Having problems with your Fisher and Paykel 24 in. DD-602 Built-in Dishwasher ?

Its a DD601 Model and it has F4 in the window and stops working after 60 mins wash?


Answers :

Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks for using FixYa. Error F4 in your fisher\015\012& Paykel dishwasher occurs when no temperature increase has been detected\015\012for 2hrs while the unit heating element is turned on. The issue seems to be\015\012with a bad element, bad wiring harness and/or the control board itself has gone\015\012bad. To start with you’ll have to check the element, temperature sensor and if\015\012they appear fine then check the electronic control as this is responsible for\015\012supplying the power to the element. Please do accept the solution if the issue\015\012is resolved or post a comment for further assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Its a DD601 Model and it has F4 in the window and stops working after 60 mins wash?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Error F4 in your fisher\015\012& Paykel dishwasher occurs when no temperature increase has been detected\01 ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

I have a Kenmore Ultra Wash Dishwasher model # 15951,it will be working fine then just stop working it will have no power at all.I leave it for a 2 days and starts right up , works for week then stops.


... Kenmore 24 in. 15932 Built-in Dishwasher

My deceased parents have a GE dishwasher (don't know the model number - can't find it on the machine and can't find the paper work) that stops working shortly you start it and displays a message on the front panel that says "Blocked wash arm - check for wash arm obstruction - restart". We restart it and get the same message shorty thereafter. This happens when the washer is COMPLETELY EMPTY, even when we remove the bottom rack. It first started after several month of inactivity. We'll just t


Could be false sensor input, could be that the arm is not turning, I am not sure how old your machine is, but age could play a part if the arm is "in fact", not turning. If you are not mechanically inclined, I would suggest that a qualified repairma ... Dishwashers

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

MODEL#MWX233RES5 - Serial # XC: grinding noise in wash mode; has stopped working in wash mode- just a click when activating, but will work in spin mode while still grinding


HI. Ok, here the deal here; Your transmission will lock up soon. If it is not moving at all in agitation mode, it is already semi-locked, in a way. Frigidaire dose not sell the gear kits for this unit. with that said; i would inspect the hub to be su ... Frigidaire Dishwashers

My Frigidaire model GLD2155RDC1, installed in 2007, stopped working after we lost power. When we flipped the circut breaker back on the lights for Air Dry and High Temp Wash started blinking, but none of the other buttons work and when we open the door these lights stop flashing and there is no power for our machine. We tried tripping the breaker a few more times and it kept doing the same thing.


... Frigidaire Dishwashers

I have a Kenmore Elite Ultra Wash HE. Model #66513122K701. Serial #FY0310281. Purchased New 1/31/09. It only works for a full wash cycle on on 1 hour wash. Super Wash and Normal wash both stop mid cycle and leave dishes sopping, dipping wet and with green light blinking. Been doing this almost its entire life...has ahd control panel replaced once under warranty...but if it is a factory defect...they probably just repaced it with another defective part...what to do? What should I do.


... Kenmore Dishwashers

Hi, I have a Dishlex dishwasher. It's an electronic model, from about 92 I think. The model I thought was B8557WW. It is very hard to see the model number because it's almost washed away. Is the model number maybe located anywhere else on the machine? Could there be a manual or circuit diagram hidden somewhere on (in) the machine? The fault is that it wont start. It reacts to some of the front buttons, and beeps, but not all, and not the start button. Before it stopped working completely, some o


... Dishwashers

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

I have the Bosch SGS43A2GB27 Dishwasher. Today suddenly it has stopped working. 1st problem i faced was that water was coming out from the dishwasher. Then i cleaned the filters . Then i restarted the dishwasher again. Now the problem i am facing is that the dishwasher is not workign. Whatever cycle i put....the time remains the same. If i put econoy wash...nad time is for 40 min. It stays for 40 min even after 20 min. Please help . I recently called a technician...culd not afford technician aga


... Dishwashers

Hi , i have westinghouse dishwasher model SB915SJ. when i put it to wash on eco normal, it stops a after about 20 minutes and i have to press the program button to start it working again. it's currently running now but it stops about every 4 minutes and the numebr 20 appears in the display screen. if i push the program button it will rung for another 4 minutes then stop, start beeping and the number 20 appears. how can i fix this?


Www.westinghouse.co.nz/...westinghouse/.../NZ_WH_Dishwashers_May06.pdf \015\012\015\012\015\012\015\012Above is your user manual, and below is your service and repair manual.\015\012 ... Westinghouse Dishwashers

Dishwasher motor sounds like its struggeling to run. oR LIKE it's bogging down during washing cycles any and all cycles. there is water going into the washer but when washing it sounds like there is no water moving around creating the motor to work harder ........sounding like its gonna stop at any second. frigidaire d/w model#= FDB510LCS3 SERIAL==TH74378818


Try pouring water from the front. The pump has got air traps inside. This will ease your problem.Also check whether the spray arm turns freely without any obstacles. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

It does not complete the cycle. It stops working after 90 minutes without completing the cycle. Cycle should be 115 min. according to manual. Washing light is flashing but it does not continue washing. A huge amount of water remains in bottom.


... Haier HDC1804TW Dishwasher

I have a 4yr old Smeg freestanding dishwasher. Model is DF612SDX. The problem is that a wash cycle will start but about 15 mins in it stops and 2 of the programme option lights (on the left hand side of the programme options), start flashing. If you open the machine the soap dispenser has failed to open. This problem has been a bit of a slow deterioration as we've had a number of washed that have managed to finish and then noticed that although the dispenser has opened it must have been to


... Smeg 24 in. DWF612SS Free-standing Dishwasher

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

Kenmore Elite Dishwasher, model 665.15914 , blinking lights Lost power yesterday... Dishwasher ran from No 99 to 76 and stopped I tried resetting on panel....didn't work Took out fuse and put back in ..didn't work hit Normal Wash and light just blinks


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

The model is a Whirlpool # du1055xt5q3 I received infomation on how to get the clean light to stop blinking. I pushed the NORMAL WASH then HEATED DRY buttons in sequence and that worked, now it is doing the same thing and that doesn't work now. The light blinks 7 times at a time.Can this be fixed ?


Hi,The blinking always refer to a certain problem. 7 times blinking refers to defective heating element or control board.USUALLY 99% PEOPLE HAVE FAULTY CONTROL BOARD. YOU WOULD BE LUCKY ENOUGH IF YOU WOULD ESCAPE.R ... Dishwashers

Built in model MDB5601AWB- about 3 years old. The touch panel stopped working..no lights would come on when touched. Tried it a couple of days later. Lights came on..finished a cycle. after satying in the wash mode for a few hours. Then lights started flashing on and off. At that point I shut it off at fuse box since I couldn't get lights to stop blinking and haven't trusted to use since


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. From what you have described it seems to be the ... Maytag Dishwashers

We have a Maytag MDW700EDWG washing machine and it has stopped working. The display window is showing F2 and will not go to the time lenght of any program. I am unable to switch it off at the Start button. It is making a noise as if it is trying to do something - but then stops. I have cleaned the filters, checked water supply but still have F2 showing. Please can you shead any light or let me knoiw what to do Many thanks Emma


Is it the salt reservoir that is empty?\015\012Did you solve it already...mine has the exact same issue now ... Maytag Dishwashers

I have a Kenmore Ultra Wash model 16879. After setting the dishwasher and going to bed I woke up to find the "Quick Rinse" light flashing. I am unable to get the light to stop or washer to work. I tried some of the "code" combinations I saw offered on fixya but I do not have a heated dry button, and cannot find another combo that works. Thank you for any tips you can provide.


1) Crack the door open.2) Within 3 seconds press the \015\012following sequence - Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy \015\012Saver Dry3) Close and latch the door4) \015\012Press the cancel button (the circle with ... Dishwashers

Kenmore dishwasher model # 587.15103800 wash cycle won't start. It fills with water and stops. A few minutes go by and it drains. Motor is working. Any ideas why the wash cycle won't start?


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Kenmore dishwasher model # 587.15103800 wash cycle won't start. It fills with water and stops. A few minutes go by and it drains. Motor is working. Any ideas why the wash cycle won't start?


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

My Kenmore Ultra Wash Dishwasher model 17731 stopped working mid wash I checked the power cord and it is fine but the unit doesn't seem to be getting power. Is there a fuse in this thing? Any advice would be welcome.


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1149 seconds