Having problems with your Fisher and Paykel Dishwashers ?

Error code F4, Fisher and Paykel dish-washer?

\015 I have replaced a broken door latch and facia, now unit only completes part of the cycle and beeps with code F4 on display. power was off during repair, has been turned on again, nothing else done - That I know of !!\015

Answers :

Repair Help & Product Troubleshooting for Fisher and Paykel Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Error code F4, Fisher and Paykel dish-washer?


... Fisher and Paykel Dishwashers

F1 code on fisher and paykel dish washer


... Dishwashers

I have a Fisher and Paykel DD605i dish drawer. We have a U1 error code on the top drawer and had this same problem just over a year ago. A repair person replaced the inlet valve I believe. I am wondering if there are any tests I can put the machine through or if this is something I can fix myself to see what is causing this code.


... Fisher and Paykel DD605I Dishwasher

Fisher & Paykel DD603 Error code F2. My top dish draw is showing the error F2 , I have taken out the baskets, spray arm, propellors. The metal shaft is completley frozen, I can't move it at all. I see other posts say to wiggle it to free it but that doesn't work here. Can I get a copy of the service manual too? We are along way from a repair man to come look and I like to try myself before spending more money on it. My e-mail is [email protected] Thanks.


... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

What is error code 00 on dish drawer - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My fisher&paykel 2 double dish washer works just fine no codes come up at but beeps from top one while running and even if it is not in use any time drawer is shut it beeps


If you find the dish wash makes the noise like the draw has been open and its mainly at night you most likely have cockaroaches. The dishdraws have infared sensors to tell it that the draw is open which works like a beam of light. When the beam of li ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

We just purchased a used Fisher and Paykel DS 603-i. After installing and running the normal cycle there was a lot of water left on the bottom of each drawer. We ran the bottom drawer (water stil siiting on the bottom of the top drawer) and part way through the main wash cycle we got what I think was a F1 error code (we do not have the LCD version but the Rinse light was activated). I took out the bottom drawer, dried out the basin and then took out the washer and reattached the drainage pipes t


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You’ll need to reset it by poweri ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

F2 code on fisher and paykel dish washer


Http://fisherpaykelparts.net/index.php?categoryid=115&productid ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Fisher and paykel dish washer keeps running - Fisher and Paykel Dishwashers


It will help to come up with a cause and solution if you can please specify the model number of the dishwasher.\015\012\015\012Also please confirm if you hear the pump motor start during the cycle. How do you stop the dishwasher. Is there wat ... Fisher and Paykel Dishwashers

FISHER PAYKEL DISH DRAWER U3 FAULT CODE - Fisher and Paykel 24 in. DD-602 Built-in Dishwasher


LP is a setting for Low pressure. To reset your pressure to HP, hold the Programme and Eco touch switches simultaneously for 5 seconds. Once the setup mode is entered a beep is emitted andthe LCD is red with ‘HP’ or 'LP' displayed. ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Fisher and Paykel Error code Ho - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dish drawer leaks Fisher Paykel


When water accumulates in the bottom it triggers an error code and it keeps running. There is a water sensor in the bottom. I pull out the bottom drawer, mop up the water and use a hair dryer to dry the water (the more you mop up the less you need th ... Dishwashers

Error code. Fisher and Paykel Dishwasher


Well since you asked on the 5th July, and no reply, doesnt look like you may get one. I thought thats what this site was about?? ... Dishwashers

F1 error on Fisher and Paykel Dish Drawer


Sorry did not see your problem report earlier. If you have checked the sensor under the bottom drawer and it is dry, then F1 is caused by top drawer power filter fault. This means the bottom drawer controller is giving the F1 error but the top drawer ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Fisher Paykel Dishwasher Door Open error code


If it is a dish drawer type there is a clip at the rear of the drawer that holds the drawer closed. you will need to withdraw the drawer partially to look in. with the drawer open the fingers should be facing towards you. If not you will need to reac ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Error code JJ on belling dish washer


... Belling 24 in. IDW603 Built-in Dishwasher

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

F4 error fisher & paykel nautilus dishwasher sometimes this error comes up and it seems to occur about 10 minutes from the end of the cycle. it doesn't happen all the time. the user guide does not specifically address this error code.


F4 is a heating error- dishwasher has not reached temperature in allocated time. If intermittent fault, problem is usually with electronic board, which has temperature sensor attached. Sometimes the wiring to the control board burns out and can give ... Fisher Dishwashers

DS603 Fisher & Paykel U1 error code ..(see our previous errors we've listed) we have now pulled out the yellow water valve that goes up behind the front panel and at the other end by removing the drawer and plastic protector thingy - we checked that there were no bedris or calcium buildup in the valves ends and filters and replaced it all. So we put it all back to gether as we could not see what would cause this error, only to find that it worked - water came into the machine but about 4 mins in


This product is total ****.\015\012Pull it out, call whoever sold the **** to you\015\012and tell the to come get it and shove it up their ***.\015\012Then buy a Bosch and live a happy life.\015\012The design is moronic. The machine is like the old\ ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

Fisher & Paykel dishwasher drawer won't run, beeps F2 error code


Craig, we had virtually the same situation.  The repair man  came and it took 2 minutes to fix.  The problem was that the bottom drawer had not been used for a couple of years and thus the impellor had jammed.  to fix it take out ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

F1 Error code on fisher paykel softouch dishwasher


F1 means that water is in your basepan--- you can pull the bottom\015\012drawer out and soak up the water with a towel... you will have to use a\015\012hair dryer to dry underneath the control sensor in the back left corner. ... Fisher Dishwashers

Kenmore model 17023401 dish washer clean light blinking error code 7. What is this code telling me?


... Kenmore 24 in. 17023 Built-in Dishwasher

What does e16 error code mean on a bosch exxcel dish washer. i am not able to turn a cycle on as this code is dislplayed.


... Bosch Dishwashers

My dishwasher's lid is stuck down and won't retract. I have a Fisher and Paykel DD605 dishwasher, and I think I must have placed some dishes in there that were too big for it and the lid got stuck. It's now showing an F7 error and refuses to do anything other than beep at me. I've tried turning the power off and back on, but it persists with the error. Is there a way to get it to reset and retract the lid? I've read that in situations like this, when people get repair technicians to com


The error code f7 stating that "the communication time out error"this are all the reason for the error1.the motor control micro has crashed and is not responding to communication request.2.the hardware communication link from ... Dishwashers

How do i fix an F5 error code on a Fisher & Paykel Dishdraw DS605. I have turned the power off but the error keeps returning?


I am assuming you have the DD605 double drawer dishwasher. Is the problem F5 on both drawers or just one?\015\012\015\012F5 code involves the drawer lid seal and will need a bit of effort to check and fix.\015\012\015\012Take ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1322 seconds