the lights flashed and beeped in sequence repeatedly and would only stop when the power was turned off or the dishdrawer closed. Today I went to turn the top dish drawer on and cannot change the cycle off rinse. I can push the eco button and the rinse cycle works no problem but I cannot change the cycle. The bottom drawer is running as I write this and appears to be fine. An


Hi\015\012\015\012\015\012Could you please let me know which all lights are blinking/lit solid in sequence from right to left. This could be an issue of drawer lock mechanism or flood switch issue. PLease post back with detai ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

The dishwasher top drawer is leaking all over the floor during the cycle. When the top drawer is running, It fills up the the bottom of bottom drawer with water also and then neither drawer drains completely. The water is a light brown color after a wash and often half the soap is left in the dispenser.


Fisher and Paykel design a air gap kit to prevent the water back flowing to the other while one is running. it really works and worth of your money.\015\012You need to change the lid seal and a pair of actuators from the top drawer. Because of the ... Fisher and Paykel DD605SS Stainless Steel Dishwasher

Hey Everyone! Ok try this one! I have been working on a KUDS25 Kitchenaid Dishwasher. It was leaking like a siv from the bottom. I replaced both top and bottom plastic bearings and also tightend all the screws at the bottom. Leak Gone, I thought. It now has small leaks down both sides. I have since been told by the owner that he took the door apart himself. I pulled out the dishwasher from the cabinet and ran it. I could see the leaks at the top on both sides of the door latch. I cou


Hello davidgalb. You can install a new gasket to seal the door again. That old seal is not flexible any more. That said, for my time and money I recommend a replacement dishwasher, this one has definitely seen better days. Joe ... Dishwashers

The top drawer is leaking apparently from calcium and/or lime deposits on both the top of the drawer and the rubber gasket on the lid. I need to get the drawer out but can't see where to disconnect the hoses to allow for drawer removal.


There are small tabs at the front of the drawer.. one on each side, down at the bottom of the drawer... push in on those tabs. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

We have a Fisher & Paykel two drawer dishwasher, model DD603. The top drawer doesn't work - when you push the Start button, there is a series of 4 quick beeps, and there is some symbol of a dish with 3 drops of water, but it doesn't do a wash. The bottom drawer works fine. Though the unit is level, the drawers do not appear to be well aligned. Any ideas?


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Dishdrawer The top drawer of our dishwasher has stopped working. It has been working fine for about 18 months but now it seems to have no power coming through to it. The bottom drawer is still working fine. There have been no electrical surges that we are aware of.


Hi there,\015\012\015\012If you have no power to the top drawer and it is difficult to open it may be that your heater plate has blown and requires replacing. If it has no power and opens easily you may have the child lock on and need to hold the loc ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Greetings. I have a Fisher & Paykel dishdrawer - the top drawer appears to have lost power mid cycle and the lid has not retracted - no led display - no response from the buttons. The bottom drawer functions ok. I have tried turning the power off at the wall for 30 seconds and on again. I have tried swapping the top and bottom controllers and the bottom still works but the top does not, so the controllers must be ok Not sure where to find the model number sorry. Any suggestions?


Describethe inside of unit,any wear on it anywhere, the rack the dishes go on is it plastic coated? is it wore with rust comeing though on tips here and there? ... Fisher and Paykel DishDrawer DS605FDSM Stainless Steel 23 in Builtin Dishwasher

I have a mdd8000aws dishwasher. After a power outage (2 days) the power came back on, and the bottom drawer no longer works. It still make the chiming noise when the drawer is opened, but the control panel is not fully lit up and the washer will not start in any mode. The lights seem to flicker for a short moment and then they all stay very lightly lit up. Is this just a bad control panel or is there some other circuit that needs replaced? BTW, the top drawer works perfectly.


... Maytag MDD8000AWS Builtin Dishwasher

Kitchenaid kudh03dtss cancel, power, rinse aid and clean lights are all lit and no other buttons work on the bottom drawer. top drawer works fine. how can i reset the bottom panel?


... Dishwashers

Fisher Paykel bottom drawer not working just hear a thump thump thump noise and doesn't start. Top drawer works fine.


Try putting water manually on bottom drawer, do this only with the unit unplug, not connected to power be careful .then turn it on, watch, and hear what will happen, hope this help ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Hi, I have a Fisher and Paykel DD603 dishwasher. The bottom drawer works fine but the top drawer doesnt work at all. It appears normal until the start button is pushed and then I get 3 very quick beeps followed but a 4th slightly longer beep. Then nothing happens, any ideas or help would be much appreciated. Thanks Neville.


... Fisher and Paykel 24 in. DD603MFC Built-In Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0777 seconds