Having problems with your Fisher and Paykel 24 in. DD603H W Built-in Dishwasher ?

F2 code. Followed listed guidance of removing assmebly and checking...unfortunately, however, my impellar has separated from the rotor assembly and the rotor assembly is stuck in the drawer. I tried to pull up on the shaft with some pliers, but that didn't work and I didn't want to pull too hard and cause damage. Please advise as to how to remove the broken rotor assembly from the drawer. Thanks


Answers :

There are no wires underneath the rotor - it is just suspended in the cavity. So you cannot do any damage except make scratches around that area. Maybe take a straightened wire coat hanger and insert from the side hole in the filter sump area. You might be able to push the rotor up to an extent and then grab it with pliers.
Repair Help & Product Troubleshooting for Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

F2 code. Followed listed guidance of removing assmebly and checking...unfortunately, however, my impellar has separated from the rotor assembly and the rotor assembly is stuck in the drawer. I tried to pull up on the shaft with some pliers, but that didn't work and I didn't want to pull too hard and cause damage. Please advise as to how to remove the broken rotor assembly from the drawer. Thanks


There are no wires underneath the rotor - it is just suspended in the cavity. So you cannot do any damage except make scratches around that area. Maybe take a straightened wire coat hanger and insert from the side hole in the filter sump area. You mi ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

I have a Briggs and Stratton power washer Quantumpower 5hp water driver series 1750 PSI 2.0 gal min model # WGV1721 . I got it used and it was always a bit hard to start but always started. Pull cord frayed and broke I bought new cord and a neighbor replaced for me. Now it does not want to do anything when pulled. I can't get top cover off that has screws with round holes instead of phillips or standard slots to get to pull cord winding


Spray well with WD-40 or similar, and take a small chisel, on it's edge, and hit hard enough to allow chisel to dig in to head of screw, making a "V" like slot in the head, then angle chisel slightly and start tapping in direction of loosening(counte ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Pressure Washer I have a Porter Cable pressure model no.PCH2401.It works fine for 5 minutes,then I can hear the motor loading down and then it stalls out. I tried to start it and it was very hard to pull on. disconnected the water supply and if was very easy to pull and started right up. I noticed the pump was very hot.This unit has a thermal relief valve on it,shouldn't it have released when it gets to a certain temperature .I was thinking maybe this is why it might be shutting the motor


Any leaks from connection at pump to gun and wand assembly if so the valve is detecting leakage and open up again without u squeezing trigger it builds up in the head.if your trigger gun is leaking internally then you will need to replace the gun thi ... Pressure Washers

I pull the Ripcord and doen not start. The ripcord feels very hard when pulling. When I remove the chamber and inspect the cord mechanism, it seems to be working fine. thanks for the Solution


... Honda Pressure Washer PSI 3000

Hi, I emailed sometime ago about my fisher @ paykel dishwasher not working. This will be the first time I've used your service and I'm just a little unsure how effective it will be. I guess I'm a just being sceptical but i really want it fixed without paying call out fees and the like. So how much do i have to pay. The top draw will not turn on. At the time the draw was hard to open so i went through the procedure to recalibrate the draw when i was holding down the buttons to get it into self t


Please confirm if you still have a problem with the dishwasher. It is unclear from the thread of your responses as the statements of the other expert will be visible only to the client. \015\012Also please confirm what you mean by "buttons stop ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Dishwasher will not fill with water. I've already checked the float assembly, that seems to be working fine. The water just doesn't seem to run into the machine. Little history on an unrelated problem: I want to mentioned that not to long ago my brother tried to put a bunch of celery through the garbage disposal. The sinks and pipes got all clogged up and we had to take them apart to clear up. Immediately afterwards the dishwasher stopped filling with water. I don't see how the two can be r


Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher ... GE 24 in. GLD5500L Built-in Dishwasher

Dishwasher Model Kenmore # 665 16829000 Dishwasher "Quick Rinse" was blinking and no other buttons would work. Received FixYa solution below: "Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow plenty of air through the two holes on either side. The holes that you need to blow air into are not on the circuit board, but on the plastic underneath the circuit boar


Hi\015\012If the control board detects that a key is stuck in the depressed position, the dishwasher operation will be suspended and the control will flash the light for that key until the condition corrected. If a key without a light is ... Dishwashers

I have a Maytag MDB6600AWW that is giving me a fit. It only works when it wants and the door is hard to operate as the handle isn't connected correctly anymore.


This is common for this type of Maytag dishwashers. Otherwise it's a very solid machine.You need to replace the door handle with switches. ... Dishwashers

Need to replace the latch assembly on Maytag dishwasher model # MDB5600AWW. How do I gain access to the area where I need to replace the part? I removed the 5 screws at the top, but can't seem to get the upper front panel off. I'm afraid of pulling on it to hard.


Remove all the screws on the inner door panel and lift it up it will be easyer ... Dishwashers

Have power to unit. sounds like it is working. pull trigger on the gun and hardly any water comes out. turn it off and there is pressure coming out


Have you tried pulling the spray nozzle tip off and checking it for blockage? The spray tips have a tiny hole for the water to pass through, and sometimes a grain of sand or debris will get stuck inside the nozzle and restrict the water flow. Somet ... Pressure Washers

I have a karcher 2.35d which doesn't want to work, it doesn't seem to be pulling any water from pump? Any ideas? X


... Pressure Washers

I have a troy-bilt 2550 psi and just use one time I put oil and gas but now It won't want start the pull cord is hard what i can do


Make sure you hold trigger in to relive pressure when trying to start ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Dishwasher 66513752K601 keeps blowing the thermal fuse. (Bi-Metal W10258275). I have replace the Thermal fuse several times. After i replace the fuse for some reason after a few months or less it will blow it out again. I have also replace the front panel assembly after it stopped working correctly. I would like to know how to test the dishwasher to find out the root cause of the fuse issue. I don't want to be replacing the fuse every time and don't have the $$ to buy a new dishwasher. Everythin


... Dishwashers

MY GE WATER SOFTENER QUIT WORKING PROPERLY AFTER 6 MONTHS ,I HAVE HAD SERVICE CALLS AT $150 EACH TO NO AVAIL IT DRAWS SALT BRINE MY WATER HARDNESS IS 17 I HAVE SOFTENER SET TO 22 .I HAVE PRE WATER FILTERS HAVE TRIED DIFFERENT SALTS ALL TO NO AVAIL, NEITHER GE OR HOME DEPOT WANT TO HELP AS NOW I AM OUT OF WARRANTY I HAVE BEEN ILL AND IN THE HOSPITAL (CANCER) THAT'S WHY I HAVE GONE OUT OF THE WARRANTY TIME MODEL GXSF30H PURCHASED 19/02/10


As you have purchased GE water softener and stop working after 6 months,then you need to check it from an expert technician and if he is able to solve this issue,then it good and well, but if this takes more money to repair and not under warranty the ... GE 30000 Grain Water Softener GXSF30H

DS603 Fisher & Paykel U1 error code ..(see our previous errors we've listed) we have now pulled out the yellow water valve that goes up behind the front panel and at the other end by removing the drawer and plastic protector thingy - we checked that there were no bedris or calcium buildup in the valves ends and filters and replaced it all. So we put it all back to gether as we could not see what would cause this error, only to find that it worked - water came into the machine but about 4 mins in


This product is total ****.\015\012Pull it out, call whoever sold the **** to you\015\012and tell the to come get it and shove it up their ***.\015\012Then buy a Bosch and live a happy life.\015\012The design is moronic. The machine is like the old\ ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

I have a Dewalt 3100 psi pressure washer which is hardly used since I bought it almost 2 years ago. It cannot start. It is full of gas and I have gone thru all the basic steps prior to pulling to start. it does not seems it wants to start.


... Dewalt 3800 PSI Pressure Washer

Opened the door of a kenmore elite 66516493300 and heard a loud bang. Then the doo fell open hard. Now when I open the door it wants to fall straight down fast. I see no springs in the parts list but assume that something counterbalances the door. Do you know what's srong and can I fix it myself? Thank you, Peter M. Bonadio


Http://www.managemyhome.com/mmh/lis_pdf/INSTL/L0408224.pdf\015\012\015\012if you look on page 24 it shows the spring and how to adjus ... Dishwashers

KUD101FKSS Kichen aid dishwasher does not work.


There are three tabs that are holding the whole assembly, accessible from the bottom...they need to come out. Only then you can remove or even move the assembly... ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hi, We have a Smeg ST 663 dishwasher that does work. However, sometimes when you want to use it and turn the power button on it beeps twice with the red light flashing and you can't get it to work or change the settings. Sometimes if we leave it for a while and try it again later it will work, but it is annoying as sometimes it won't want to work for ages and we really want our dishes cleaned! The dishwasher doesn't have many buttons on it (a power button, cycle selection button and 1/2 load


Hi,\015\012\015\012Turn machine on and press and hold the programme select button till the light goes out about 5-7 seconds see if this resets it if it does start a cycle and see what happens.Otherwise the pcb as its not responding to an ... Smeg Dishwashers

I have a dd603 and i cannot remove the rotor from the stator in the lower drawer. when i disengaged the locking ring to pull the rotor out the impeller broke off and now i cannot remover the rotor by pulling up on the rotor shaft.


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

My dishes are filled with white residue from the hard water. I've tried vinegar to cut it and new rinsing agents but nothing works. Is there a filter to clean out any hard water deposits? Do I need to check the line for plumbing for hard water deposits? My water softner is working fine, my dishes are filled with white all over them. HELP!


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

The dishwasher was recently removed for floor refinishing and reinstalled. The bottom rotor works but the top rotor does not. I asked the re-installer, who worked for the moving company, if he had connected everything properly and he said there was just one water line going into the machine and assured me he had connected it properly. Is there something else that needs to be done to make the top rotor operational? Thanks. John M


... Jenn-Air JDB3610 Built-in Dishwasher

Karcher 2400 pressure washer with honda engine. my problem is that i've installed a new rebuild kit in the pressure pump assembly, and now, when i reinstall the assembly back on the engine, i cant even pull start the engine over. its too tight! when i loosen back on the pump assembly, i'm able to pull the engine over. what have i installed wrong from the rebuild kit??


The pump is correctly oiled and lined up on the camshaft, correct? ... Karcher 2500 PSI Pressure Washer

GE gsd2350r00cs fine filter removal. Once the spray arm is removed how do I remove the fine filter? does it pop out of the back? Don't wat to break it if I pull too hard and it's not supposed


... GE Dishwashers

I have a several year old honda gx240 engine. It has never been teched and now, all of a sudden it hardly works. Before this it would occassionally backfire but now I cant put any load on the engine or get any rpm's out of it. It was literally a overnight thing. Worked perfectly the other night and now it hardly runs. Any ideas? Anyway to adjust/clean the carb?


It sounds l may need a digapham or bowl cleaning ike a carborater problem it ... Honda 8 HP Engine
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1198 seconds