Having problems with your Fisher and Paykel Dishwashers ?

The electronics on my Fisher Paykel "dishdrawer" seems to be frozen. "00" is visible---which normally means the cycle is over. I'd like to do another load, but can't get anything. Thanks


Answers :

It might help to know what is the model of your dishwasher.
\015\012
\015\012Have you tried turning the mains power to dishwasher off and back on. If there is a child lock button then press it for 3-4 secs to make sure it is unlocked.
Repair Help & Product Troubleshooting for Fisher and Paykel Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The electronics on my Fisher Paykel "dishdrawer" seems to be frozen. "00" is visible---which normally means the cycle is over. I'd like to do another load, but can't get anything. Thanks


It might help to know what is the model of your dishwasher.\015\012\015\012Have you tried turning the mains power to dishwasher off and back on. If there is a child lock button then press it for 3-4 secs to make sure it is unlocked. ... Fisher and Paykel Dishwashers

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I recently bought a different type of dishwashing detergent for my Frigidare dishwasher and my dishes look as if they have not been rinsed. They cycled all the way through the drying cycle so the detergent dried on and was difficult to remove. I would like some advice on whether this sounds like a detergent problem or mechanical problem before I try another load. This washer is not new. It was in the house I bought and I've only been using it for about 2 months. (I usually use Casade Liquid and


The best way to use your dishwasher is the way it was designed.\015\012if your unit has a compartment for jet dry or rinse agent then you should add and fill that compartment with rinse aid. try not to buy soap with any extra like soap with jet ... Dishwashers

Our KitchenAid Superba model KUDS01DJss0 ( about 7 years old and has always worked fine) I think is not heating . . the dishes come out wet and don't seem very clean if they had especially if they have a small a bit of something like peanut butter on them when loaded ( so lately I've been dong a pre-wash by hand). Unit doesn't seem to get very "hot" during the wash/dry and steam does not billow out when I open the door soon after the cycle completes like it used to. It does feel warm to the


Hello. The new heating element will come with a new control board. There are no tricks to the change actually, the easiest way to change the heating element is to unhook the plumbing, electrical, and drain hose then pull it out and get to the back ... Dishwashers

KitchenAid dishwasher: KUDS01FL - I have had to replace the fuse every year and now I can't even get through on cycle with the fuse going. It is now dead again! It almost makes it through the full cycle and then stops (fuse blows)- no power - and there is some water left in the bottom which I have to physically remove. I spent a fortune on repairs every year since I bought it and would like to try to avoid another charge. I appreciate any help that you can offer. Thank you, Carol


I would check the pump. It may be slightly jammed or have debris which is causing it not to fully move or cause it to move very hard popping the breaker. Also with a jammed or broken pump, that can also cause water to be left in the bottom of the mac ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Dishwasher is not cleaning well, dirty film all over everything, like its not rinsing. In rinse cycle only, some water comes out of lower left port inside but nothing else. Hear a low buzz underneath unit like a motor or pump is energized but no water getting to the top.During normal wash cycle, buzz from underneath seems to cycle on and off, say every minute or so like its cycling on an overload. Do I have a bad pump and if so how do I get to it?


Hi. This may well be a pump issue, or an obstructed hose assembly, as well. Your symptoms are indicating that the impeller may be damaged. In order to pull the necessary schematics, I will need the entire model number. This ID tag will allow me to pu ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

My Fisher Paykel dw60cdw2 dishwasher stopped working mid cycle and I cant get it started again even aftre switching power off and pressing reset.. All lights on the console are working except the number display on the left side. What is the problem likely to be


Had the same problem and it was the microswitch that is behind the door skin which is associated with the lock mechanism. got a new one and away she went ... Fisher and Paykel Dishwashers

Hi, Had a power cut at my home and my Caple Di455DL Dishwasher was mid cycle on a glasswash program at the time, since power has been regained it will not restart or reset itself, it just lets a pulse of four beeps go once the door is shut and makes a sounds like its trying to pump out water? tried turning off at mains etc but cant get it to reset!


... Dishwashers

A knife with a plastic end must have fallen down during a cycle and melted to the heating coils of the dishwasher. Could not get it to come off at all! Then unfortunately we forgot and did another load. Obviously it has melted further and still wont come off. I'm not sure what to do? Thank you!


WEll, it will take heat to get this plastic off. nothing else works.I would use a heat shield, gas torch and a wet terry cloth towel. heat the unit up and pull off with the damp towel. Really nothing else works. Sometimes you can activate the burner ... Dishwashers

Model #kudi01flbl6 flashes a 7 blink code on the clean l.e.d. won't reset via common procedures,turning on and off power. I have taken the interior apart and cleaned out many peices off glass, tooth pick and rubber bumpers off cutting boards. Would really like to know what that 7 blinks means. I can't get it to even start a cycle.


... KitchenAid Dishwashers

We live in an apartment and our hot point dishwashers timing is all off and i thought if i could fix it myself, i'd love to do that instead of calling our manager, i will call him, but if its an easy fix i'd like to try it out.. it will just stop in mid cycle, and you have to manually more it a fraction of an inch to get it restarted, then at the end it doesnt fully drain, and the drying takes forever, so if i cant fix it, i'll ask for a new one..


It might need a new mechanical timer (sounds like the timer is sticking) installed and the parts will cost money... so you might want to go the route of the manager. The dial that you turn to set the dishwasher is part of the mechanical timer. Someti ... Dishwashers

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

My dishwasher quit running in the middle of it cycle like there is no power going to it..... there is water standing in the bottom of it and i cant get the washer to come on or anything.... could it be something simple????


It is simple to repair. you need a thermal fuse. take the control panel off and right where the control board is you will see the thermal fuse. you can either replace it or just splice the wires. let me know if you need further help ... Kenmore 18 in. 14432 / 14439 Built-in Dishwasher

After 3 years it just started making a loud noise, I am no expert but it sounds like a fan in a motor. I have only heard it today, but I am betting it will still happen next load too. I didn't change any of the settings, have been running the same way forever. When I did hear this noise I started pushing buttons to see if I could get it to stop, no good, no change. The cycle has completed and everything looks ok, waiting on the dishes to dry. Drainage has never been a problem for me either.


I would say this is a build up of lime.try changing your tablets and checking your salt levels.there is no fan .try what i say and see what happens.have you found a glass broken it could be as simple as that but i dont think its serious.adrian,,,, ... GE Nautilus 24" Built-in Dishwasher

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

I have an SDMO generating set with a Mitsubishi S3 L2SD engine it is supposed to run at 1500 rpm but goes up and down depending on load, if I set the rpm at no load to 1500 as soon as a load is applied the revs drop and so do the cycles from 50 to perhaps 48, if I set the revs on load, then off load the revs go up and the cycles hit 53 plus which means for example my washing machine does not want to know, I suspect the govenor on the pump but do not want to change the pump if this is within para


Set the no load revs such that you get 51 Hz out of the generator, at 80% load this ought to give you something like 48.5 Hz with less than a 3% drop in output voltage. If not, you might have governor problems but I'd try servicing and adjusting it b ... Karcher 2500 PSI Pressure Washer

The dishwasher stops at the rinse cycle, does not drain and then the Quick Rinse button is the only cycle that will light up. Sometimes I can get the washer to choose a different cycle... but it is about every third day. And once the load gets to the rinse cycle, it starts all over again.


... Kenmore 13593 Stainless Steel Built-in Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

My kitchenaid dishwasher won't wash. The clean light blinks and if I can get it to cycle, it turns on to ''2 minutes'', during which 2 minutes it makes some washer-like sounds but doesn't clean, dry or spit out any water. Before this, I wash having trouble getting my dishes clean. I wash able to get the bottom rack clean using the heavy duty cycle, but the top rack still didn't clean


... KitchenAid Dishwashers

Whirlpool dishwasher DU1015XTXBO Stopped working during cycle, acts like don't getting any power. Checked the plugin and it works. No lights or anything coming on the dishwasher. Its like it just


... Whirlpool Dishwashers

Eurotech Model EDW254EWXX runs a 13 minutes cycle before washing like usual, but now it is getting stuck and not doing anything during that 13 minute cycle. No water is running, and it makes NO noise at all. We are not getting any errors displayed. I have unplugged it, and shut off the circuit breaker for 20 minutes, but the problem is still there.


... EuroTech 23 in. EDW254E Built-in Dishwasher

The dishwasher does not complete a cycle. It starts the cycle just fine but then it stops after one minute. It seems like it gets stuck and won't move to the next step. I do hear a slight clicking noise similar to a clock ticking, like its trying to move on, but then it stops. It clicks three times. When I open the door the "fine china" light is on even though I set it on "normal". Is there a "re-set" button?


The Control Board is gone, the part is $475.00 Find a new one.... ... Viking Designer Series DFUD041 (Premium) Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Dishwasher problems I have a counter top dishwasher and it's not cleaning things like it used to i think its clogged but i cant get to the drain because it is in the bottom i tried draino but it didn't work i also tried unscewing the bottom but i cant get that part out i think there is somthing stuck in there.


First thing to check water hose that connect at back of machine. pull the screen out and clean it. use a pliers. I run my under water then use a q-tip if its clog to clean the rest.\015\012\015\012Then pour a cup of vingar in machine and ... Danby 22 in. DDW396 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1651 seconds