Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

F1 code I have cleared all water out. still have f1 code now what?


Answers :

You need to reomve the drawer and look in the back there is a board there that needs to be dry before it will reset unplug the unt or turn off at breaker and dry board off it has a water sensor built in also you most likely have to replace the actuator motors on the lid they are not keepimg it tight
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On my bosch shu66 diswasher the error code indicates a number 1, aqua sensor I think. There is a screw missing in the soap dispensor and it's been letting water into the door interior. could this be repaired by replacement of the screw and drying out the interior insulation and wiring The solution I tried didn't clear the error code on the panel. Is there a reset or do I need to replace the aqua sensor or ? The machine still won't start and displays a #1 on display. There is no water in the whi


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

F1 code I have cleared all water out. still have f1 code now what?


You need to reomve the drawer and look in the back there is a board there that needs to be dry before it will reset unplug the unt or turn off at breaker and dry board off it has a water sensor built in also you most likely have to replace the actuat ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Dishlex Global 500 dishwasher (DX500lWW*b). Woke up the other night to find water all over my kitchen floor. The hot water hose connector to the hot water tap split (bursted). The dishwater was not in operation at the time but I can only assume when the hose bursted the dishwater came on to alert me? the code on the dishwater is displaying ''oF'' - which means Incorrect fill level of fill time. I have consequently had the hose connector repaired but the display still has the code ''oF''


I found this\015\012\015\012"Hi - answer I was given by Electrolux Help was: pull machine out from under bench onto old towel, tip GENTLY onto left hand side (your left as you face the front of the machine) after it has drained, stand up ... Dishwashers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

I have a candy trio 501 dishwasher with intergrated oven. When I put a cycle on it starts its first rinse then after 5/10 mins stops and beeps constantly. It's still full of water too. When I put it on rinse cycle it compleates the cycle so inlet and drainage should be ok. Ive removed drain pipe and made sure its not kinked and also clear. I've removed and drained the compartments that had water in and also blew down the pips to see if clear all ok. I've checked the heater element with meter and


... Dishwashers

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

G7856 showing Fault Code F26. Have cleared filters of all debris, including drain impellar (sp?) cover. Code still not clearing. What do I do next?


Hello there again I dont know if you got disconnected or just left the chat room but please try this take out the bottom white basket so you can see the\015\012bottom inner of the dishwasher, then take out the centre filter and\0 ... Miele 24 in. G638 Plus Free-standing Dishwasher

I have dishwasher (Electrolux) model ewdw6505gs. How do i clear a code of 01? I fixed the disposal clog and the dishwasher automatically drained the water in the bottom. I just can figure out how to clear the error code.


I should inform you that that is a "leak detection error".\015\012You should check some of those hose clamps, they may not be tightened properly.\015\012\015\012Regards ... Electrolux Dishwashers

My Kenmore 15705 dishwasher runs fine through the cycle but still has water in the bottom after it is done. It cleans fine, is clear of food particles, and drains fine during the wash cycle. Why is there still water in the bottom?


... Kenmore Dishwashers

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

I have a Bosch Dishwasher Model # SHU43C that is not washing properly. Some dishes are not being cleaned if we don't pre-scrub or rinse. There are no error codes on the panel. During the cycle I hear the pump motor starting and stopping repeatedly on about 1 second intervals. I suspect it may be starved for inlet water. I checked the inlet water line and it is clear. We use well water that occassionally has some iron sediment in it and it plugged the inlet water screen for our washing mach


Hi,\015\012It is very possible that the screen is plugged...most inlet valves have a screen just like your washer does. I would at least remove the hose/pipe and check the flow...and check for a screen. \015\012Also the solenoid can get j ... Bosch 24 in. SHU43 Built-in Dishwasher

Error Code E1 means longer inlet time. possible causes faucet is not opened, or water intake is restricted, or water pressure is too low, according to the BRADA portable dishwasher model EP9242AWW What does that mean and how do I fix it? I have shut the water faucet off and the error message still shows.


... Dishwashers

I have a problem with a bosch dishwasher i put in a kitchen 10 years ago. knob on left side buttons on right , stainless steel interior. i dont think client has ever used it. he must have put in new disposal but did not clear knock out. he went to use it with regular dish liquid.it started to leak and foam. he left me a note to look at it. 10 hrs later its still running and water is everywhere. i disconect from disposal and pump water into bucket but now can not get water to go in to it. tried b


First check that the valve under the sink is turned on sorry have to put this part in next thing to check would be the inlet water valve and assure that you do have power going to the valve if you dont then you would look at the float switch as the p ... Bosch Dishwashers

I have an ADP6000IX Whirlpool dishwasher which is comming up with a Fault code Err4. The manual indicates overfilled and possible cause "too much inlet water", however there is no water sitting in base of machine, and have unloaded all dishes and Err4 still comes up. I have switched unit on and off at wall but has not re-set. I have disconnected water pipe from tap and reconnected.Is there anything further I can do?


Hi, \015\012\015\012You can solve this by cleaning and de-greasing the filter frame, basket and sensor Also there might be a low threshold for oils/greases/debris of any kind, so you have to rinse and load. By removing outflow tube ... Whirlpool Dishwashers

My dishwasher won't drain. It starts a cycle but doesn't finish draining the water. I checked the outlet hose and it's clear. I was able to siphon off the water and start a new cycle but the water still won't drain. Time to replace the pump?


Hi,\015\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Water will not drain ... Kenmore 15879 Built-in Dishwasher

Hotpoint fdw70 error code A10 have replaced the inlet water valve but still have an error code flashing A10 hoped to find a reset button but cant find it anywhere can u possibl advise.


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Foggy stains I have tried every solution to wash my dishes and clearing agents. But I still have a lot of water fog stains. I am not sure if it is the water or the dishwasher! Help


It is/was the detergent that was used to wash the dishes with. ... Kenmore 16919 Built-in Dishwasher

Bosch Dishwasher SGS45E02GB/45 partially fills then empties repeatedly. Have replaced flow rate meter; still the same. Water matrix; pressure chamber and hoses clear, not blocked; float valves operating. Control module has no sign of burnt joints. LED does not countdown; water level inside machine does not reach correct level. Any suggestions?


... Bosch Dishwashers

Miele dishwaher won't drain, water in the bottom of filter. I have cleaned filter, water still won't clear.


Hi,most common faults with dishwashers is a drain fault. Check for any kinked hoses and check the drain spigot under the sink where the drain hose connects into the u bend. Usually this is where food gets trapped due to ... Dishwashers

Husky HU80722 model Water flows thru the washer. Have disconnected all hoses, checked filter screen it is clear. Reconnected hoses, Engine runs fine home water pressure fows through washer. Still not producing any pressure.


... Northstar Pressure Washer 3000 PSI

I have a GE Potscrubber 720 and there is water in the bottom of the dishwasher and I tried to clear it by starting a cycle and it still keeps water in the bottom of the washer. When I run a cycle there is caked on soap on the inside door and dishes and the dishes are filthy. I found a long thin piece of metal by the drain it is long and straight and a break on one end and an "L" shaped bend on the other.. Any ideas where to start looking for problems? As I have no experience in repairing dishwas


... GE 24 in. GSD2600GBB Built-in Dishwasher

Our whirlpool estate diswasher will not drain the water after a wash cycle. I have removed internal parts down to the drain and cleared the path. Moreover, I have removed the drain tube and clean it. Still water will not drain. I assume it is the pump. Can the pump motor be easily replaced? Thank you, Jim


You hve to find the right pump first ... Whirlpool Dishwashers

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

We used our LG diswasher to clean our grill grates, which was a bad idea, because now the unit will not clean the dishes. We cleared the washer arms of debris, but the unit still is leaving the dishes on both racks dirty and is leaving the liquid soap dispensed into the unit undissolved on the door of the unit. There are no kinks in the water inlet, and water is getting into the unit, but the dishes are not getting cleaned.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please make sure the dishes are loaded properly or\015\012dishwasher is not overloaded. Also check that the dishwasher is filling\015\012properly. It will fill with water up to ... LG LDF6810ST Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1325 seconds