Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

F2 Code Hey, I have a single drawer built in Fisher & Paykel dish drawer and today I pulled the spray arm, filter and large metal screen out to clean them as we have been starting to get a bit of stuff left behind after washing lately. That was all good After putting it all back in though I went to use the dishwasher and it stopped and came up with an F2 fault, I thought I may not have put the bits back in properly so pulled them out again and noticed that on the rotor that connects the motor to


Answers :

Fault F2 means the rotor is not rotating. If you say some of the vanes have broken off, they could have been jamming it. This should spin freely with minimal force when installed correctly. If you removed the rotor itself, you do ned to take care when installing it - there are 3 thin plastic legs around the magnet (the blue bit) these fit into 3 slots and you need to line them up very carefully. Once you have it right, it will just drop in. The rotor asembly as a whole is secured by turning the outside clockwise until the 3 points line up with the arrows.
\015\012
\015\012Check the rotor is spinning freely, if not, remove it and check there is nothing lodged undrneath it of that it has been fitted incorrectly.
\015\012
\015\012Re the broken vanes - you could try gluing them but I think it will break. The pump spins at 4200 RPM! You may need to but a new rotor.
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

F2 Code Hey, I have a single drawer built in Fisher & Paykel dish drawer and today I pulled the spray arm, filter and large metal screen out to clean them as we have been starting to get a bit of stuff left behind after washing lately. That was all good After putting it all back in though I went to use the dishwasher and it stopped and came up with an F2 fault, I thought I may not have put the bits back in properly so pulled them out again and noticed that on the rotor that connects the motor to


Fault F2 means the rotor is not rotating. If you say some of the vanes have broken off, they could have been jamming it. This should spin freely with minimal force when installed correctly. If you removed the rotor itself, you do ned to take care whe ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

DS603 Fisher & Paykel U1 error code ..(see our previous errors we've listed) we have now pulled out the yellow water valve that goes up behind the front panel and at the other end by removing the drawer and plastic protector thingy - we checked that there were no bedris or calcium buildup in the valves ends and filters and replaced it all. So we put it all back to gether as we could not see what would cause this error, only to find that it worked - water came into the machine but about 4 mins in


This product is total ****.\015\012Pull it out, call whoever sold the **** to you\015\012and tell the to come get it and shove it up their ***.\015\012Then buy a Bosch and live a happy life.\015\012The design is moronic. The machine is like the old\ ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

The maytag dishwasher model mdb7130AWB stoped cleaning correctly so we went from the arm assembly in bottom of dishwasher down to the cutter disc and we found a crack in the housing so i ordered that piece. the new part was designed a little different but we put it all back together the way it came off. but it started and ran maybe 1 minute and stopped. so i have pulled up the diagram and see some problems. in the current diagram. original there was no part 37, 17 19 and 3, alos the crew d


... Maytag MDB7130 Dishwasher

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

We have a Fisher& Paykel dishwasher with 2 drawers -- one on top of the other. Model DD603. The bottom drawer works fine. But the top drawer is not working properly -- it repeatedly stops in the middle of the cycle and there is water left in the drawer. Previously when this happened, we called a repairman; he removed the top drawer from the machine, said it was "off track", flipped some lever, and put the drawer back. He seemed a little embarrassed by having to charge for a service call for


Are you able to provide a bit more information on what you see when the dishwasher stops in the middle of the cycle -\015\0121 - is it displaying the time remaining in the cycle and is it always the same time?\015\0122- do you get any fau ... Dishwashers

Fisher & Paykel 2 drawer dishwasher: I too cannot get power to top drawer. 4 days ago we had an F1 code. My husband pulled out drawer, wiped up water, and dried it out. Put it back in overnight, and both drawers worked fine. Now the bottom drawer is okay, but no power to top. Help!


He might have unplugged something in the proccess of drying the bottom ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a mdd8000aws dishwasher. After a power outage (2 days) the power came back on, and the bottom drawer no longer works. It still make the chiming noise when the drawer is opened, but the control panel is not fully lit up and the washer will not start in any mode. The lights seem to flicker for a short moment and then they all stay very lightly lit up. Is this just a bad control panel or is there some other circuit that needs replaced? BTW, the top drawer works perfectly.


... Maytag MDD8000AWS Builtin Dishwasher

Dishwasher top draw DD603 has stopped. Control panel will not light up either. Have tried turning it off and back on at wall. Bottom drawer works fine. Help!


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Stops part way through programme water still in machine. Now no power to machine. Problem happened yesterday - cleaned filter and pump - power came back. Programme started but then stopped. No power - nothing happens.


Either there is a bad capacitor in the control panel, or the power supply has a faulty capacitor. You will have to get a multi-tester and test each component for resistance and current ... Dishwashers

Hello! I have a Kenmore Dishwasher Model # 665.15805890. The dishwasher came with the house and I'm guessing it is around 10 years old. My toddler was having a great time flipping the door to the soap dispenser back and forth until he pulled the door off of the pin. Now, I can't seem to position the spring in a way so that the door will spring back. I never looked closely at the hinge before, so I don't know if that is the only reason the door will not release the detergent, or if something


Hi.Please see if the diagram here can help you. Check if the spring is that indicated with nr ten in diagram. ... Kenmore Dishwashers

MY LOWER DISHWASHER DRAWER IS "GRABBING" AS I PULL THE DRAWER OUT. HAVING LOOKED AT IT CLOSER THE PLASTIC LOCKING LATCH AT THE BACK OF THE DISHWASHER(ON THE LEFT HAND SIDE)IS BROKEN.DO YOU HAVE A PART # FOR THIS PIECE AS WELL AS A PICTURE?


You can download the parts manual for the DD603H from fisher and paykel and check which latch you need. The diagrams are given in it.\015\012\015\012 ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Why does my bottom drawer continue the drying cycle indefinitely until the drawer is pulled open. At which point it stops drying?


Do you get a beep to indicate wash cycle is complete? Does the time show 00? Are the dishes hot when you terminate dry cycle.\015\012\015\012It is likely the heater unit is faulty and the right dry temperature is not reached or the heater ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I turned on the dishwasher tonight and noticed nothing was happening, but I was getting a clicking sound. I moved the dial back to off and started over. Some water went in, but then nothing happened again. I clicked forward one click at a time. Sometimes water came in. THEN WATER STARTED LEAKING OUT. I clicked back to off. After water stopped leaking, I opened the door. There is still water in the bottom. What do I do???


Hi \015\012\015\012Thanks for using FixYa. As the water is not draining and clicking is\015\012coming from the bottom so the issue seems to be with the drain pump solenoid. Usually, these issues are related\015\012to ... Kenmore Dishwashers

ASKO 1595 Dear greendude, thank you for your reply! i haven't checked the solution yet but wanted to specify: i've got ASKO 1595 and have had it for 4 years. recent year it started to mulfunction: sometimes it would stop in the middle of draining cycle and fault light would flash. this could be normally fixed by unpluging power cord, waitng for a few minutes and pluging power back again. wahat happened now is the different: dishwasher came on on its own, nowbody started it. it came on (draining


Yes have you tried what i suggested yet ... Asko D1776 Stainless Steel Built-in Dishwasher

G851 SC Plus started to trip GFI plug. Called Miele and they said there was nothing wrong with the dishwasher and the GFI was faulty. Unplugged from GFI and plugged into regular plug and it worked for a few days. Eventually stopped running. How wrong Miele was, it had everything to do with the dishwasher and not the GFI. It was only warning me a problem was coming. Appliance man came out, noticed water in bottom pan and order new pump, said seal probably gone. Came back, replaced the pump, put d


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

Karcher G2650 OH - When I start engine pressure builds up and the engine will stop- When I pull the wand handle back - I get a high release of pressure - I can hold the wand open and start the engine and it will run until I close the wand - egnine stops


Take a look at this link, I think this might solve your problem\015\012\015\012http://www.wmpcs.com/blog/?p=72 ... Pressure Washers

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

AFTER A BRIEF POWER OUTAGE DUE TO ELECTRICAL STORM THE F1 CODE FLASHES AND PUMP RUNS CONTINUOUSLY. TURNING POWER OFF ONLY STOPS IT FOR SEVERAL SECONDS. TURNING OFF POWER TO DW AND BACK ON DOES NOT RESET. I HAVE REMOVED THE BOTTOM DRAWER AND CHECKED FOR WATER, BUT UNIT IS DRY. IS THERE ANOTHER WAY TO RESET THE SWITCH?


Hi there,The f1 fault is cased by a leak on the dishwasher.It is activated when water gets to a dangerous level in the base of the appliance near to the PCB.The main reason this happens is putting cups on the drop down s ... Dishwashers

Middle and top spinners do not spin The pump is pushing water up the back delivery tube. There are no dishes in the unit and I was able to trick the door into thinking it was closed so I could watch what was happening. Or Not Happening The spinners are completely free of calcium or soap build up and both top and middle are easily spun with a finger. While the pump and bottom spinner were working, I pulled the top drawer out partially and there appeared to be a good flow of water coming out of


Hi,\015\012 Remove each spray arm and check it is clear of food particlesat the jets. The next problem may occour at the rotating joint . If the seal is not good, you can loose a lot of water out of this point.. If both of these seem reasonable ... Dishwashers

Hi i have a bosch model no sgs53e02au australia 2 weeks ago put a wash through over night woke up in morning noticed still making noise opened up the door of dw still making noise sort of brrrrr noise constant not stopping unless press botton off would turn off still had water in bottom rang company they told me to clean filter which i did found glass particules took water out with sponge clean it rang back they told me to get a piticuler tool size 20 to unscrew and pull out pump sat there unscr


... Bosch Dishwashers

The brackets that came with my LG washer to attach it to my cabinets do not keep it from falling forward when the door is down and the racks are out and loaded with dishes. Are there any other heavier duty brackets to use for this problem? I have pulled the dishwasher out on several occasions the re-bend the brackets back and re-attach. Can you help me with this problem?


... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

Hello....I ran my dishwasher as usual but it never completed and lost power. Drawers are hard to pull out and a little bit of standing water is left in the bottom. How do I get power back? Model DD605-BK


... Fisher and Paykel DD605BK Dishwasher

It has stopped working, There is power going into te machine. An engineer from Repaircare said it was the programmer, ordered a new on vcame to fit it said it was te wrong one. Ordered anoter one Whirlopool saaid it was out of stock, on back order. Waited 3 weeks engineer came with new programmer, fitted it it didnt work. Said maybe they can't fix it. Thew nachine is only two years old and a popular make. WHAT CAN I DO???


Hi,I am sorry to hear regarding the problem. You need to have some patience in order to find what's actually work with the Dishwasher. I cannot jump to the conclusion as there might be "N" number of reasons.Now, Fi ... Whirlpool Dishwashers

Leak My dishwasher Danby 22 in. DDW396 is 3 years old. Recently it started to leak from the rear. The water came out slowly from the back but I couldn't tell where the problem is - it leaks when it runs and when it stops working.


Hi there, dishwasher leaking might be due to either of these causes, check these:Main tub sealNote… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dishwasher, the foll ... Danby 22 in. DDW396 Free-standing Dishwasher

ASKO dishwasher my dishwasher came on spontaneously and keeps running first (drain, I believe) cycle. It stops when I unplug it (of course- no power) but sturts immediately when I plug it back. Error message is displayed


F2 fault water in the base remove dishwasher from under the bench and tip back water will run out,then it will restart.remove rear lower panel and run the dishwasher you may find a leak,also check that the inlet valve is shutting off and not filling ... Asko D1776 Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1014 seconds