Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

F1 Code for both Drawers

\015 What is the F1 Code\015

Answers :

F1 could mean several problems. However when it occurs on both drawers it means the flood switch at base of dishwasher under the bottom drawer has triggered. This is caused by water leakage. Make sure the dishwasher mains power is turned off to avoid damage to dishwasher. You can attempt to dry the water and find the cause of the leak. Usually foaming due to incorrect or too much detergent, leaky lid seal or hoses broken.
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kitchenaid kuddo1dppa I own a KitchenAid KUDD01DPPA, 2 drawer dishwasher. I am not a technician, however I have had a lot of experience in repairing various appliances and am savvy with electronics and mechanical technical issues. Here's the problem: I was getting rinse error codes in both drawers, pulled the bottom drawer out, removed the cover to the circuit board and used a dryer to dry up the moisture on the flood switch. Now I am getting Fill Failure error code on both drawers. I have g


Test this steps and fix it. God bless you\012 \012 Water Inlet Valve\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

I have the "rinse" error code on my kitchenaid double drawer dishwasher kudd01dppa1. I've turned off the power, then it worked for one load and the code reappeared on both drawers again. What should be a next step? it says in the manual that the "rinse" error code means that something happened to the flood switch...? Can this be fixed without calling out the kitchenaid technicians? thanks


... KitchenAid 23 in. KUDD01DPPA Stainless Steel Dishwasher

Top drawer works but bottom drawer shows code u3 and bottom drawer started leaking water before the u3 code showed up


U3 code generally relates to drain pump blocked. This could mean the water is not able to drain out. Leaking of water is not a good sign. Shows the vacuum seal is not working.\015\012\015\012Clean the drawer door from inside and make sure ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

F1 error code due to water coming over the top of the top drawer at beginning of cycle. Previously, I had this code and followed the instructions found here and resolved the problem (a foreign object had blocked the drain). This is different and I need to find out WHY the water is flowing over the top. Could the top drawer just not be sealing properly when closed?


Hello,\015\012\015\012Here a link to a F&P repair video.\015\012\015\012Dish Drawer Repair Video\015\012\015\012http://www.appliancerepairlesson.com/shop/dishwasher-videos/fisher-paykel-dishwasher-repair/ ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Fisher and Paykel DD605i dish drawer. We have a U1 error code on the top drawer and had this same problem just over a year ago. A repair person replaced the inlet valve I believe. I am wondering if there are any tests I can put the machine through or if this is something I can fix myself to see what is causing this code.


... Fisher and Paykel DD605I Dishwasher

Fisher & Paykel 2 drawer dishwasher: I too cannot get power to top drawer. 4 days ago we had an F1 code. My husband pulled out drawer, wiped up water, and dried it out. Put it back in overnight, and both drawers worked fine. Now the bottom drawer is okay, but no power to top. Help!


He might have unplugged something in the proccess of drying the bottom ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

We just purchased a used Fisher and Paykel DS 603-i. After installing and running the normal cycle there was a lot of water left on the bottom of each drawer. We ran the bottom drawer (water stil siiting on the bottom of the top drawer) and part way through the main wash cycle we got what I think was a F1 error code (we do not have the LCD version but the Rinse light was activated). I took out the bottom drawer, dried out the basin and then took out the washer and reattached the drainage pipes t


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You’ll need to reset it by poweri ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

I have a dishdrawer (2) and following the use of a dishwasher cleaner, the bottom drawer appears to have developed a blockage. It will not empty, gets to the pump out part of the cycle and shows the red error code F3, to which there is no reference in the trouble shooting guide. The top drawer has also developed minute leak, sufficient enough to leave dribble marks on the lower drawer and over time, a white deposit on the floor. Is there anything we can do for the blockage problem before reso


Remove the small basket from each drawer and lift up the removable plastic cover and take the drain filters out , empty them of food by products and try it again.. If you've never cleaned them then that's your problem with the drain process.. Hope th ... Fisher and Paykel Dishwashers

I bought a used 7 1/2 year old fisher paykel dd603 for my tenant, it worked fine the first time. second time she got F1 code on both drawers. water was in lower pan, we sopped it up and dried it out. also drawer was not seating level but was lower on left side, and insulation had fallen off left wall. all now corrected. but now the top drawer leaks onto floor on left side. it did not leak before repairman came out, we checked thoroughly. repairman says top lid not seating properly and i need ne


I have the same model F&P and just experienced similar problems. My top drawer was leaking due to that "not important" thin white tube. It really sounds like you called a general appliance guy and not a trained F&P repairman. The guy who fixe ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Hi My F&P dishdrawer flooded. Dried it all out etc, the top drawer doesn't complete the cycle and it beeps continually even when it's not running. I am wondering if I can reset the drawer using the front buttons to get it back to factory default. Bottom drawer works fine. There is no error code on the screen only the lock icon which won't go away. Any ideas?


Not sure if you tried turning the power off at the main switch. Lock icon can gone away if you press the necessary keys as shown in the user guide. Also the sequence of keys to press for getting factory defaults of different options is also in the us ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

3 problems: 1. lower drawer is hard to close; seems to be sticking on something. 2. lower drawer retains water (2 inches) after completing a cycle. 3. F1 fault code on both drawers with alert occurred when washers were not in use. I had to turn off the electric circuit breaker to make it stop.


Ok where to start, first thing the bottom draw is hard to close because they use 2 little motors on either side to pull a lid with a seal on it down on top of each draw when u start it to keep the water in, if its hard to close the motors are damaged ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

On our double drawer dishwasher, we are getting a code--which illustrates no water--this is for the top drawer, the bottom drawer, works fine--and the water supply is on--please help.


Sorry to read about your problem, I hope this helps you out.you must have a defective water inlet valve, for the 2nd drawer. or a bad control relay for the valve.I tried to help you. Please help me and Rate/Vote on my response ... Fisher Dishwashers

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Thanks so far! However, with the bottom drawer out and the top drawer open...I enter the diagnostic mode. I can scroll through the hardware output test mode. All the led codes appear correctly. However, none of the actual hardware responses occur....the water does not fill, lid does not move.....etc. What am I doing wrong??


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bottom drawer shows code F2 and has a low beeping, top drawer works fine.


The motor rotor is faulty or something is stuck in the rotor cavity.\015\012\015\012Remove the filter plate and twist the rotor out to check. If it needs replacement you can get it from ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

F2 code. Followed listed guidance of removing assmebly and checking...unfortunately, however, my impellar has separated from the rotor assembly and the rotor assembly is stuck in the drawer. I tried to pull up on the shaft with some pliers, but that didn't work and I didn't want to pull too hard and cause damage. Please advise as to how to remove the broken rotor assembly from the drawer. Thanks


There are no wires underneath the rotor - it is just suspended in the cavity. So you cannot do any damage except make scratches around that area. Maybe take a straightened wire coat hanger and insert from the side hole in the filter sump area. You mi ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

My Fisher Paykel dishwasher is model #DD6051. After about 1 1/2 years, the top drawer is not filling with water. The fault code looks to be U1. The bottom drawer fills and runs fine. Would you have any idea what the issue might be? Thank you very much.


Hi,Unplug the Washer for Few Minutes, say 30 minutes and then Turn it ON. If the problem Persists, then read :-U1 Heavy and Rinse LEDMachine has failed to prime with water within approx. 3 minutesReason ... Fisher and Paykel Dishwashers

Fisher & paykel dishdrawer ds605 f7 fault code. Lid failure. This is the second code (after F9- power controller fault).The lid of the dishdrawer will not raise and release the drawer. The lid is stuck in the down position. Assuming this is a power/electronic controller fault. Part numbers would be good.


You can force open the drawer without causing any damage. The actuators on each side will let you do that. But you push it back in unless you manually move the actuators for which you will have to take the drawer out of its housing.\015\012 ... Fisher and Paykel DS605ZW Dishwasher

One of the lid actuator motors died on my F&P DD603 dishwasher and was replaced by the serviceman. He put the machine in a test mode and pressed a code to try the operation while the drawer was open. I witnessed the lid closing properly. Now it appears that the other actuator is faulty. To save an extremely expensive service call, how can I put the machine in test mode and verify the actuator operation with the drawer open?


To test the lid operation first pull the drawer forward of the cabinet\015\012by depressing the lugs on each side rail and pulling the drawer\015\012forward. Then go into diagnostic mode. Once there press power once and\015\012the lcd will display "H ... Dishwashers

F1 fault code both drawers flashing and will not shut off. top drawer would not open


F1 means that u have a leak on machine and the water is activating the water detection device which is on the lid activater board located under bottom drawer.the hard thing about this problem is that to repair fault, u have to find leak which could b ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

We were hit by lighting and now my dishwasher top blinks from the minutes to an error code that look like a 118 but i don't see an error code in the book for that. It is a two drawer model


When lightning hits an appliance it hits toward least resistance, you need to replace the board in your dishwasher. ... Dishwashers

F2 Code Hey, I have a single drawer built in Fisher & Paykel dish drawer and today I pulled the spray arm, filter and large metal screen out to clean them as we have been starting to get a bit of stuff left behind after washing lately. That was all good After putting it all back in though I went to use the dishwasher and it stopped and came up with an F2 fault, I thought I may not have put the bits back in properly so pulled them out again and noticed that on the rotor that connects the motor to


Fault F2 means the rotor is not rotating. If you say some of the vanes have broken off, they could have been jamming it. This should spin freely with minimal force when installed correctly. If you removed the rotor itself, you do ned to take care whe ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Top drawer runs for a while, the timer stops after two minutes and then I get a U2 code. Bottom drawer working fine.


Hi there,Usually a U2 code means there is a problem with closing the draw fully, and hence the dishwasher thinks the door isnt closed and will not start up. This could be because A) there is something impeding the draw from closing (check ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0480 seconds