Having problems with your Fisher and Paykel Dishwashers ?

Anyone have experience with a Fisher Paykel double draw dishwasher (model DD24) getting stuck in wash mode? Once it hits exactly 48 minutes it stays there. Only several hours later it cycles through OR you have to turn it off put it in rinse mode to complete. Already tried all the basics (unplugging, no fault codes, cycled through the diagnostics everything good and working). Did the quick diagnostic cycle of 14 minutes and everything cycled through fine. Next step will be to put the bottom cont


Answers :

Repair Help & Product Troubleshooting for Fisher and Paykel Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Anyone have experience with a Fisher Paykel double draw dishwasher (model DD24) getting stuck in wash mode? Once it hits exactly 48 minutes it stays there. Only several hours later it cycles through OR you have to turn it off put it in rinse mode to complete. Already tried all the basics (unplugging, no fault codes, cycled through the diagnostics everything good and working). Did the quick diagnostic cycle of 14 minutes and everything cycled through fine. Next step will be to put the bottom cont


... Fisher and Paykel Dishwashers

ASKO 1595 Dear greendude, thank you for your reply! i haven't checked the solution yet but wanted to specify: i've got ASKO 1595 and have had it for 4 years. recent year it started to mulfunction: sometimes it would stop in the middle of draining cycle and fault light would flash. this could be normally fixed by unpluging power cord, waitng for a few minutes and pluging power back again. wahat happened now is the different: dishwasher came on on its own, nowbody started it. it came on (draining


Yes have you tried what i suggested yet ... Asko D1776 Stainless Steel Built-in Dishwasher

My Dacor dishwasher will only do the 10 minute rinse cycle. No matter which button I push, it only does the 10 minutes rinse cycle. We have tried clearing it, we have unplugged it, we have tried every single button, but it continues to only do the 10 minute rinse cycle. What do we do?


... Dacor Epicure ED30 30 in Builtin Dishwasher

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher

Gets to the end of the cycle (1 minute left on countdown) and just keeps running, does not start the "dry" mode. will run until i open it and when i shut it it goes 13 minutes left on the countdown but then gets stuck at 1 minute again. does not drain. has been doing this awhile, but until now it would simply finish the cycle when i opened, closed and reset it. now it just gets stuck again.


Hello,Welcome to FixYa.Based on your description ... Bosch SHU5315UC Dishwasher

Eurotech Model EDW254EWXX runs a 13 minutes cycle before washing like usual, but now it is getting stuck and not doing anything during that 13 minute cycle. No water is running, and it makes NO noise at all. We are not getting any errors displayed. I have unplugged it, and shut off the circuit breaker for 20 minutes, but the problem is still there.


... EuroTech 23 in. EDW254E Built-in Dishwasher

Cycles improperly My dishwasher does not cycle properly. It races through the cycles, even when set to pots & pans, in about ten minutes. At first I thought it not filling properly, checked the fill switch, it's fine and water does come in. Then when it's finished it does not always drain completely. I have checked everything on the drain end as well. It seems to have a mind of it's own. I replaced the $145 computer control with no luck. It actually sped up from the original 16 minute ful


Hi there,\015\012\015\012please let me know the make and full model # off your d/w.\015\012\015\012thanks ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

My top dishdrawer stopped working half fill of water. I put it on rinse cycle and it drained the water. I found a bit of sand in the bottom of drawer. I wiped the sand out and then put onto a cycle. After a couple of minutes the dishwasher started flashing a tap symbol with a slash through it and stopped working. Any help please:) Jacki


... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Dishwasher is not cleaning well, dirty film all over everything, like its not rinsing. In rinse cycle only, some water comes out of lower left port inside but nothing else. Hear a low buzz underneath unit like a motor or pump is energized but no water getting to the top.During normal wash cycle, buzz from underneath seems to cycle on and off, say every minute or so like its cycling on an overload. Do I have a bad pump and if so how do I get to it?


Hi. This may well be a pump issue, or an obstructed hose assembly, as well. Your symptoms are indicating that the impeller may be damaged. In order to pull the necessary schematics, I will need the entire model number. This ID tag will allow me to pu ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

I cannot figure out how to advance a cycle without having to go through the entire cycle. For example, I had a drain problem with my sink and the plumber put the rinse and hold cycle on for about 10 minutes; now every time I want to turn on the dishwasher it is in the rinse and hold cycle. How can I change it???


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Your post doesn`t specify a model number, however on most Bosch dishwashers in order to change from "rinse & hold" to "regular" ( or any cycle ) simply turn t ... Bosch Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

GLD4050 DW won't pump out at any time during wash cycle. Removed lower arm, screen, etc. and washed and cleaned out everything. Removed drain hose and cleaned it out. Reinstalled and ran again. At no time during he cycle does the water pump out. HOWEVER, if I put my hand on the drain pump I can feel and hear the pump running as usual at the right times in the cycle. What else could be preventing the pump out? Thanks!


You could have a plugged pump itself or broken propellers as long as drain and screen are clean which looks like you already took care of that. ... Frigidaire GLD4050RHS Builtin Dishwasher

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

HOTPOINT BF1680 DISWASHER STARTS CYCLE THEN DRAINS AFTER TWO MINUTES SHOWING FAULT ON 1 3 CYCLE LED,S


... Hotpoint Dishwashers

We have an Hotpoint FDW70 Dishwasher that for some time has had an A10 fault which although stops the machine some times 70% of the time it does a full cycle. However it is now tripping out the electric at the mains. It is not RCD protected, but does not blow it's own 13amp fuse or that of the fused extention lead it is pluged in to. Tends to blow after about 5 minutes. I know about the fault code A10 being 'Fill Valve Triac' but as not an engineer what is that? and what parts are needed and or


Hi the fill valve triac is the plastic vlave that the inlet hose connects to you can get them for about £10 you reset the machine after replacing it by switching it on, pressing the power button leaving it off for about a minute then switching ... Dishwashers

We have a Hotpoint DWF31 dishwasher which seems to have a fault in the programmer. On 'Normal (65) and Economy (50)' the minutes to end comes up as '2H' and although I have set it running on both programmes, it doesn't appear to be counting down or performing the normal cycle. On the other programmes it works normally. According to the User instruction book, the programmer is self learning and calculates the minutes to end based on previous use of that programme. Is there any way of resetting th


Hi\015\012\015\012 \015\012\015\012Thanks for using FixYa. Switch off the\015\012dishwasher from the power socket and mains and replace all the cables and\015\012switch it on after five minutes. Yo ... Hotpoint 24 in. DWF32P Free-standing Dishwasher

I have a whirlpool for Ikea dishwasher that is built in and I put it on the normal 30 minute cycle before I went to bed and 8 hours later it was still going. I opened the door and machine was full of suds. It is like it gets stuck and can't move on to the next part of the cycle. I have checked the filter in the bottom of the machine and checked the salt and rinse aid levels.


It could be waiting for the temperature to reach the required level.\012\012Sounds like the heater element has died. ... Whirlpool Dishwashers

Brand new haier hdc1804tw wont start. i press the power button unit beeps once and power light comes on but i cannot select cycles. unit will then beep every five minutes. i have made sure there's water and unit is level. i have left it unplugged for over five minutes with same resulting issue.


... Haier HDC1804TW Dishwasher

My Kenwood dishwasher KDW24FI/B has worked fine for approx 2 years. But now when I put my dishwasher on, the cycle never seems to end. After a few hours of running I opened the door to find the tablet hadn't dissolved but lots of steam coming out. I tried 2 more times and the same thing happened. The pump is working and everything seems ok. After reading the manual I have noticed the salt and rinse aid lights are iluminated. I have never put salt or rinse aid in since I had the dishwasher so thi


Lol is it a stereo or a kenmore, dishwashers dont use salt, but water softeners do ... Dishwashers

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support


... Bosch Dishwashers

Our LG dishwasher (model LD-1416T), age about 2 years, makes a lot of noise. Could it be the motor, anything we could do to fix it? The noise is especially bad after 2 minutes when you put it on for about 3 minutes and then on and off as the cycle continues.


It would have been easier if you had described the noise I will assume it is a sort of clanking noise. If this is so check that the rotating shower arm is not catching on the basket or any part of the insideYou can usually simulate ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1474 seconds