Having problems with your Fisher and Paykel 24 in. DD603H W Built-in Dishwasher ?

Bottom draw displaying U1 error message - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


Answers :

There is no water coming to the drawer.
\015\012
\015\012This could be due to several reasons. The tap must be on as I presume the top drawer is working.
\015\012
\015\012Could be one or more issues like Inlet solenoid,controller problem, impeller arm not rotating or rotor not sitting properly.
Repair Help & Product Troubleshooting for Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bottom draw displaying U1 error message - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


There is no water coming to the drawer.\015\012\015\012This could be due to several reasons. The tap must be on as I presume the top drawer is working.\015\012\015\012Could be one or more issues like Inlet solenoid,controller ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

F2 error on bottom draw screen - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

F1 error code on both dishwasher drawers. - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


Unit is in flood protection mode (caused by leak), can be cleared by removing bottom draw and drying the residual water around and under the Rfi/flood sensor board. This problem is usually caused by iether the support that suspends the wiring and hos ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Dishwasher error have a fisher paykel ds603i, top draw is receiving an error, constantly beeping with red light showing, bottom drawer is running


The error was a flood fault, water was not draining from either of the drawere, I removed the bottom drawer, dried drip pan and used hairdryer to dry fault sensor, the dishwasher then reset itself and works fine. ... Fisher DS603W / DS603B / DS603I Dishwasher

Displays code f1 and beeps - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


This means the flood switch at the base of the dishwasher has turned on.\015\012The usual cause is that moisture has collected at the base. Extend out the bottom drawer as much as possible and use towels and hair dryer to dry out the base. Make ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

F6 error message on led screen and leaking - Fisher and Paykel 24 in. DD603MFC Built-In Dishwasher


... Fisher and Paykel 24 in. DD603MFC Built-In Dishwasher

What is f4 error - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


F 4 means there is a faulty temperature sensor or heating element.\015\012\015\012Usually this needs replacement of the heating element or the controller as the temperature . ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

F2 error code? what does it mean? - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


The rotor at the base of the drawer is either faulty or there is a blockage in the rotor cavity.\015\012\015\012Need to take it out and clean the cavity first. If no difference, then need to replace it. Costs about $50. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

My dish drawers are displaying a F1 alert. - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Error code u9 - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

F4 Error Message DD603J - Fisher and Paykel 23 in. DD-603 Built-in Dishwasher


... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Bottom draw noise - Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher


Usually means rotor or motor is getting ready to fail ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

F4 ERROR MESSAGE AT HEAT POINT OF WASH CYCLE - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


F4 fault is a a heat sensor problem,\012\012\012http://www.retrevo.com/support/Fisher-&am ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

How do we remove both draws of DD6031 - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


Hello,This repair is simple. Open the door and on the lower front corner you will see a tab depress and push the rack forward. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

Fisher and Paykel Error code Ho - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi the top draw of my fisher & Paykel 2 draw dishwasher is displaying an F2 with a spanner display, can you please help. Vicki


Hi Vicki.F2 means that there is a problem with the rotor attached to spray arms on one side, and to impeller pump on the other. The electronic control detects rotation thanks to a hall sensor located at the base of the rotor. If rotation ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Our 2 drawer Fisher and Paykel dishwasher is automatically starting its own washing cycle (well, motor starts, but no water appears to be entering), then it shows F1 error message and a spanner icon flashes. Within 30 secs of this occurring on one drawer, this starts on the other drawer. Only way to stop is to switch off at power socket. Any idea what the error message is telling me?


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Fisher and paykel DD603 has no power - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


If both drawers have no power and the mains supply is ok, then the power filter board at the base of the dishwasher (under bottom drawer) is faulty. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Fisher Paykel DD602 removing bottom drawer - Fisher and Paykel 24 in. DS603H I Built-In Dishwasher


You can view the following video to check how to take the drawer out. The steps are shown half way into the video. Make sure the mains plug is pulled out from the socket before w ... Fisher and Paykel 24 in. DS603H I Built-In Dishwasher

Excess water in fisher peycal dishwasher - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Dishwasher pump not strong enough - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Dishwasher is leaking when on - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


Hi,Here is a tip that I wrote about leaking dishwashers ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

I have a Fisher and Paykel DW60CDX1 dishwasher, the display originally came up eith an error code for the door, which seemed to be the problem as it restarted with some pressure on the door, then it stopped again and now there is no LCD display and no action, cycle butten lights are on but will not make a noise when pressed. We live in the bush and cannot get a easy service option. Is there a diagnostics mode I can try, although the LCD may not work?


Old question, but for anyone else, hears the answer - http://www.recalls.gov.au/content/index.phtml/itemId/1015047This model has a product recall, minehas done the same as described above, recall issued Aug 2012. ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

Is there a reset button on the dishwasher for the Fisher Paykel DD 605. I washed a top and bottom load, nothing unusual about the loads. The dishwasher just stoped and there is no power on either of the display panels. It washed the dishes but did not drain both tubs and the doors are real hard to open. Help!


If there is no power on both the drawers then 2 things\015\0121. the circuit breaker on the mains power supply feeding the dishwasher has tripped\015\0122. the power board that feeds the drawers is faulty. This is located at the base unde ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2067 seconds