Having problems with your Fisher and Paykel 24 in. DD603H W Built-in Dishwasher ?

I have a fisher & paykel dishwasher. It has 2 drawers and the top drawer is stuck. It will open if I force it, so i'm using the bottom drawer. It just recently happened. Is it hard to fix?


Answers :

The lid seal of the top drawer is broken or has come off. To get to it you will have to take the two drawers out carefully along with the cables and hoses intact.
\015\012
\015\012Then feel the top underside of the cabinet for the lid seal. Depending on the problem it will have to be replaced. There is an intricate mechanism of actuator arms and motors that drive it. I hope these are ok.
\015\012
\015\012If you are lucky maybe the drawer has just come off the rails and you could put it back and it will be ok.
\015\012
\015\012Please rate this solution if helpful otherwise drop a comment
Repair Help & Product Troubleshooting for Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a fisher & paykel dishwasher. It has 2 drawers and the top drawer is stuck. It will open if I force it, so i'm using the bottom drawer. It just recently happened. Is it hard to fix?


The lid seal of the top drawer is broken or has come off. To get to it you will have to take the two drawers out carefully along with the cables and hoses intact.\015\012\015\012Then feel the top underside of the cabinet for the lid seal. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

I have a Fisher and Paykel dishdrawer model ds603. Not sure eactly what happened but my son says that the cycle stopped last evening (and only tells me this morning!). Dishes though appeared to be clean and there was a small amount of water at the bottom. I tried opeing the washer and it was hard to open as though the drawer was stuck on something. I removed the drawer and checked the rollers and they are fine. I realised then that the drawer is getting stuck on the inside lid that provides the


The best thing to do is to remove the rack,drawer completly,and close it up,see if it will come on,and run all threw the cycle.If it does,then put the rack,drawer on the track.The rollers could be,well,not snapped all the way on.It will be in that ar ... Fisher Dishwashers

Drawers Stuck I've had my dishwasher for a couple of years now. All of the sudden the drawers are extremely difficult to open. I have to use all my strength to pry open the drawers so I can get the dishes out.  It started out as only the bottom drawer having the problem and now both drawers are having it.  It seems to be running fine because the dishes that were in the drawer before it got stuck were cleaned.  And there is nothing blocking the drawer from opening.  It seems like the seal that c


I turned off the electrical breaker for about 8 seconds and it rebooted itself ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

My Fisher and paykel dishwasher drawers are showing a F1 fault on the top drawer screen, But it was the bottom drawer that was in use at the time of the fault occured. The top drawer will open but the bottom drawer is locked. I need to unlock this drawer to get my cooking equpiment out. Please Help. I know that the F1 fault is a flood fault but how do fix it.


... Fisher and Paykel Dishwashers

Although we never use the drying option, the right side of both top and bottom racks, in front are rusting due to loss of plastic edge. We hardly ever even use the dishwasher. Why would this happen?


... Kenmore 13859 / 13854 / 13852 Dishwasher

Recently our GU1100XTLQ1 started having a problem. It barely cleans the bottom rack, and barely gets top rack wet. The soap stays stuck in the dispenser. I can't see inside as it runs, but my guess is that not enough water is being shot out of the various spinning arms. From looking at diagrams it would appear that this dishwasher uses a pump to circulate water from the bottom of the cavity through the spinning arms. Is my problem a dying pump?


... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Cloudy Dishes My dishes have just recently started turning cloudy with white fllm. This has never happened before and the dishwasher is approximately two years old. There is no issues with hard water, and have used Jet Dry, have tried cleaning it with bleach and vinegar, and have used soap and no soap. Please give me suggestions as to why this would start occurring now. I took off the inside panel and it was full of all kinds of gunk which I since cleaned out. I would like to know how to avoid t


There is a new product out that filters the water going into your dishwasher. the film or cloudy white look is caused by hard water. this filter eliminates the problem and is very affordable. you can get it at dishwasherfilter.com. i was amazed how c ... Dishwashers

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

Intermitttent beeping on bottom drawer of dish washer no error code only cycle to work all the way through is rinse cycle. Have turned off power supply over night did not fix problem. When you press pause button restarts for about five minutes then beeps again. No problem with top drawer. All inside cleaned using correct powder and rinse aid.


Panel control board Call Encompass Parts 1-800-638-3328 ... Fisher Dishwashers

Wont drain the water in my fisher and paykel 2 drawer dish washer but only in the top unit as it was used a lot more than the bottom one. i suspect it is the pump - any ideas and how hard is it to replace?


Hello- Try swapping rotor - the blue bladed thing at bottom of drawer - from top to bottom. If it works, then replace with new part. Let me know if this info helps- have more if needed. Thanks- Ed ... Dishwashers

Bottom Draw is hardly used and will not start, code F2 - motor problem comes up on panel. How do I fix it


F2 error code ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My ariston lsv 66 dishwasher will not start washing cycle. It makes the pumping noise as it normally does at the start of the cycle and some water enters the bottom of the machine but then it stops. I have checked to make sure that there are no leaks so the problem is with the filling up of the machine. I live in a hard water area and haven't used anything to help reduce the limescale so expect this to be playing a part. I have tried all the washing cycles but the same thing happens. Any advic


HERE I AM I LIKE THIS JOBE\015\012 PLEASE CHECK THE WATER INLET FILTER I FEEL FROM YOUR DESCRIBE IS IT\015\012 YOU NEED TO CLEAN IT BY ASMALL BRUSH >\015\012 THANKS ... Dishwashers

Hi - bought this dishwasher 1 year ago yesterday (it figures). Discovered last night that it hadn't drained properly the last time I used it (maybe 5 days before). There was about 2" of soapy-feeling water in the bottom of the cabinet. I put it through another cycle and the same thing happened. I only run it maybe every couple weeks. Can you tell me how to fix it?


Hi,Let me offer you a solution in 2 parts. A generic one needs you to investigate each and every aspect from Point 1 till End :-\015\012\015\012\015\012\015\012\015\012Drain line/air gap\015\012\015\012A\015\012clog in ... Dishwashers

WE MOVED IN OUR HOME 17 YEARS AGO. THE GE POT SCRUBBER DISHWASHER HAS ALWAYS WORKED VERY WELL. RECENTLY IT STARTED TO LEAK UPON USE. FIRST OUT OF THE BOTTOM IN FRONT, ALL OVER MY FLOOR AND THEN IT STARTED TO LEAK THROUGH THE FLOOR AND I CAN SEE IT DRIPPING FROM THE CEILING IN OUR BASEMENT ? SHOULD WE GET IT FIXED OR WOULD THAT BE TOO EXPENSIVE?


If your dishwaher is 17 years old I would say it probably should be replaced. ... GE Dishwashers

Gritty Dishes My dishwasher is an indesit D4200 and is leaving a gritty film on all my dishes - it cant be the tablets because i have to use Fairy. I have cleaned it from top to bottom and put a cleaner tablet through. I live in the highlands so it cant be a hard water problem. any ideas? im really stuck! Thanks


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

We just purchased a used Fisher and Paykel DS 603-i. After installing and running the normal cycle there was a lot of water left on the bottom of each drawer. We ran the bottom drawer (water stil siiting on the bottom of the top drawer) and part way through the main wash cycle we got what I think was a F1 error code (we do not have the LCD version but the Rinse light was activated). I took out the bottom drawer, dried out the basin and then took out the washer and reattached the drainage pipes t


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You’ll need to reset it by poweri ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

I have a F and P 603 dishwasher with a similar problem as to a recent post here. My top drawer doesn't turn on and my bottom drawer does. Well it just has after I swapped the "blue" motor inside from my top one. Now, I have tried and opened as far as the translucent "X" plastic from the bottom of my bottom drawer showing the motor and it looks fine. I have even swapped the control board from my top drawer to try and see if it works and it actually does. So, problem persists. Top drawer do


Alright, open up the outer panel of the machine. Note the positions of the wires on the switches and\015\012remove them, unclip the switch housing from the base panel. The\015\012switch housing contains one switch for each drawer. The switches are\01 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have the two drawer model dish-drawer system. In the past the top seal leaked and since has been replaced with a new seal. Worked well for several years after but then the top drawer quit running. So we started to use the bottom drawer. That was fine for awhile althought it would pump waste water into the top drawer. Now neither drawer will work. The bottom drawer starts up and shuts down. I pulled the lower drawer and it is dry.


If your model has got an LCD display are you able to record what shows up on the display when the bottom drawer shuts down. If no display then are you able to note down the LEDs which are on inside the top of the drawer lid. It is likely there is no ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have F1 flashing on my dish drawer....turn it off a couple of months ago because of the same issue and have not used it since....turned it back on and used the bottom drawer...all OK...went to use the top drawer again and the F1 returned??? please help


Please confirm if the F1 on top drawer shows up immediately you press the Start button or part through a wash cycle? What happens when you turn off the power and back on. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

The bottom drawer is filling with excess water after the top drawer cycles. It doesn't hamper the use of the bottom drawer as the excess water drains during the cycle, but I am concerned about rust, etc. from the excess water standing in the drawer. Please advise. Denise Arnold


Hi\015\012 \015\012This means that you have an overflow leak problem. You need to shut off circuit breaker or pull fuse. Next let it dry out for up to 4 days ,peak under dryer and feel metal drip pan and ... Fisher and Paykel Dishwashers

The dishwasher won't start, its stuck, pots/pan button is blinking, & the timer has (2)_ _ bars blinking. I tried to reset/pushed the start/resume button nothing happened. I pushed the cancel/drain button still nothing happened. I close the door tight..nothing. I check the trays if there something stuck inside..nothing. I unplug/replug the power cord nothing? my wife was using it when this got stuck about 3 weeks ago.


Did you hold the start/resume button for at least 3 seconds if this works the dishwasher will start ok but if there is a fault it will fail again best you contact your nearest service agent good luck ... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher makes knocking sound during rinse cycle. Unit is empty with no obstructions. Even switch the spray rotor from bottom to top drawer. Did not fix knocking sound. Top drawer makes the sound. The bottom drawer is silent. Any help appreciated. Thanks, Pat


Http://www.jordansmanuals.com/ServiceManuals/FP/Dishwasher/DW60CDW2/DW60CDW2%20Parts%20Manual.pdf\015\012\ ... Fisher and Paykel DD605HSS 23 in. Built-in Dishwasher

After running our dishes through a wash cycle we noticed there was still a lot of food stuck on the plates & glasses etc. We cleaned out the trap but due to the murky water in the well, we also pulled out the racks & removed the bottom plate. The underside was greasy and had a lot of grim stuck to it as well as the bottom of the drawer itself. We washed the filter trap, swing arm and plate in the sink. We loaded it with the dishes that previously did not come clean and ran a full cycle. The


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Re: Creaftsman 2700 psi washer, model 580.752100 - I cannot use the detergent cleaning tank. The pump forces water into the tank, and it overflows onto the ground. If I try using the washer with the detergent shut-off value in the off position, the water pressue forces the valve completely out of the housing. Is there a simply fix for this or time for a $ervice call? sw


... Craftsman 2700 Max Psi Pressure Washer 23 Max Gpm

I have a Kenmore Ultra Dishwasher. The bottom arm spins, the top doesn't, although water drips out. The water fills up under the heating element. The top dishes aren't getting clean and the bottom aren't as clean as they used to be. I also noticed that the soap dispenser is open, some of the soap is gone, but there's still some soap in left in the dispenser. This never happened before and it happens all the time now. Thanks for any help you can give me!


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1235 seconds