Having problems with your Fisher and Paykel Dishwashers ?

I have the two drawer dishwasher. It's about 10 years old. The top drawer continues to work OK but for the last three attempts when I run the bottom drawer water gets out into the drip pan below and gives the F1 signal. I can dry the drip pan out and clear the F1 signal so the top drawer works. But running the bottom drawer causes water to leak again with the resultant F1 signal. There is very little water in the bottom drawer (just a little in the filter bowl) so I think the pump is pumping


Answers :

Hi,

Unless you keep using the wrong detergent or keep putting dishes that \015\012are to tall in there. i would have to say your actuators ar bad and its \015\012not letting the lid go down to seal it all the time.There is no adjustment. You need to replace the lid actuators.\015\012
Remove the drawer by press int he tabs on the side. The tabs are about 2\015\012 inches behind the front panel and are al the bottom of the drawer on \015\012the sides. Once you remove the drawer you will see the white actuators \015\012on the inside of the dishwasher. \015\012 \015\012

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!
Repair Help & Product Troubleshooting for Fisher and Paykel Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the two drawer dishwasher. It's about 10 years old. The top drawer continues to work OK but for the last three attempts when I run the bottom drawer water gets out into the drip pan below and gives the F1 signal. I can dry the drip pan out and clear the F1 signal so the top drawer works. But running the bottom drawer causes water to leak again with the resultant F1 signal. There is very little water in the bottom drawer (just a little in the filter bowl) so I think the pump is pumping


Hi,Unless you keep using the wrong detergent or keep putting dishes that \015\012are to tall in there. i would have to say your actuators ar bad and its \015\012not letting the lid go down to seal it all the time.There is no adjustment. Y ... Fisher and Paykel Dishwashers

We have a Fisher& Paykel dishwasher with 2 drawers -- one on top of the other. Model DD603. The bottom drawer works fine. But the top drawer is not working properly -- it repeatedly stops in the middle of the cycle and there is water left in the drawer. Previously when this happened, we called a repairman; he removed the top drawer from the machine, said it was "off track", flipped some lever, and put the drawer back. He seemed a little embarrassed by having to charge for a service call for


Are you able to provide a bit more information on what you see when the dishwasher stops in the middle of the cycle -\015\0121 - is it displaying the time remaining in the cycle and is it always the same time?\015\0122- do you get any fau ... Dishwashers

Have Fisher-Paykel DD603 double-drawer dishwasher. Top drawer motor making loud noise. )Bottom drawer fine.) Still seems to wash and definitely pumps water but sounds like a "motor with a broken belt." Checked filter and rotating spray arm - no problems. (Found a little broken glass in filter; could be very old.) Suggestions?


If glass has gotten past the screen and into the pump, you may have a pcs. logged in the pump housing.\015\012Best way to correct this, is to remove the pump inlet and outlet lines and flush out with a water hose.\015\012Keep ... Dishwashers

The dishwasher top drawer is leaking all over the floor during the cycle. When the top drawer is running, It fills up the the bottom of bottom drawer with water also and then neither drawer drains completely. The water is a light brown color after a wash and often half the soap is left in the dispenser.


Fisher and Paykel design a air gap kit to prevent the water back flowing to the other while one is running. it really works and worth of your money.\015\012You need to change the lid seal and a pair of actuators from the top drawer. Because of the ... Fisher and Paykel DD605SS Stainless Steel Dishwasher

I have the two drawer model dish-drawer system. In the past the top seal leaked and since has been replaced with a new seal. Worked well for several years after but then the top drawer quit running. So we started to use the bottom drawer. That was fine for awhile althought it would pump waste water into the top drawer. Now neither drawer will work. The bottom drawer starts up and shuts down. I pulled the lower drawer and it is dry.


If your model has got an LCD display are you able to record what shows up on the display when the bottom drawer shuts down. If no display then are you able to note down the LEDs which are on inside the top of the drawer lid. It is likely there is no ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

We just purchased a used Fisher and Paykel DS 603-i. After installing and running the normal cycle there was a lot of water left on the bottom of each drawer. We ran the bottom drawer (water stil siiting on the bottom of the top drawer) and part way through the main wash cycle we got what I think was a F1 error code (we do not have the LCD version but the Rinse light was activated). I took out the bottom drawer, dried out the basin and then took out the washer and reattached the drainage pipes t


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You’ll need to reset it by poweri ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

I have a kitchenaid Model KUDW03CTBL2 dishwasher. It is pumping water, but the top sprayer and the one under the top rack just have a little water coming out. Not enough to make them spin. We also noticed the water in the bottom when opened is not as much and it is cool not hot. The dishes on the top rack will not clean, and the bottom is not completely clean. We have checked water pressure and water tempurature through the house, All is operating fine. This dishwasher is only 1 year and 10month


... KitchenAid Dishwashers

The bottom drawer is filling with excess water after the top drawer cycles. It doesn't hamper the use of the bottom drawer as the excess water drains during the cycle, but I am concerned about rust, etc. from the excess water standing in the drawer. Please advise. Denise Arnold


Hi\015\012 \015\012This means that you have an overflow leak problem. You need to shut off circuit breaker or pull fuse. Next let it dry out for up to 4 days ,peak under dryer and feel metal drip pan and ... Fisher and Paykel Dishwashers

Fisher paykel Hi I have a fisher paykel dd603 dishwasher. when I run the bottom drawer on its own ,,it also fill the top drawer with water ! so after the dishwashing cycle , im left with water in the top drawer. im guessing that a valve should close on the top drawer to stop this happening? is there a part I could order and replace myself? thanks [email protected]


Check your email ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

I have a Kenmore Ultra Dishwasher. The bottom arm spins, the top doesn't, although water drips out. The water fills up under the heating element. The top dishes aren't getting clean and the bottom aren't as clean as they used to be. I also noticed that the soap dispenser is open, some of the soap is gone, but there's still some soap in left in the dispenser. This never happened before and it happens all the time now. Thanks for any help you can give me!


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Dishwashers

The top drawer on our dishdrawers makes a clicking kind of noise for about the first 2 - 5 mins of being on. Then goes fine with the occassional clicking noise during the cycle. It is slightly noisier than the bottom drawer. When the cycle is finished there is a couple of inches of water left in the bottom, so the dishes don't dry properly. The bottom drawer works really well with no problems at all. What do you suggest?


... Fisher and Paykel DS605I Built-in Dishwasher

Fisher & Paykel 2 drawer dishwasher: I too cannot get power to top drawer. 4 days ago we had an F1 code. My husband pulled out drawer, wiped up water, and dried it out. Put it back in overnight, and both drawers worked fine. Now the bottom drawer is okay, but no power to top. Help!


He might have unplugged something in the proccess of drying the bottom ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have an older Bosch dishwasher I just hooked up in my condo. WHen a cycle is done there is no water is located at the bottom of the inside of the dishwasher, yet 2 days later water will drip on the floor (with the dishwasher door closed) and I'll open the dishwasher door and therewill be 2" of water at the bottom. The flexible water discharge hole located in the sink base is located at the top of the base cabinet, and the hose runs completly 100% downward from that hole to the garbage disposa


When you empty you sink, some of the water is going down the drain hose of the dishwasher. take the drain hose up as far as possible in a swan neck ... Dishwashers

Top drawer of dishwaser has standing water when bottom runs


... KitchenAid KUDH03DT Dishwasher

Top drawer works but bottom drawer shows code u3 and bottom drawer started leaking water before the u3 code showed up


U3 code generally relates to drain pump blocked. This could mean the water is not able to drain out. Leaking of water is not a good sign. Shows the vacuum seal is not working.\015\012\015\012Clean the drawer door from inside and make sure ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

On our double drawer dishwasher, we are getting a code--which illustrates no water--this is for the top drawer, the bottom drawer, works fine--and the water supply is on--please help.


Sorry to read about your problem, I hope this helps you out.you must have a defective water inlet valve, for the 2nd drawer. or a bad control relay for the valve.I tried to help you. Please help me and Rate/Vote on my response ... Fisher Dishwashers

I have model KUDV24seal5. It leaves a film on the glasses, and they don't look clean. The water in the bottom after running it is also cloudy. I run the rinse cycle before loading and put vinegar in the water that helps a little. I've cleaned the bottom and the arm and the pipe the water goes up to the top level. Is my pump going out?


... KitchenAid 34 in. KUDV24SE Built-in Dishwasher

Middle and top spinners do not spin The pump is pushing water up the back delivery tube. There are no dishes in the unit and I was able to trick the door into thinking it was closed so I could watch what was happening. Or Not Happening The spinners are completely free of calcium or soap build up and both top and middle are easily spun with a finger. While the pump and bottom spinner were working, I pulled the top drawer out partially and there appeared to be a good flow of water coming out of


Hi,\015\012 Remove each spray arm and check it is clear of food particlesat the jets. The next problem may occour at the rotating joint . If the seal is not good, you can loose a lot of water out of this point.. If both of these seem reasonable ... Dishwashers

The top drawer of my fisher paykel dishwasher stops during the cycle and shows an icon of a tap with a line threw it (assume that means no or low water pressure). the bottom works fine so I assume water pressure is not the issue; is there a sensor that could be bad? Also, I did switch the controllers between drawers (good instructions on the fisherpaykelparts.net website) but the problem stayed with the drawer, ruling out the controller.


Did it fill with water? could be 1 of your water valves is faulty, or the little filter for the inlet water is blocked. please reply 4 more help. i"m sure i can fix this problem for you. good luck. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

KUDD03DTSS Double Drawer Dishwasher. After washing dishes, water is in the shield on the bottom of the drawer. Are there any know problems with leaking out the bottom? Could it be leaking out the seal at the top and ending up in the bottom?


... KitchenAid KUDD01DSSS Built-in Dishwasher

The top dishwasher is flashing F1 and the motor won't turn off. It will drain if I pour a cup of water in it. The bottom dishwasher is working just fine. There is no water in the bottom pan. I usually find a few drops of water when it's flashing F1. Thank you!


Hi.the troubleshooting, and the error code depends on the make of the dishwasher.If the dishwasher does not stop draining, then the float sensor switch, or the pressure switch in the drain system is faulty.Details ... Dishwashers

I bought a used 7 1/2 year old fisher paykel dd603 for my tenant, it worked fine the first time. second time she got F1 code on both drawers. water was in lower pan, we sopped it up and dried it out. also drawer was not seating level but was lower on left side, and insulation had fallen off left wall. all now corrected. but now the top drawer leaks onto floor on left side. it did not leak before repairman came out, we checked thoroughly. repairman says top lid not seating properly and i need ne


I have the same model F&P and just experienced similar problems. My top drawer was leaking due to that "not important" thin white tube. It really sounds like you called a general appliance guy and not a trained F&P repairman. The guy who fixe ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

The top drawer started getting very loud - maybe the water pump? Now it looks as if no water is getting into the drawer so dishes remain dirty. The bottom works fine, and is not loud when running.


Yes it is likely the pump rotor is seized. I am assuming the water goes in to the drawer but does not get moved around by the washer arm. This i ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Bottom unit does not always seal and causes water to collect in bottom pan which throw unit into f1 status. Sometimes it stays sealed and is difficult to pull drawer out. Is there a way to reset the unit properly? I know how to pull the drawer and fix the f1 problem but it seem like the seal issue is becoming more frequent. Thanks


These dishwashers are very sensitive to grime collecting around the drawer edges. Try cleaning with a damp cloth by rubbing along the top edges and the sides where the drawer door sits flush with the body.\015\012\015\012Also trun off pow ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1621 seconds