Having problems with your Fisher and Paykel DD605HSS 23 in. Built-in Dishwasher ?

I have a dd6051 dishdrawer and both units are blinking red and staying on rinse mode and when I shut the drawers they start running I've reset the breaker they turn green when I put it back on then start doing the same as discribed above-


Answers :

Repair Help & Product Troubleshooting for Fisher and Paykel DD605HSS 23 in. Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a dd6051 dishdrawer and both units are blinking red and staying on rinse mode and when I shut the drawers they start running I've reset the breaker they turn green when I put it back on then start doing the same as discribed above-


... Fisher and Paykel DD605HSS 23 in. Built-in Dishwasher

The dishwasher starts and initially rinses the dishes without heated water. In the next part of the cycle, the water is supposed to heat to a certain temperature.Beginning this morning, in this second part of the cycle,the dishwasher trips the circuit breaker. If you reset the breaker and turn the sihwasher back on, the breaker trips again. What is wrong and how do I fix it?


Hi\015\012\015\012The issue is with the heating element of your dishwasher, it is withdrawing very large amount of power and thus, the circuit gets overloaded and circuit breaker trips. You'll need to check for any short circuits around t ... Dishwashers

We have a KitchenAid KEBC147KSDS06 24" conv. oven. After putting it through a clean cycle, I tried to preheat it to conv, bake @ 350 deg. The display comes up normally and the fan runs, but after 5 sec. the temp disappears from the display and 'Lo' appears in its place. The conv. fan continues to run but neither upper nor lower element heats. Following a suggestion, I tried to reset the oven by turning off its circuit breaker and powering back up, but it did not correct the problem.


It depends how long you had the self-clean function running. The oven is known to overheat and damage the thermostat during self-clean.\015\012\015\012See postings on some user forums.\015\012\015\012 ... KitchenAid 24 in. KUDS02SRSS Stainless Steel Built-in Dishwasher

4 beeps Stopped during wash cycle, not empty, 2 green lights, after trying again does not start and then when turning knob back round to reset it beeps 4 times regularly. Any help much appreciated.


... Indesit 24 in. DI67 Free-standing Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

The controls on my GE GLD4600N10WW have on occasion locked up. In the past, I have resolved this by turning the breaker off and back on. It has now locked up, but won't reset. When the breaker is turned back on, the dishwasher control panel lights indicate "Normal Wash" and "Heated Dry" but the controls do not respond. After several minutes the lights simply go dark. It does not respond to any button pushing.


... Dishwashers

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a DWI 612C Smeg dishwasher I have an error code of the 2 right hand LED's flashing Have tried to reset the programmer (turn off, on then press program 4 times in 2 secs, wait 15 secs and turn off) This enables me to select a programme, but when the programme starts, after five mins it beeps and carries on making the draining pump noise and the programme never starts When I turn it off and back on I get the far 2 red lights flashing again Have looked for signs of blockages and can


... Smeg 24 in. DWI612 Built-in Dishwasher

My Asko D1996 Dishwasher will not start. The control panel has 3 lights staying on - position #1, 6 and 7 and are unresponsive no matter what buttons are pushed - even after turning the power off at the breaker, the outlet and the on/off button.I've tried holding down the start button for several seconds to reset but this did not work. I have also cleared the drain, filters and removed any water and pushed and held the Start button to reset.


... Asko Dishwashers

I tried to turn my washer on and the lights keep blinking and it won't start. I tried flipping the breaker and even left it off for a time. when I turned the breaker back on the high temp wash and the air dry lights were blinking.


... Frigidaire 24 in. GLD2150RCC Built-in Dishwasher

My frigidaire fdb1050rem won't start until I turn of the power for a few seconds then it will wash the dishes but the next time I have to turn of the breaker to reset it before it will start


... Frigidaire FDB1050REM Dishwasher

I have a kenmore 665.15689000 and it won't start. The light on the pots & pans button blinks continuously. I have turned off the breaker and reset the diswasher numerous times. The dishwasher drains after resetting but the pots and pans light starts to blink again.


... Kenmore 24 in. 15689 Built-in Dishwasher

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

I have a GE QuietPower2 (Model GLD5800L00BB) and the lights are blinking and there is a beep about once every 60-90 seconds or so. I have reset the circuit breaker but when I turn it back on, same issue. I can't reset or turn on.


This model has a known problem with the door switches. There are two switches and they both need to work right, otherwise the panel switches will not work right. Turn off power before working on the switches. They both have to open circuit when the d ... General Electric Adora GHDA670N Built-in Dishwasher

My Frigidaire dishwasher will not turn on. The breaker is not tripped, however when I turn the breaker off, then back on, the dishwasher will start just fine. Is there an easy fix without calling a repairman?


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers

My Maytag dishwasher goes for long stretches when it won't turn on even though I push the proper buttons. The buttons won't light either. It turns on by itself after a couple of weeks of sitting idle. Some of the lights may blink on the start panel while the dishwasher doesn't work, but only on occasion will it fully operate. I have turned off the power and turned it back on, hoping to reset the computer part of the dishwasher. It didn't work.


The Control Touch Panels like to fail on may brands - especially Maytag. They are sensitive to humidity - and a lot have the vents out the front - right by the control panel.Please reply using "continue with this expert ... Maytag Dishwashers

Model KUDE70FXPA after use will not start next time unless I go & reset the breaker. Locals have replace breaker. once i turn off at breaker cycle will run.


... KitchenAid KUDE70FXPA EQ Dishwasher

Karcher 3.86M Electric pressure washer. Plugged it into outlet. Unit started running. turned it to off position. Attached hose. Turned on water valve. Turned on switch. Squeezed trigger. Nothing happened. Will not run. Ciruit breaker was reset.


... Karcher PSI Electric Pressure Washer

I need to know how to reset the "brain" the start button is flashing and won't stop when I close the door it makes a humming noise and no water is running. I turned off the breaker but it won't reset. Is there like a "hard reset" I can do


I don't think you may need to reset the dishwasher. All that might be happening is the float switch located in the base may be malfunctioning. It could be stuck. Try pushing it down and see if it lifts up by itself. It should only lift when water is ... GE Adora GHDA656LSS Stainless Steel Built-in Dishwasher

After the wash & dry is complete, the next time I try to use it, won't turn on. I tried cancel and that starts and finishes but can't get any thing else to work. I turned off the circuit breaker but have to wait 6-8 hours before turning back on. Once this is done the machines runs normal again. I have to repeat this process every time I want run. Any suggestions on what might be causing this???


I have the same problem. The only temporary solution I have so far is \015\012to turn off the circuit breaker and wait between 10 & 30 minutes \015\012before resetting the breaker. The the dishwasher will work for one \015\012cycle. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

Kitchenaid dishwasher KUDC10IX does not start, no lights come on. Turning circuit breaker off then on no longer resets it.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1189 seconds