Having problems with your Fisher and Paykel Dishwashers ?

Hi, I've got DS 603 single draw dishwasher Ser. No. CPM 739878, It has given a fl code for the flood switch. I have removed the draw and made the observation that the lower steel housing has partially flooded, hence the code. I intend to replace the flexible hoses Input and discharge hose. I am wondering once I replace the hoses, dry the housing and associated printed circuit bourd area should the fault code reset its self or is there further tech. assist required. The draw was manafactured


Answers :

In the catch basis there is a printed circuit board that contains a sensor that detects moisture. Once throughly dry however, the sensor will no longer sense moisture and the flood code will cease and desist.
BUT before replacing the hoses, (alot of work) please, please consider these points....
There are three possible scenarios for a flood code;
1. Defective lid motor(s)...Each drawer has two lid motors (one on each side of the drawer) that pull the lid tight to the drawer when the cycle is started. Lid motor issues were very common on early models
2. Something too tall was placed in the drawer preventing the lid from closing completely.
OR
3. (only seen this once) the drain hose developed a crack causing water to leak only when draining.

Hope this helps.....

Let me know if I can be of any further assistance

Regards

reg501

The FixYa Team.. 'There for you'
Repair Help & Product Troubleshooting for Fisher and Paykel Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, I've got DS 603 single draw dishwasher Ser. No. CPM 739878, It has given a fl code for the flood switch. I have removed the draw and made the observation that the lower steel housing has partially flooded, hence the code. I intend to replace the flexible hoses Input and discharge hose. I am wondering once I replace the hoses, dry the housing and associated printed circuit bourd area should the fault code reset its self or is there further tech. assist required. The draw was manafactured


In the catch basis there is a printed circuit board that contains a sensor that detects moisture. Once throughly dry however, the sensor will no longer sense moisture and the flood code will cease and desist.BUT before replacing the hoses, (alo ... Fisher and Paykel Dishwashers

9e error code on Samsung dishwasher. dmr77lhs. Already replaced drain hose, worked for 3 months, then 9e came back. Replaced supply hose but did not change error status.


I get this error code every 9 months or so with my DMR78.... Every time, I pull the dishwasher out, remove the cover, and then clean out the float on the left side of the dishwasher (the white plastic piece in the bottom center in the attached ... Dishwashers

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

We're trying to install our dishwasher and there is a 3rd hose attached on the side. It appears to be a drain of some kind, part number, we think, printed on it is FRU 10967 19/07/04 08:33 Can you tell us what it is and where and how to attach. The one it's replacing only had the water hose and the drain hose, no third hose. Thanks


I just installed my Bosch dishwasher a few days ago and wondered about the same thing. The instructions for hooking up water supply and drain lines did not mention this third hose at all. \012\012However, 'the third hose' (which appears open on ... Bosch 24 in. SHU43 Built-in Dishwasher

Electrolux 1113312-20 Hi - my dishwasher circuit board has burnt out (melted) and i need to replace this section. The details on the unit state:- Computime CODE: ELE4157 Electrolux CODE: 1113312-20 Hardware CODE: 156050732 SW: DMA24_MR 230V/roHz T65 Date: 09-281 Can anyone help to advise the best place to get one


... Electrolux Dishwashers

Got a siemens se26293/gb/13. The water inlet hose has been chopped off during house move by incompetant idiot. This also had a cable next to it. We now don't possess an inlet hose, only small piece of blue hose and black cable going inside machine. Can it be replaced and if so where from.


I have this problem too - our hose has split about 20cm from where it goes into machine and can't get a replacement - what did you do? ... Dishwashers

Drain hose leaks. can i buy a replacement house


You can use generic hose. \012\012Turn the breaker off.\012\012Remove your unit. It may have screws holding it to the underside of the counter. You may also need to lower the front legs by turning the feet with a wrench.\012\012Look ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Water stays in the top draw filter area, have checked hoses found good connection and no kinks in the lines , could this be a pump motor problem. I have had a problem the first month with this unit and the tech. replaced a lot of parts including the computer for the top draw . i am now out of warr. time not by much and am starting to get upset that this problem is happening after such a short time.


... Fisher and Paykel DS605I Built-in Dishwasher

LG LDF6810ST had OE error. Disassembled found no obstructions blew air through and vacuumed hoses to air gap and to disposer, no obstructions. Never heard pump run when starting cycle, so replaced drain pump. Still doesn't run. Looked at the service manual, and the only other suggestion is repair circuit? Is this the circuit on the bottom right of unit or the pcb up top? Wires and connections all look fine. What else could it be. Any suggestions appreciated!


Hi,Usually my First Response to this Common Error is :-Most likely pump trap is clogged up. Access it behind small door at front. Drain water out through small hose that is there otherwise water will be all over the floor when ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

The "clean" light blinks 8 times, then there is a pause, then it blinks once. The dishes are clean but not dry, as if it has not completed the drying cycle. We had an engineer out to fix it who said it was the circuit board and that the blinking light code indicated "too much suds", he replaced the circuit board, but it didn't make any difference. It's an intermittent problem: sometimes the machine completes its cycle OK. I ran it with just vinegar and nothing else in (no detergent, no dishe


... Kenmore Dishwashers

Samsung dmt800 dishwasher error code 4e. Water valve is open, pressure and temp correct, flex water hose not kinked, water inlet valve is free of debris. next steps? replace water inlet valve?


... Samsung DMT800RHW Built In Dishwashers

My dishlex dishwasher is a model 560 silent range with eco save and has a printed circuit type switch arrangement it has man code of b8833ww or 88833ww the problem is that the pause start button activates but dose not latch in I suspect that the problem is with a latching relay behind the switch panel as i have had the front off and cleaned the contcts with contact cleaner! all of the buttons work including pause ! any advise would help as would a wiring diagram and or a operation or workshop ma


Hi.The switch on this machine's control module is electronic. I do not think you will find a relay. In normal conditions the button is not supposed to stay latched If the button is defective you may get the same problem when ... Dishwashers

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

My dishlex dishwasher is a model 560 silent range with eco save and has a printed circuit type switch arrangement it has man code of b8833ww or 88833ww the problem is that the pause start button activates but dose not latch in I suspect that the problem is with a latching relay behind the switch panel as i have had the front off and cleaned the contcts with contact cleaner! all of the buttons work including pause ! any advise would help as would a wiring diagram and or a operation or wor


Latching relay or door lock assembly need for you to check on that model number 560 silent range wont come out on dishlex's site should be a dx followed by some numbers try also to shut off the main power for 7 minutes to the unit to reset the contro ... Dishwashers

Gaggenau GM 915-710 UC6 dishwasher will not fill and wash. Close the door, turn lever. Empties water from sump. (drain hose was not clamped above disposal outlet nipple, fixed that) Machine empties sump, but will not stop after sump is dry. Will not initiate fill and wash. Manually stop machine. Can't get control board to do the diagnostic to get an F #. Pressing button 1 and 3 at the same time. A couple of the plastic tabs on the circuit boards plastic support housing that link the


... Gaggenau GI936-760 Dishwasher

I had an IE code displayed on LD1415M LG dishwasher and replaced inlet hose (with builk in aqua stop valve). Afetr reassembly, dishwasher now tries to fill as soon as power switch on door is turned on, before program is selected.


Test the timer: can be bad adjust it. see the diagram for you check again any wires in wrong place, any devices with bad adjustment. ... Dishwashers

I just finished a service call for my 5312UC/UC12. The tecnician says he saw water leaking under neath the machine but hoses were secure and no visible crack to the motor housing, The machines pump works but very little water is actually put into the tub, hence no dishwashing. This technician says that this is a repair that most technicians avoid because it takes a long time and costs alot and violated some sort of warranty. He recommend replacement after only 7 years!


This leekage may come from thermostads water isolation ring, just under rezistance leads. There must be a ceramic holder to fix it to rezistance. İf it is broken, thermostad may go down, or rezistance leads isolation (lastic washer) may leak wat ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Kenmore 665.13823 dishwasher couldn't stop a washing cycle. It was identified as "control board" issue. Is it possible to fix the circuit board/timer insted of replacing the board? Also, where are the mayjor screws located to open the housing for the control board? Thanks


Hi,Unfortunately there is no way to repair circuit board or timer. The procedure to replace control panel is :-Step 1 Disconnect the power supply to the dishwasher by turning off the circuit breaker. The circuit br ... Dishwashers

Top Rack does not clean, Pump was just replaced. No Error codes. Heat is good, house water pressure is good, drain is good. I've cleaned the filter.


You do not say if the drain pump, the main motor, or the entire motor / sump assembly was replaced. If all the holes in the upper spray arms are clear, replace the VIRO motor. It is a small motor next to the main motor, and it switches a water valv ... LG Dishwashers

Asko 1555 Dishwasher will not drain. Bottom of kick panel pan will fill with water triping the float switch?, leaving an error code. Is it safe to assume that the out pump needs replacing. I had the kick panel off and smacked the motor housing a few times and it ran for a few loads, but is now again stopped working.


It might be the pump, or it might be an obstruction elsewhere. If you have an air gap on your sink/counter top, open it and check for debris. If it is clear, unscrew the main filter basket. There is a black plug on the left side of the bottom well ... Dishwashers

Hello, Firstly, thank you for what you do, you help so many people and I know it takes time. I have a Bosch SHE44C06-UC Dishwasher. I fixed the E1 (Heating Circuit) error. First, before I found the writeup about the solder joint, I bougut a new heater and replaced it, ithe part included the element, flow switch and high temp sesor soall are new, then I fixed the solder and E1 went away and the cycle finsihes and the dishes are clean and dry. Still I check the error codes and still have


... Dishwashers

Getting error code 1E I've replaced the sump pump, cleaned the screen at the water inlet, checked water flow from the hose. Continue to get the 1E once water has entered dishwasher and begins the wash cycle.


... LG 24 in. LDS 5811 Built-in Dishwasher

I have a dishlex global 500, will not draw water in, comes up with error code nf. I have taken all hoses and filters apart, cleaned them, still no luck. I cannot find a blockage. ps, the dishwasher tripped my power off , then error message came up when I reset power


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0803 seconds