Having problems with your Fisher and Paykel Dishwashers ?

F and P DW681 fills with water then goes into fault mode and pumps out. Start button flashes 7 times. What does this indicate ?


Answers :

Repair Help & Product Troubleshooting for Fisher and Paykel Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

F and P DW681 fills with water then goes into fault mode and pumps out. Start button flashes 7 times. What does this indicate ?


... Fisher and Paykel Dishwashers

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

Whirlpool dwh b10.yesterday had problem with water not going anywhere,had to bail it out.today cleaned all filters,now can hear pump working but doesnt appear to be taking water in.i press start button for two seconds,re-programme,and it does the above.then start button flashes and there is a continual beep the programme indicator changes from a wash to rinse during this process.any help ? thanks pete.


... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

I have whirlpool Dish washer model GU 120 ES (bought in 2001). When we start the dish washer cycle the unit starts for a minute, then the "start indicator" light flashes. As indicated in the instructions, we press the "start button" for five (5) seconds, at this time the washer clears the water out and stops. If you can assist this would be greatly appreciated. Thanks Jeff


I called the service tech.... ... Whirlpool Dishwashers

Tecnik DW2677 Hi, my dishwasher regularly starts to bleep after starting a wash program. When the door is opened it stops bleeping and the right hand light flashes 7 times repeatedly in sequence. By holding down the start and program change buttons together for a few seconds, it will reset. If you then close the door all is well for a few seconds the pump sound like it expells some water and then it starts to bleep again. The above process can happen several times before it decides to do what it


Check your water intake- i had the same issue - a leaky fitting wasn't supplying enough water to the dishwasher. had exactly the same symptoms you describe. fixed the leak, reset the dishwasher & it's working fine.\015\012\015\012\015\012\0 ... Tecnik TDW2677 Built-in Dishwasher

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

We have a DWF A10 and the light indicator flashes 2 times i have cleaned the filters ect presses the start button and held it in but all it dose is drain out and continues to flash can you help me or


... Dishwashers

Haier dishwasher Hi my Haier dishwasher is flashing 3 of the 4 leds and beeping 10 times while the suction pump drains the filter then will not start. Can you tell me what this fault is? water pressure OK ,drain isnt blocked,none of the buttons have any effect. Any info would be helpful thanks.


I useto have same problem. For some reason there was water under machine, then i tilted machine, clean water and problem solved. This is built-in dishwasher that is why water acumulates under machine and "leak cut off switch" turn off machine. You ca ... Haier ESD200 Built-in Dishwasher

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

When it starts i can hear water inter washer, but it does not pump water into the spin jets after a few minutes it makes a peebing sound and the washer, dry, clean buttons starts flashing and it dose


... Samsung DMT300RFS Builtin Dishwasher

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace. ... Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Hi, I have a fisher and Paykel Nemo dishwasher. It takes water in with no problem. But it stops after fill up the water and the led near "start" button keeps flashing. (flash 6 times and stop for a second, then flash another 6 times, so on) By the way, Heat element has been confirmed works. Any comments? Many thanks.


... Fisher and Paykel Dishwashers

Miele Optima G 2430 - The dishwasher will pump water in for 5 seconds with the Intake/Drain light flashing 5 times. Then the light stays on for 5 seconds and it does nothing. This process is repeated for about 10 minutes untill the washer is filled to the just below the door with water. Then the washer starts running for about 1 1/2 minutes and drains the water. Then it all starts over. If I let it do this for a hour - The display reads F12 with the Intake/Drain light flashing.


Hi\015\012\015\012The first thing that should be checked is if its draining\015\012properly as it could be that the drain hose is clogged and needs to be cleaned.\015\012The drain pump also should not be clogged. ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Whirlpool ADG 7560/2 has been pumping out then stopping, programme not starting & flashing cancel button. Is now permanently stuck with cancel light flashing 8 times


... Kenmore Dishwashers

Hi. Our DS603I dishwasher starts on the Rinse cycle on its own - it beeps, red light flashing and no water entering the tub. It does this even if it is open. Similarly, when we try to turn it on to do a normal or heavy cycle, it starts (making quiet a loud noise) and then goes to the Rinse cycle, beeping, red light flashing, no water going into the tub. The pump wheel is turning. We can't find any blockages in the tubes. We have power-cycled it many times. Please help!


Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012\015\012\015\012\015\012 ... Fisher DS603W / DS603B / DS603I Dishwasher

Whirlpool APD5550 Dishwasher, cycle does not start, green light on start button flashes 6 times, pauses, flashes 6 times etc. can you please give me some indication what the problem may be. Thanks


... Dishwashers

On my whirlpool ADP962 dishwasher the start light is flashing but nothing is working. I can change the programme type (ie rinse, wash etc) but the programme will not start. I can't select either half load or a time delay. By holding the start button it will start the pump but when this stops it goes back to a flashing start light. The programme progress lights are not lit. What is this telling me and how can I reset it?


... Whirlpool Dishwashers

I have an ADG7550 whirlpool dishwasher. Am experiencing a fault when placing on a normal 65 degree programme it starts to fill and then defaults to pre-rinse and the start button and light flash eleven times. Can you explain what type of fault this could be ? I have had a similar problem 12 months ago when it was described as a water pressure problem which again was in the winter and wonder if this is the same. I would add that if I re-set the start button by holding it down and then re-start


... Whirlpool Dishwashers

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

I have a Miele G892 SC dishwasher. When I start the cycle, it drains (except for a bit of water left below the triple filter). After that, the intake valve opens and water enters. It then does nothing for a period of time until the "intake/drain" indicator light starts flashing. When I open the unit, I find about 1/2in of water in the tub (above the tripe filter). I have 1. cleaned the intake valve filter (no blockage found) 2. Inspected the drain line at the base of the unit as well as t


The pump is running due to the float switch or the float itself either being stuck open or broken and showing a fault this is why you have water going in to a certain point but not the point required for washing the dishes and then due to the float s ... Miele Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2058 seconds