Having problems with your Fisher and Paykel 24 in. DS603MFC Built-in Dishwasher ?

Had the double drawers for 3 years now and all of a sudden, the top drawer is having problems. A few minutes after I start a load, the blue light on the front starts blinking red, it beeps, and when I open the drawer, it is set on heavy and eco (when it was originally set on just normal). I have to turn the unit off and then back on for it to start up again and continue its cycle. What's going on?


Answers :

First thing to do is to take a clean damp cloth and lightly wipe the grime off the drawer lid especially on top of the membrane keys.
\015\012
\015\012Wonder how often it has gone into this blinking red state.
Repair Help & Product Troubleshooting for Fisher and Paykel 24 in. DS603MFC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Had the double drawers for 3 years now and all of a sudden, the top drawer is having problems. A few minutes after I start a load, the blue light on the front starts blinking red, it beeps, and when I open the drawer, it is set on heavy and eco (when it was originally set on just normal). I have to turn the unit off and then back on for it to start up again and continue its cycle. What's going on?


First thing to do is to take a clean damp cloth and lightly wipe the grime off the drawer lid especially on top of the membrane keys.\015\012\015\012Wonder how often it has gone into this blinking red state. ... Fisher and Paykel 24 in. DS603MFC Built-in Dishwasher

Drawers Stuck I've had my dishwasher for a couple of years now. All of the sudden the drawers are extremely difficult to open. I have to use all my strength to pry open the drawers so I can get the dishes out.  It started out as only the bottom drawer having the problem and now both drawers are having it.  It seems to be running fine because the dishes that were in the drawer before it got stuck were cleaned.  And there is nothing blocking the drawer from opening.  It seems like the seal that c


I turned off the electrical breaker for about 8 seconds and it rebooted itself ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Bauknecht GSX 4756w when I switch it on and set the dial to the wash setting, I close the door and it sounds as though it is about to start but after 30 secs just starts beeping. When I open it the cycle setting is always reset to rinse. Can't get it to switch on at all.


My dishwasher will not start: Most common d/w power is 120 volts, check for 120 volts with a ... Bauknecht Dishwashers

I have the dishwasher model number FGHD2433KF, I have noticed in the last few that I have used my dishwasher no matter what setting I push after a few minutes it jumps to 99+.... Example a push quickwash and start it, the time that shows on the screen is 50, it counts down to 49 then it jumps to 99+. Every setting I originally set starts out at the right time that is listed in my book but then after a few minutes it jumps to 99+. Do I need to call service. I purchased the dishwasher in May of


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

Fisher-paykel dd203 started filling with water with drawer open


What you can do is take a baster and empty out the water; then check and see if anything is at the bottom of the machine inside meaning under the thing that twirles and anything that is long put on top rack.Because you can something that is stuck or ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi


... Maytag Dishwashers

Hi, I have a fisher and Paykel double dish drawer model DD605. A couple of days ago when we opened the top drawer all the lights flashed and beeped in sequence repeatedly and would only stop when the power was turned off or the dishdrawer closed. Today I went to turn the top dish drawer on and cannot change the cycle off rinse. I can push the eco button and the rinse cycle works no problem but I cannot change the cycle. The bottom drawer is running as I write this and appears to be fine. An


Hi\015\012\015\012\015\012Could you please let me know which all lights are blinking/lit solid in sequence from right to left. This could be an issue of drawer lock mechanism or flood switch issue. PLease post back with detai ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

When I start the top drawer it defaults to 5 minutes (with the lights Heavy, Fast, Rinse highlighted) runs for a couple minutes, then stops and the LED starts randomly cycling through all kinds of codes very quickly. There is water in the tub that has not drained after completing the couple minutes of operation. This cycle repeats itself if I hit the power button again after the LED starts freaking out. The 5 min cycle shows in the LED, sometimes with the no circulation error, sometimes with the


Here is the solution: \015\012http://applianceguru.com/forum1/24814.html ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a mdd8000aws dishwasher. After a power outage (2 days) the power came back on, and the bottom drawer no longer works. It still make the chiming noise when the drawer is opened, but the control panel is not fully lit up and the washer will not start in any mode. The lights seem to flicker for a short moment and then they all stay very lightly lit up. Is this just a bad control panel or is there some other circuit that needs replaced? BTW, the top drawer works perfectly.


... Maytag MDD8000AWS Builtin Dishwasher

Fisher Paykel singl dish drawer model DS6031..Disconnected elecric, reboot, solid green lte comes on, normal wash setting, drawer locks. After a minute or less the lite turns solid red, cycle jumps to rinse, unit starts beeping, drawer unlocks and the pump continues to run even though there is no water.


... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Hi - I have the Miele G 2470 dishwasher. It starts, and I have it set at "2 in 1 Tab" and on "Normal". I close the door and the machine makes a sound like it is starting, but then after abiut 30 seconds it starts alarm beeping and doesn't run. When you open the door it shows the light is now on next to "Intake/Drain". To stop the beeping I have to press the "off" circle. This sequence happens each time. what do you recommend to get it to work? thank you very much. Lori.


You could check into the User's Guide online manual below:http://safemanuals.com/414159.php?k=41da0c038c6dca28da72cf9056db1c61&ID=63815&q=MIELE%20G2470 ... Miele Dishwashers

The dishwasher seems to be making excessive noise prior to commencing wash cycle.the eco setting is not functioning but the 65 degree wash setting is. sometimes the wash cycle just doesn't start and all of the wash program setting lights flash repeatedly.


... Smeg 24 in. DWD612SS Built-in Dishwasher

I have a bosch dishwasher model number SGS0902GB/05. I use tablets instead of detergent. I put the tablet in the Dispenser and close the lid, noproblem. I then set the programme and shut the door, I usually set the programme to delay start so that it washes dishes in the small hours when all are in bed, however, when I have set the programme and close the door within a minute the dispenser assembly opens and the tablet falls into the dishwasher, I then try and put the tablet back in the dispe


Hello Andrew,\015\012\015\012I'm more than happy to give step-by-step instructions for replacing the detergent dispenser, however it's not cheap (about \302\24350) and it probably doesn't need to be replaced. Some of the smaller component ... Bosch Dishwashers

Dishwasher is not starting. The detergent lid is closed. Door is secure and locked. Tried all three wash settings, i.e. heavy, normal, light. Tried with and w/o heat dry. I also checked the breaker bo


I can't say for sure but it sounds like you lost house power to dishwasher. Being that the breaker is OK remove the dishwasher from cabinet and check power at the dishwasher. Its quite possible that mice may have ate through the wiring ether in the w ... Dishwashers

Both drawers start running when only one was set


When the F1 is triggered it pumps both units out all it knows is the flood switch has been activated it doesn't know where it came from.so both get drained. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Kitchenaid KUDP01FL : Hi, machine will start to fill (on heavy), and then will not engage into the wash cycle. Have to press cancel to drain water. All other settings ( china/rinse/ normal wash) when button is pressed and door closes will "click". No water fills into machine. Have to press cancel to end cycle. Can it be a bad connection being i tryed trial and error and banged on inside of door to maybe "fix" it. NOW, heavy cycle does not fill with water, just a "click" noise. Thanks for


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Good morning, I have a F&P dishdrawer ds605i (i think!) single drawer intergrated front. I dont know whats happened to it. The last cycle it decided not to empty the water out, so i manually emptied it. Now it seems stuck. All it does is run the fan. i can't start a new cycle. The start/pause button allows me to open and close the door as normal and i can hear the lid opening and closing.......... I have tried turning it off for a day at the wall switch. I have also noticed i can


Hi \015\012I guess the model no. you have sent is not correct,however given bellow are links from where you can troubleshoot your problem to your dishwasher which is related to your issue:-\015\012 ... Dishwashers

Pressure washer only starts and runs on full choke. throttle open. The pressure washer turns off when we press the trigger to start washing. Is this because the throttle isnt set high enough?


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

Hi. Our DS603I dishwasher starts on the Rinse cycle on its own - it beeps, red light flashing and no water entering the tub. It does this even if it is open. Similarly, when we try to turn it on to do a normal or heavy cycle, it starts (making quiet a loud noise) and then goes to the Rinse cycle, beeping, red light flashing, no water going into the tub. The pump wheel is turning. We can't find any blockages in the tubes. We have power-cycled it many times. Please help!


Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012\015\012\015\012\015\012 ... Fisher DS603W / DS603B / DS603I Dishwasher

Set dishwasher to start - sounds as if it starts but then 5 mins later beeps. When door is opened nothing has happened and instead of the i.e. P4 programme displayed E1 is displayed? Can you help on what might be wrong?


Possible that there are no outputs from the program controller unit and so you will need to check with a multimeter the voltage to the inlet valve/motor while the washer starts. If there is no supply then the controller is faulty , if no ... Smeg DWI614 Built-in Dishwasher

I have an asko D3450 dishwasher. Washer makes buzzing/humming noise at start of cycle and then randomly through cycle. I checked the sump and pump appears to be clean and impeller spins freely. The cycle seems to work ok. Water is pumping out ok. If you open the door to stop the cycle, the buzzing will continue for a few minutes then stop. If the cycle is restart, the buzzing starts again. The vibrations seem to originate from under the lower spin arm.


If the sound is a bussing - it is the capacitor mounted to the pump. It is failing.Shown here (big white cylinder on right of pic).. ... Asko 24 in. D3450 Dishwasher

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

Cannot start my Comet pressure washer...water runs thru fine. Had set choke to open (push to left) and start to left.


Hi: Some things to check: Is the gas old or contaminated with water. Change it if you are unsure. Are you getting a spark? To check this: BE CAREFUL. Remove the plug. Plug it back into its wire. Hold it WITH INSULATED PLIERS so the tip is close ... Comet Pressure Washers

Hi there, we have had our dishlex 300 dishwasher switched off for a while and today I turned it on. I started a cycle and it stopped after a few minutes and then the Eco button started flashing. I opened the dishwasher to find it full of water and leaking out of the button. Please help! Regards, Pania


Hi just read your posting.Now the reason these dishwashers flash ECO is because there is either water in the bottom tray or your drain pump is open circuit.Is the machine making a pumping noise when it is flashing the ECO light,or is it completely si ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1277 seconds