Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

Hi. I had f1 appear on my Gisher and Paykel dishwasher. Unplugged from wall. Few days later dried using a hairdryer. Took cover off pcb board and dried in there as well. There was water on bottom of cabinet so understand the F1. Problem is now, I put cover back on pcb board and tried to power up but it is dead? Any sensor.microswitch on PCB cover, or anything i may have missed? No power at all to unit? Any assistance greatly appreciated. PS - Wall socket finer as powers other appliances.


Answers :

Wait..................
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi. I had f1 appear on my Gisher and Paykel dishwasher. Unplugged from wall. Few days later dried using a hairdryer. Took cover off pcb board and dried in there as well. There was water on bottom of cabinet so understand the F1. Problem is now, I put cover back on pcb board and tried to power up but it is dead? Any sensor.microswitch on PCB cover, or anything i may have missed? No power at all to unit? Any assistance greatly appreciated. PS - Wall socket finer as powers other appliances.


Wait.................. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

LG - LDF7811ST Dishwasher will not turn on at all. I have replaced the main PCB board and checked all wires for shorts. The PCB board does have 120Vac to the board. I have also checked the latch and it does close the switch when the dishwasher is closed. I think it may be the main switch/power button board but can't seem to find the part number or alternate part numbers that can be used.


Hi. The likely culprit will be the power switch. The part number for this switch is 5020ED3011A.NOTE_ Make sure there's power getting to the dishwasher. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for po ... Dishwashers

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch Comments: Aug 22, 2009 - I tested the door swich and I have power on both poles when it is closed. there is 2 switches on the latch but the one with power to it powers up the circ


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

Dishwasher would not work and clean light would blink seven times. Asked an expert and they said to hit saniwash and heated dry two times. This work for a couple of times but now the dishwasher acts like there is no electrical power goimg to it. I tested the power with a voltmeter and there is power going to the circuit board.


Normally this happens when the dishwasher electronic control does not detect a water temperature increase during the main wash cycle. The issue could be in the heater element, the thermostat or the wiring that is connected to those or on the electro ... Dishwashers

I've got a GE model GLD4408R00WW front load dishwasher, which was not filling, even though you could hear the motor running. Tried resetting it by turning off the power at the wall switch, and then from the breaker itself, but now, see the "Normal" wash cycle and Heated dry lights blinking when power is returned...


Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher Tr ... GE Dishwashers

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

Gibson Furnace Hi and thanks for reading my question. I have a Gibson furnace with electronic ignition. When I turn on the power to the furnace it starts running with the batteries removed from the thermostat. It blows but does not produce cool or or stop running. The circuit board has a small red light that is flashing but does not seem to have a pattern. I would appreciate any input that you may have. Also are the relays located ont he circuit board itself?


... Dishwashers

I have fitted a new pcb in my dishwasher de6855 the power button is working but i can not get a prog is there something stoping the power geting to the board


You could have a bad power supply aka high-voltage transformer. Have you tested the power from it to the board? Have you checked any fuses or relays? I would start there ... Zanussi Dishwashers

I have an Indesit IDL500 dishwasher. It had stopped heating the water up, it looked as if it had short circuited and so i replaced it, i have power going to the element. A couple of forums state that it may be the pcb behind the timer/selector switch. Does this pcb control the program selection and heating of the element? or is there a thermostat that controls the stop and start of the heating element? Any help would be greatly appreciated


Hi\015\012\015\012The unit\015\012has two thermostats and you can test both of them for continuity before\015\012replacing, no continuity replace the thermostat. Hope\015\012this helps...please post back fo ... Indesit 24 in. IDL500 Built-In Dishwasher

Something was stuck in the latch, which made the machine not start. I removed item, however, the lights come on, the heat comes on, bot no water or the rest of the cycle begins...help.. I have held down start/cancel and the heat dry buttons. I have unplugged the power for three minutes... I have taken the front covers off, looked through the latch mechanism but found no other issues. There is a little water left in the basin, so I checked to see if there was a clog, by blowing air into th


Hi,Sorry for the delayed response. Your problem dated 30th Sep 2009 was reposted today on FixYa. I am sure by now some other expert must have responded to your question and solved your problem.If this is not the ca ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Arthur martin asf2656a. The dishwasher was on a 50- deg eco setting and got stuck at 30 mins and will not stop or go further. If I turn off the power it remains stuck. There may be a blockage. How do I get into it? there is a large plastic cover on the base apparently with componenets attached. O see no fixing screws


... Dishwashers

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

I have the GE Quiet Power 3 Model gld4400n10bb. When I start a wash I can hear it fill with water (to about 1/2 inch below the heating element). It then waits for about 5-7 minutes and pumps the water out. It fills again several times and pumps out. It doesn't sound like it is washing though. The whole interior of the dishwasher is covered with dried soap. I can also tell that water is not spraying around the whole interior. Any ideas?


... GE GLD4400NWW / GLD4400NBB / GLD4400NCC Dishwasher

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch


Possible switch panel. When you press it does it feel like a click as the the other buttons? If so you probably have a bad circuit on the inside, if it doesn't click the heated button switch is more then likely the cause. ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

The key lock light stays on. I held the heated dry button for 4 seconds and the light still stays on. I think it may be the control board, but I am not sure. Can anyone help me please?


If the light is blinking, it is definately a stuck button and the console will need to be replaced. If it is on steady, it could be a console or control board problem. There are no troubleshooting tips to figure out which one is faulty, the manual sa ... Whirlpool GU2400XTP Built-in Dishwasher

I have a JDB1090AWS about 3 years old. We noticed a smell and found cutting boards and plastic cups melted. Machine was off. Had to turn off the breaker. Checked both leads to element & have power even with machine off. Not sure if it could be the limiting thermostat; I assume that is to shut the heat down when it gets too hot. Element is on though when it shouldn't be to begin with. I did have to tighten the water supply. Had some water underneath, but all wires seemed dry. Any tests I should t


The heat element can only get so hot.It's timed so it doesn't exceed a period of on, exposing dishwasher contents to continuous high temps.Watch the timer and take note how long it broils your cookware.Good luck. ... Dishwashers

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

We have a n eight year old fully integrated asko dishwasher. Only the rinse cycle works, so I rinse many times - last rinse with detergent and then run the short program which does not wash, but will dry the dishes. The circuit board was replaced once before under warranty($500.00 labour) and I suspect that we may have to do the same again. Can we find this on the internet and do it ourselves; we have good electrical knowledge. Thank you in advance.


This is most likely an issue with the timer. Timers\015\012don't often fail. But if every other part of the dishwasher seems to be\015\012working properly and the timer knob seems to be stuck in one\015\012place--doing one function continuously--the ... Asko Dishwashers

Bosch SHU4302 WITH REPAIRED PC BOARD has been working fine for several years now seems stuck in rinse/drain mode and is not quite pumping cabinet dry. I have removed the screens and located the small impeller at bottom below cover. The impeller rotates as though it has multiple spring loaded stop positions. When I turn on the unit and open the door water is trickling from the sprayer arms at low pressure. It seems stuck in rinse mode and will not advance cycles or reset when shut off.


... Bosch Dishwashers

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

Kitchenaid kuddo1dppa I own a KitchenAid KUDD01DPPA, 2 drawer dishwasher. I am not a technician, however I have had a lot of experience in repairing various appliances and am savvy with electronics and mechanical technical issues. Here's the problem: I was getting rinse error codes in both drawers, pulled the bottom drawer out, removed the cover to the circuit board and used a dryer to dry up the moisture on the flood switch. Now I am getting Fill Failure error code on both drawers. I have g


Test this steps and fix it. God bless you\012 \012 Water Inlet Valve\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

SHU 5316 UC dishwasher by bosch. I think it is from about 1998 or 99. It blew a circuit breaker yesterday. I reset the circuit braker, but it won't even power on. It may have burned something out. We replaced the control board 2 years ago. Please tell us: 1. Is it worth fixing again, or just replace? 2. Any suggestios? Maybe the pump has shorted? THANKS SO MUCH!! Mark


Hi Mark -There's no internal fuse in this dishwasher, so if there's no power you may well be looking at a new control unit and probably another major component as well, depending on what caused the overload or short. The most likely ... Bosch SHU5316UC Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1109 seconds