Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

STOP WORKING SHOWING F2 CODE

\015 STOP WORKING \015\012SHOWING F2 CODE\015

Answers :

F2 error are related to motor problems. The most common is a grime going in from the drain filter and getting stuck around the motor rotor cavity.
\015\012
\015\012Just follow the instructions in your user guide to clean the filter plate. At this point you can take the rotor out and clean the cavity. The rotor can be pulled out carefully without pressing too hard on the impellers.
\015\012
\015\012If this does not help then try to clean the connecting link between the drain filter and the motor cavity. You will need a thin stiff wire for this.
\015\012
\015\012If all of these doesn't work, the rotor might be broken and needs replacement.
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have an Asco type DW 95.5 built-in, model 1885. During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric still runs. When I pop the circuit breaker, all is stopped. However, when power is restored, the lights and code flash as above, and, again, something electric runs. My email: [email protected] Thanks for any help...


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your description " During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric s ... Asko Dishwashers

My dishwasher stops during the wash cycle with a "uo" error code. I can not restart the load until it cools down and then sometimes it stops again during the cycle with the same error code.


... Frigidaire PLD4555RFC Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

I have an IAG dishwasher that keeps stopping on cycles before the dishes are dry and coming up with error code E7 which asks me to rerun cycle and if code appears again contact maintenance. Any suggestions on what code E7 means


... Dishwashers

Code 0E The code 0E shows up about 15 minutes after we start the dishwasher. The washer completely stops when this happens


Hi,The OE code on an LG washer is a long drain code. It is saying that it has not drained within ten minutes.You will need to check the door on the lower left hand side and clean out the filter. If the filter has nothing in it ... LG LDF6810ST Stainless Steel Built-in Dishwasher

My dishwasher stops and displays a pf code when there is 38 mins left in the cycle. After it displays the pf code it restarts itself. So my dishes never get to go through a full cycle. What do I do?


Sounds like you need a new timer/control. They are preprogrammed to control the functions. Any change cannot be corrected. To replace try this link http:/ ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

The dishwasher keeps stopping mid cycle and displays either E3 or E4 error codes, we haven't got the manual so would appreciate if you can advise what those codes refer to please


... Hoover 24 in. HD97E Free-standing Dishwasher

Caple DI604 dishwasher stops almost immediately after starting. Error code is that the 3 left lights are on when I open the door. Does anyone know what the error code means?


... Dishwashers

Coleman mobile home furnace...Model number DGAA077BDTB...The furnace about a month ago started going out ( flash code- Combustion Air switch stuck closed)We replaced the thermostat on the wall and it stopped doing it and ran fine then last night it stopped again ( Combustion air switch failed to close) and when i got up the furnace was working and now for the past few hours it refuses to do anything...I am on a very very tight budget...and need some idea of what is wrong and do i need a professi


I had the same errror code on my coleman furnace (3 flashes combustion air switch failed to close) but at first didnt realize there was even a light that gave codes..Anyways long story short, after searching many forums one guy mentioned about the fu ... Dishwashers

LG 5811 dishwasher stopped, OE code came on, water will not drain & cycle stopped


Drain hose error. make sure the hose is not kinked ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on


I just spoke with the Customer Service rep from Danby... She said tht an E2 error has to do with the hoses. Usually it means that the hose is too high to drain properly, there is a kink in the hose or the pump is faulty. Hope this helps! ... Dishwashers

Dishwasher will start, but after a few minutes a noise starts. It will start and stop a few times and then it stop. The code LE appears.


It is time to remove the filter down in the sump area, underneath the bottom spray arm. The spray arm comes off simply by pulling straight up. Also, the upper basket can come out by pressing on the gray clips, which will come off in your hands and ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

E4 code, Can't stop the machine trying to empty. There is no water in it, have even tried fooling it by putting water in. Error code shown is E4, which indicates overfill, but that is not the case. Help :)


... Baumatic 23 in. BDW9 Built-in Dishwasher

I have a NVDE12W NOUVEAU dishwasher only a year old and it stops working midcycle with a error code E3. However I don't have a manual to know what this means? Its happened a few times and now I think it maybe stuffed? Can anyone tell me what this error code means?


Hi\015\012\015\012Thanks for using FixYa. E3 error means that the water heater element does\015\012not work properly or the filter mesh is blocked. You'll need to clean the\015\012filter mesh; if still the issue is not resolved t ... Dishwashers

A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a


As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers

Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on I bought mine new off the internet and it's been running great for about 2 months. Now I can't get it to drain and E2 shows, I can't get my money back because I've had it more than 30 days, if the solution is a pump, I'm tossing it and getting a good one from


E2 is a hose issue. There is either a kink in the hose, the hose is too high to drain or the pump is faulty.1-800-26 DANBY ... Danby DDW497W 22 in. Countertop Dishwasher

E4 error code in powerpoint IDW8. Water inside base. When moped up m/c operates for a short time and then stops , repeating the E4 error code.


... Dishwashers

I have a Kenmore ultra wash quiet guard 3 dishwasher with a Hi Temp Wash that won't stop flashing. I've tried shutting off the circuit breaker and every code button sequence I can find including pressing Hi temp wash, heated dry, hi temp wash, heated dry...but it won't stop blinking..always blinking...Anyone have any other suggestions to reset this?


... Kenmore 24 in. 17019 Built-in Dishwasher

E3 code I have a Danby countertop dishwasher. It will come on and start the cycle but then it flashes the E3 code and stops. I just got it a week ago, what could it be?


Received from Danby customer support:\015\012"The error code of E3 tells us that the unit is not getting the proper water temperature to continue thru the entire cycle. Before starting the dishwasher and attaching the quick connect assembly to ... Danby DDW496W Free-Standing Dishwasher

Dishwasher keeps stopping and beeping continuously until I press the start button again and shows the F8 Code. When I press the start button it continues for about 5 minutes and then stops properly but there is lots of foam still in the bottom of the dishwasher.


Sir i think the problem would be in any of the three areas. any prob in these areas would lead to the problem u specified\015\012\015\012Test the timer motor.\015\012 ... Dishwashers

Fisher & Paykel DD603 model Upper Dishdrawer has F3 fault code. cycke starts, then stops within minutes. Water in tub after stopping is not hot. Temp sensor bad? Could you please send pdf of servie manula for dd603 please? Thanks [email protected]


F3 means your dishwasher water is too hot. Go to the link below and it will show you how to determine what is causing the error. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Im receiving an OE error code on my LG Dishwasher Model LDF7811st. The machine runs for a little bit and then it dings a few times with the "OE" code and stops running. HELP please


The LG error code OE simply means "the pump is blocked". Presumably the water isn't being emptied properly. As with all error codes it is possible that there is a cause other than the exact description in the error code explanation but basically this ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

I have a whirlpool dishwasher model number gu2400xtpq7. It stopped working. A fladhing light statred to blink. Light is "call for service" . Light blinks in series, 7 blinks and then stops. What does this code mean?


... Whirlpool GU2400XTPS Built-in Dishwasher

My Electrolux 66010 dishwasher stops mid cycle with fault code 60. What does this mean? This code is not listed in the manual. Thanks.


... Electrolux Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0801 seconds