Having problems with your Fisher and Paykel 24 in. DS-603 Built-in Dishwasher ?

I have a single DS603H dishwasher. When I press start it just beeps a couple of times. Nothing happens, it does not start or anything.


Answers :

This means the machine still thinks the draw is open so ofcoarse will not start, the sensor that detects the draw being shut is on the left hand side of the unit when u pull the draw out u will see 2 little clear squares on the side up the top near the control panel make sure they are clean aswell as the recieving end on the cabinet is clean as they r simple infrared sensors so if the beam of light is obstructed it wont think it is shut as the beam of light comes out of the control board and bounces off a light refracting prism and then sends it back to the board so if the beam cant return it wont start if they are all clean then you r looking at replacing the main control board as the sensor is contained within it
Repair Help & Product Troubleshooting for Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a single DS603H dishwasher. When I press start it just beeps a couple of times. Nothing happens, it does not start or anything.


This means the machine still thinks the draw is open so ofcoarse will not start, the sensor that detects the draw being shut is on the left hand side of the unit when u pull the draw out u will see 2 little clear squares on the side up the top near t ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

I have Whirlpool dishwasher DWH B00. Now it starts as normal filling water for a couple of minutes. Then it suddenly starts beeping and pumps out all the water and just contiunes to beep. This will happen in all programs. We have studied the users manual and cleansed the filters as suggested in the manual, but this doesn't help. There are now problems with the water supply. The dishwasher is not used very much, may be just twenty times. In the start it worked normally, this problem suddenly


Hello & Welcome to FixYa If the sound is coming from the bottom panel then it is the motor that has gone bad and needs replacement. However, if you hear the sound from the control then it can be due t ... Dishwashers

The green clean lights blinks constantly, It will not allow me to cancel and when I try to start a new cycle the start light blinks a couple of times then the clean light starts again, but nothing happens.


... Whirlpool 24 in. GU2548XTP Built-in Dishwasher

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a bosch SHU8815UC dishwasher. It was already installed when i moved into my apartment - so I'm unsure of the age. The dishwasher isn't functioning. When I open the door, the "Clean" light and the PowerScrub button are red. When i close the door, the light go off but nothing happens. One time I closed the door, it started to rev up but would shut off and beep three times after about 1 min. No water comes out. Any ideas? Thanks! June


... Dishwashers

My lg dishwasher LD-14AW2 is not starting. It turns on and displays the time but when I click on anything it double bings and nothing happens. I have cleaned out the filters and my husband has removed the drain hose from the s band and it was all clean. the display looks normal...no error code. Do you have any idea what the problem could be?


Tunr power off 20 min then back on see if this helps ... Dishwashers

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher: Just stopped working before Christmas. I had washed a load a day before, and the next day I couldn't use the Rinse Cycle. The lights turn on for Normal and Heavy, but nothing happens when I press Start. I played with the breakers a couple times, to try to "reset" the machine, but it didn't do any good. I really don't want to be spending a lot of money on that dishwasher, especially after reading all the horror stories abo


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

I have haier dishwasher when you selet a programme the light *** on but nothing happens then the light starts flashing followed by 6 beeps and repeated 4 time what would cause this help kind regards tracey fletcher


This is an error code.... how many times does the light flash?? ... Haier ESD300 / ESD301 Built-in Dishwasher

My mums AEG favorit sensorlogic dishwasher has stopped working. Now when you go to run a cycle it appears to start and then beeps 3 times (as if it has stopped) and nothing happens and the water does not come in.


Please check the timer ... Dishwashers

Hi!, my Ariston L64 dishwasger refuses to start. It seems to reset OK when the dial is turned fully to the left. After the beeps I select a cycle and nothing happens for some time, then eventually the first two lights begin flashing together.That is as far as it goes. Can you help me fix this problem please? Donna


... Dishwashers

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have just moved into a new house with an Asko Dishwasher. It is not working. I program it, the icon for the cycle I have chosen lights up in red, I press start, that lights up in red, the water runs in for about 30 seconds and then nothing more happens. This happens on every wash cycle that I attempt to use. It does not appear to be on time delay as that icon does not light up. Also I have left it for a number of hours after I have tried to start it and still nothing happens. I would appreciat


... Asko Dishwashers

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

It just beeps 3-4 times and nothing happens


... Dishwashers

I wanted to heat up a cup of tea. As I've done many times before, I pressed Time, then 1:20 seconds, then I pressed Auto Start, but fear I may have touched the button below it, which says Start in small red print. The oven wouldn't switch on, and I noticed a small green u-shaped mark had appeared at the base of the 1: I pressed Clear, and repeated my movements, making sure this time that I pressed Auto Start. Again, nothing happened. I've cleared the touchpad several times, but the oven won't


... Danby 22 in. DDW399 Free-standing Dishwasher

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


... KitchenAid KUDC10IXSS Builtin Dishwasher

I turned on the dishwasher tonight and noticed nothing was happening, but I was getting a clicking sound. I moved the dial back to off and started over. Some water went in, but then nothing happened again. I clicked forward one click at a time. Sometimes water came in. THEN WATER STARTED LEAKING OUT. I clicked back to off. After water stopped leaking, I opened the door. There is still water in the bottom. What do I do???


Hi \015\012\015\012Thanks for using FixYa. As the water is not draining and clicking is\015\012coming from the bottom so the issue seems to be with the drain pump solenoid. Usually, these issues are related\015\012to ... Kenmore Dishwashers

I have a Kenmore dishwasher (model 363.14478791). I hadn't used the dishwasher in a month. I turned on the dishwasher tonight and noticed nothing was happening, but I was getting a clicking sound. I moved the dial to the right to off. As I moved the dial to the right, there were lots of clicks and clunks. I started over and turned the dial to the start position. Some water went in, but then nothing happened again. I clicked forward one click at a time. Sometimes water came in. Then water star


... Kenmore Dishwashers

Won start Was using the pressure washer 1st time this year and started on the second pull. Ran out of gas shut-off also noticed it needed oil. Believe, I put too much oil so, I drained some and added gas. At first, there was no resistant in the pull so waited an hour and tried again. This time the resistant was there on the pull but still would not start; no attempt even to turn over. It's been a couple of days...changed the spark plug although, hardware guy said nothing was wrong with it..still


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

I have a KitchenAid KUD1021RWHO dishwasher that will not turn on when I hit the start button. The LED lights work when I press cycle selection ie. "normal" but when I press the start button nothing happens. I have waited for a couple of hours and then it will start. However during the last week it has happened more frequently and now it has not worked for the last (2) days. Any ideas as to what the problem may be? Thank you for your help!!!


Hello,\015\012\015\012This is a very common issue on these units. The touch pad has failed. You can try to flip the breaker off for several minutes and see if that clears the code. More than likely the touch pad will need to be replaced.\015\01 ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Hi - I have the Miele G 2470 dishwasher. It starts, and I have it set at "2 in 1 Tab" and on "Normal". I close the door and the machine makes a sound like it is starting, but then after abiut 30 seconds it starts alarm beeping and doesn't run. When you open the door it shows the light is now on next to "Intake/Drain". To stop the beeping I have to press the "off" circle. This sequence happens each time. what do you recommend to get it to work? thank you very much. Lori.


You could check into the User's Guide online manual below:http://safemanuals.com/414159.php?k=41da0c038c6dca28da72cf9056db1c61&ID=63815&q=MIELE%20G2470 ... Miele Dishwashers

My KitchenAid dishwasher model # kudp01ilbl2 won't start. It is the first time we're trying to start it since we had our water heater replaced (three, maybe four days ago). Not sure how much that may matter. I tried turning off electricity to the dishwasher at the fusebox (overnight), but that did nothing. Normally, you just need to hit the start button and the washing begins. Now, nothing happens. The dishwasher is about six years old.


... KitchenAid Dishwashers

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1463 seconds