Having problems with your Fisher and Paykel 24 in. DD603H W Built-in Dishwasher ?

I have a F2 flashing on the top drawer. My dishwasher is only 2 years old. It started to bip on rinse and F2 was flashing. Also water does not drain when it get to rinse. I have this problem 4 months. I have no idea what's wrong. Will it be covered by the manufacture warranty? Please help. Many Thanks.


Answers :

The motor has not
\015\012been sensed rotating
\015\012\003 Foreign object has jammed the rotor
\015\012\003 The rotor has failed
\015\012\003 The hall sensor has failed (small sensor on the underside of the motor)
\015\012\003 The electronic controller has failed
I've had the same problems and it's common with these models. Unfortunately the manufacturer won't cover because it's been 2 years. This is a problem that you'll need a technician to come out and replace the "flap" or check for a leak in the casing by removing your bottom drawer and looking inside. I would place a paper towel and see if it gets wet, then you know that there's a leak.
Repair Help & Product Troubleshooting for Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a F2 flashing on the top drawer. My dishwasher is only 2 years old. It started to bip on rinse and F2 was flashing. Also water does not drain when it get to rinse. I have this problem 4 months. I have no idea what's wrong. Will it be covered by the manufacture warranty? Please help. Many Thanks.


The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed (small sensor on the underside of the motor)\015\012\0 ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas


Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher

Bosh dishwasher SHU43C05UC won't finish the cycle. won't drain and keeps running for ever when gets to 1 min left.Hoses checked and not clogged. I was able to drain the water by doing the test run and punching the rinse and hold button .what is the problem?


Hello,Welcome to FixYa.Based on your description " won\\'t finish the cycle. won\\'t drain an ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

My Maytag Performa model # PDB3600AWE is not draining. When it gets to the 2nd half of the rinse cycle, nothing happens, no noise, nothing. Could this be a problem with the motor? It seems to run fine through the wash and rinse cycles.


... Maytag PDB3600A Built-in Dishwasher

Water problem Hi, I have a Jenn air DW 711 that does not get water. I checked the following: Water line: I unhooked the water line and it is clear & free flowing. Float: The float moves up and down as it should. Filter: The filter inside the tub is clean. The motor runs and will drain any water in the tub I put a bucket of water in the tub and the dishwasher immediately drains no matter which setting I choose. Any ideas? Thanks, Steve


Many dishwashers will drain at the beginning of any cycle. \015\012If the water does not fill after the pump-out cycle, then the problem is either the fill valve or the float switch. You should be able to hear the float switch click as you rais ... Dishwashers

Hi I am in an emergency situation with an ikea whirlpool dishwasher. I have no idea what model it is since it's built in and I can't find the manual in my rental apartment. The machine works normally until the part where it's supposed to pump the water out after rinsing. At this point it starts to beep, once, and then 3 times. On and on and on. If I open it, there is water stagnated there. If I try to turn it off and back in, it will go through a whole new program and then I get the same problem


Can you feel the pump operate during the last wash cycles? if not either theres a bad pump motor or lack of power to the pump during that cycle,if this is ok,then remove the drain hose to the main drain to see if this is plugged up with food debris ... Whirlpool GU2400XTP Built-in Dishwasher

Kitchenaid dishwasher The clean light was flashing 7 times, so I did read and try the solution SaniRinse-EnergySaverDry-SaniRinse-EnergySaverDry and this did get the machine to unlock and start up. Thank you! But I'm noticing that no watre is going into the machine. I can hear it drain some water. It is very hot and steamy in the machine so no heater problem, but I don;t see any of the soap on the bottom of the machine rinsing away. I'm afraid its stopping because the motor is overh


... KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

Our dishlex global 310 will start to fill with water and then will get to the pre wash stage, then will completley stop and start flashing rinse? I have no idea whats going on please help!


This is an error code and means the wash motor has failed & needs to be replaced. ... Dishwashers

Dishwasher quit during last part of cycle during rinse. did not drain water out. Will not turn back on. Electrical problem ruled out so power getting to washer but does not tuen on. Does it have a re-set button? Jamie


There is a fuse in the control panel that burn you need to change it +- 20$ :) ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Neff 4456 water resevoir not filling. Checked float switch and all OK. Checked water supply and all OK. Filled resevoir manually from top of resevoir and program cycle starts but stops when rinse is required.Have stripped down and cleaned switch with float switches as I have had that problem before getting clogged. Any ideas


... Neff 24 in. S4456 Built-in Dishwasher

Model #MDB7130AWB Stops mid wash cycle at roughly 60-65 min left, water will not pump out. It sounds like it is about to pump out but doesn't and keeps doing this repeatedly. Using the 8 minute rinse cycle, it drains with no problem...any ideas?


... Maytag MDB7130 Dishwasher

Hi i have a Candy CDI 1012/B Intergrated dishwasher and 4 lights are flashing during the first programme then system drains and stops showing four lights lit. We have no instruction manual or service manual this would be good to get hold of as we have serveral of these machines. any idea what the problem is to save us time investigating it. Thanks Paul


Hi. The four leds flashing quickly at start of the cycle means that there is an inlet problem. Check that the inlet hose is not bent, blocked or kinked, ensure that water has sufficient pressure. The inlet valve can be tested reading Ohms at valve te ... Dishwashers

I have a Whirlpool Gold Quiet Partner III dishwasher. When I unload the "clean" dishes, there is some type of film or crud on the dishes. I have to hand wash them to get this off. It seems like a lint-type trap might be backing up and then not rinsing the dishes cleanly. Amy ideas what might be the problem? Thanks


You need to check the drain system completely, look for plugged screens, pump impellers, valves and the drain hose. You need to witness a large volume of water flow during drain. ... Whirlpool Dishwashers

Bosch dishwasher problem -water comes out the air vent and gets all over my counter. Filter in Bosche is clean. Plumber out yesterday and said tube to vent is clear and he checked where the dishwasher hose connects to drain - all clear. Any ideas???


... Bosch Integra 800 SHX98M05UC Built-in Dishwasher

Control Module? I have a GE Profile that seems to have a control module issue. I've changed the module and it continues to do the same thing...won't drain at end of cycle and begins washing right away after selecting new cycle. Washes for only about 5 minutes total and then just heats the water...soap dispenser doesn't get rinsed clean either. Any ideas?


... GE 24 in. PDW9880LSS Stainless Steel Built-in Dishwasher

How do you stop the water not draining. I ran the DD603 last night and this morning found the drawer still containing the rinse water. Obviously everything was wet. I do NOT want to call out an engineer. They are hopeless and do not solve the problem, merely get the machine operational again without solving the root cause.


If the water doesn't drain from your dishwasher, check these:\015\012\015\012Drain line/air gap--A clog in this part is the usual\015\012reason that a dishwasher doesn't drain. Remove the drain line to clear\015\012any debr ... Fisher and Paykel Dishwashers

This dishwasher (MAYTAG DWU6402AAE) is 12 years old, and recently started having a problem with the water. I'm not convinced it's spraying or even rinsing. The soap doesn't drain from the container. Dishes are not getting clean. I'd like to know if there's anything I can do to fix this before I call in a repairman. I'm very handy, and can follow instructions. Thanks. Mike


DWU700BAXSoap dispenser does not open during wash cycle. Kace removed ans cleaned pupp and filter also center nozzle which did have some paper specks but is now clean ... Dishwashers

Hi! Our Kenmore Ultra dishwasher is about 11 yrs old. Recently started overflowing onto the floor. Seems to be worse with soap, less when just water. Is this a problem I need to get a repairman or just use less soap? Checked the drain cycle - pump seems to work fine. Any ideas would be appreciated! Thanks AM from Portland


Try a gel and use less soap at first as an experiment they clean better and leave no film I/E electra sol gel ... Asko 24 in. D3250 Built-in Dishwasher

Hi ,my hoover hed 6612-80 dishwasher will not empty on a wash cycle but will empty on a pre rinse any ideas what could be wrong? could it be a pcb problem and what sort of price should ipay to get it fixed?


... Hoover Dishwashers

Integrated Bosch 9000 127 310 (8602) dishwasher. Problem: Although it operates correctly it has just started to make a loud hum during the washing and rinse cycles. It goes quite when draining. Any ideas?


... Dishwashers

Maytag MDB9150AWW model not getting wash water, gets rinse water


Hi,\015\012I think you have thought this through throughly and have narrowed it down pretty good....\015\012The soleniod valve does work or you would not be getting rinse water...\015\012The float is working or the rinse would eithe ... Maytag 24 in. MDB9150A Built-in Dishwasher

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

Several people have posted this problem with the Frigidaire Ultra Quiet 111, but I have seen no solutions. When it is set to wash without extra heat, it cycles normally. But when the extra-heat wash and extra-heat rinse are selected, then it gets stuck first mid-wash at the 7 o'clock position, and if it is manually advanced then it gets stuck again during the rinse cycle just before the 9 o'clock drying position. Both the wash and rinse thermostats have been replaced without solving the problem.


Hi,\015\012\015\012I know that you are going to think that this is dumb... but the only thing that it can really be is the timer....\015\012\015\012 ... Frigidaire 25 in. FDP750RC Free-standing Dishwasher

I have a magtag quiet 100 series that has a broken handle but still shuts tight and seems to lock yet. Problem seems to be that the rinse only light will stay on for quite a long time and won't let me hit the wash button. When the rinse only light does go off, if I hit the wash button it starts but then switches to rinse only. Sometimes I can get lucky and get it to stay on wash after the rinse button is off for some time. Any suggestions?


... Maytag 24 in. DWD1500A Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1746 seconds