Having problems with your Fisher and Paykel 24 in. DD-602 Built-in Dishwasher ?

Fisher & Paykel dishwasher model dd602 error code F4

\015 Need Temperature sensor and service manual.\015

Answers :

Hi there,\012
It means your filter is dirty. Remove metal plate at bottom & scrub with a toothbrush. Clean arms as well.
Clean all around the door & pull out the lift out filter, scrub clean with a toothbrush.

Repair Help & Product Troubleshooting for Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Fisher & Paykel dishwasher model dd602 error code F4


Hi there,\012It means your filter is dirty. Remove metal plate at bottom & scrub with a toothbrush. Clean arms as well.Clean all around the door & pull out the lift out filter, scrub clean with a toothbrush. ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Fisher Paykel Dishwasher model # DD603, started up by itself, was shut off and it started up by itself again, kept doing this over and over until being unplugged, now it is flashing an F1 error code


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

ERROR CODE F1 MODEL #DD603SS - Fisher and Paykel Dishwashers


... Fisher and Paykel Dishwashers

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

Error code. Fisher and Paykel Dishwasher


Well since you asked on the 5th July, and no reply, doesnt look like you may get one. I thought thats what this site was about?? ... Dishwashers

Fisher and Paykel Error code Ho - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Code u1 fisher& paykel model 920 - Fisher and Paykel Dishwashers


Hi, this tells you everything you need to know about a \015\012 fisher& paykel model DW820 and DW920 modelsi was also looking for the u1 error, and im sure my problem is being a male i use to much detergent (powder) that creates extra foam ... Fisher and Paykel Dishwashers

Fisher Paykel Dishwasher Door Open error code


If it is a dish drawer type there is a clip at the rear of the drawer that holds the drawer closed. you will need to withdraw the drawer partially to look in. with the drawer open the fingers should be facing towards you. If not you will need to reac ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

F4 error fisher & paykel nautilus dishwasher sometimes this error comes up and it seems to occur about 10 minutes from the end of the cycle. it doesn't happen all the time. the user guide does not specifically address this error code.


F4 is a heating error- dishwasher has not reached temperature in allocated time. If intermittent fault, problem is usually with electronic board, which has temperature sensor attached. Sometimes the wiring to the control board burns out and can give ... Fisher Dishwashers

Fisher & Paykel dishwasher drawer won't run, beeps F2 error code


Craig, we had virtually the same situation.  The repair man  came and it took 2 minutes to fix.  The problem was that the bottom drawer had not been used for a couple of years and thus the impellor had jammed.  to fix it take out ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

F1 Error code on fisher paykel softouch dishwasher


F1 means that water is in your basepan--- you can pull the bottom\015\012drawer out and soak up the water with a towel... you will have to use a\015\012hair dryer to dry underneath the control sensor in the back left corner. ... Fisher Dishwashers

FIX F1 FAULT CODE ON FISHER PAYKEL DISHWASHER MODEL DD603


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

F1 error code on both dishwasher drawers. - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


Unit is in flood protection mode (caused by leak), can be cleared by removing bottom draw and drying the residual water around and under the Rfi/flood sensor board. This problem is usually caused by iether the support that suspends the wiring and hos ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Error code 888 fisher & Paykel dishwasher - Dishwashers


... Dishwashers

My fisher and paykel dishwasher drawers is giving me an F1 error code, won't stop running and is acting like it's possessed.


... Fisher Dishwashers

U3 error code - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


Error code U3 could mean the drain pump could be blocked.Remove the trays and the impeller arm. Empty the water with small container or towel. Open the filter plate and drain filter. Get the motor out and check the cavity for any rubbish ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

F2 Error code beeping - Fisher and Paykel 23 in. DD-603 Built-in Dishwasher


Your pump has seized.To check remove all the dishes followed by the grey dish wrack wedged in the bottom. Lift off the plastic spray arm to reveal a grey plastic ring around the outside of the stainless mesh, and you will also see the blue plastic im ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

I have a Fisher & Paykel Model #DD603 double dishwasher it is coming on with a code F1 with a little wrench Whats going on ?


An F1 fault means that the Mains Filter board on the bottom pan has detected water, a leak. There are, unfortunately, a few possibilities of the cause of this. Most likely it is bad lid motors (the motors that lift and pull down the lid to seal ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

My Fisher Paykel dishwasher is model #DD6051. After about 1 1/2 years, the top drawer is not filling with water. The fault code looks to be U1. The bottom drawer fills and runs fine. Would you have any idea what the issue might be? Thank you very much.


Hi,Unplug the Washer for Few Minutes, say 30 minutes and then Turn it ON. If the problem Persists, then read :-U1 Heavy and Rinse LEDMachine has failed to prime with water within approx. 3 minutesReason ... Fisher and Paykel Dishwashers

Error code F2 - Fisher and Paykel 23 in. DS603H W Built-in Dishwasher


I'm sure this is pump out problem,water not draining out. ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

We are now getting a U1 error code on a Fisher and Paykel Nautilus dishwasher which was in the house we purchased 3 years ago and has functioned perfectly until now. There was no manual left when we took over the house. We would appreciate any help you can provide.


U1 means the unit has failed to prime with water within 3-4 minutes. \015\012Its taking longer than expected to fill with water. \015\012Check the fill valve, water supply problem, excessive sudzing.,reduce your detergent. ... Fisher and Paykel Dishwashers

Fisher & Paykel DD602 Dishdrawer: F4 code - Dishwashers


An element fault (disconected or faulty controller) ... Dishwashers

F1 Error on Fisher & Paykel Dishwasher - Model 920


Your dishwasher is in flood protection mode. feel free to live chat if you'd like me to talk you through the repair cheers ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

I am getting an F2 error code on an DD603. - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


There is something jamming in the rotor , lift the spray arm and try spinning the blue fan , or if u havent used the btm drawer in ages it is a seized rotor , around 80 $ to buy new ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi My Fisher and Paykel Soft Touch dishwasher on a daily basis shows the error code F5 and beeps until I pull it out from the wall and turn it off and on again. How can I fix this?


There is no f5 fault in any of the soft touch f7p dishwashers, sure its not something else whats the model no , i fix f&p for a living ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2347 seconds