Having problems with your Fisher DD603FCSS Dishwasher ?

RE: Fischer paykal F1 code

\015 How do I fix the F1 code on a 603 dishwasher\015

Answers :

F1 fault means the flood switch on the base of the dishwashers has been activated.
\015\012nine times out of ten its the lid motors.
\015\012You can remove the two kick plates on the bottom of the dishwasher.
\015\012Dry out the water in the base with a sponge.
\015\012only one draw will be leaking water??
\015\012This allows you to use the second draw until a serviceman shows up.
\015\012Dry the base out A.S.A.P, because you have a electronic board that sits on the base. cheers
I have a dd603ss the bottom drawer is leaking at the top of drawer the seal looks good. the drawer slides are rusted and corroded I think that the lid is not closing all the way and has been leaking for some time on the left side, the side that has water on it after washing. the F1 code alerted me to the situation.
Repair Help & Product Troubleshooting for Fisher DD603FCSS Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

RE: Fischer paykal F1 code


F1 fault means the flood switch on the base of the dishwashers has been activated.\015\012nine times out of ten its the lid motors.\015\012You can remove the two kick plates on the bottom of the dishwasher.\015\012Dry out the water ... Fisher DD603FCSS Dishwasher

F1 code on my Fischer Paykal drawer dish washer . This is the flood sensor . It was. tripped when water was splashed in a plug that shares the same Circuit. How do I reset the sensor?


Not sure if the flood sensor will trip if the water is splashed into the mains plug. F1 can also occur if the power to the top drawer has failed. Flood sensor trips when water collects at the base of the dishwasher housing under the bottom drawer. ... Fisher and Paykel Dishwashers

Fischer paykal dishwasher drawer leaving white powder on dishes


If rinse aid levels in dispensor are ok then check if it is being used. the rinse aid setting may be set too low. ... Fisher and Paykel DD605SS Stainless Steel Dishwasher

I have a Fisher&Paykal DD6031 drawer dishwasher. Stopped running mid cycle. Lights flashing on drawer front green,red,yellow,red green,red,yellow . I don't know what that code means. On the inside Heavy ,fast,rinse were all lit Red. It sings "the star spangle banner" too!


Follow this steps and fix it. GOD BLESS YOU\012 \012 Heating Element\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Bosch SHE44c getting a E6 code????Just finished E1 code by re-soldering the board and the first wash after fixing that error, I get an E6 code and it did not drain. During the repair of E1 code, I cleaned all hoses out and made sure I had no problems...What is the troubleshoot to search for E6 code?


Thanks, that perfectly nailed my problem. Bad / burnt solder joint on a SHX45P05UC/57 model. A little solder, and it may last a while. But next it fails that way I can order the motherboard without even opening it up. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

What does the code NE mean on my LG dishwasher? it gets through about 10 mins of a cycle then bleeps and the code NE is on the screen. I tried putting it on a different cycle and starting again but the same thing happened. ive only had this dishwasher about 5 week, i checked the manual for the code and it isnt listed among the trouble shooting codes there


... Dishwashers

Electrolux 1113312-20 Hi - my dishwasher circuit board has burnt out (melted) and i need to replace this section. The details on the unit state:- Computime CODE: ELE4157 Electrolux CODE: 1113312-20 Hardware CODE: 156050732 SW: DMA24_MR 230V/roHz T65 Date: 09-281 Can anyone help to advise the best place to get one


... Electrolux Dishwashers

My Whirlpool wdf530payw dishwasher is not draining. I ran the service diagnostics using the control panel, and the code that came back was Function code 8, and Error code 2 "Drain Motor Electrical Problem". The possible causes listed are: a. Loose Connection in drain motor circuit, and/or open drain motor winding. b. Open Fuse on control to drain motor c. Faulty drain motor drive circuit on the control When I hit the "Cancel/Drain" button there's an faint buzzing sound for about 2 minut


... Whirlpool Dishwasher. Front Control Dishwasher in White WDF530PAYW

Hello ... We have a GE Quiet Power 3 Dishwasher -- only two years old. Dishwasher won't start ...and we are getting an 1h code. What is a 1h code? The manual does not provide any code information. Thank you!


Hello,Try unplugging the unit for several minutes if that does not fix the issue you will need to replace the main control board to fix the issue, let me know, ... Dishwashers

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

Fphd2481kf control won't reposed. I unplugged it for a few hours to get it to reset. When plugged back in the pf code was shown. I opened and shut door to clear code. U cannot get it to respond to any input and it doesn't show any codes.


... Frigidaire FPHD2481KF Builtin Dishwasher

Pf code came on and then went to er code reset power and pf code comes up then starts showing 37-36


Hi,Here is a tips that I wrote\012that will help to explain why you get the PF Error CodePF\012Error Code for Appliances\012hea ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

U3 code I have a U3 error code on my dishwasher, what does that code mean?


I have had this problem and went straight to one of the F&P engineers... U3 will display because the water did not drain from the previous stage in the cycle... Check the HP/LP settings first as this will give the impression the water did not dra ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Error code LE shown on a LG dishwasher model LDS5811ST and this code is not given on the standard error code list.


Hello JA12345,\015\012Here is a link to the service manual for your dishwasher. Page 25 discusses the error code...\015\012 ... LG Dishwashers

I have an IAG dishwasher that keeps stopping on cycles before the dishes are dry and coming up with error code E7 which asks me to rerun cycle and if code appears again contact maintenance. Any suggestions on what code E7 means


... Dishwashers

I have a whirlpool dishwasher Quiet Partner IV. Every 3/4 months I have to reset it because it will not turn on and perform a wash cycle. The appliance repair people only reset it and charge me $40.00 and do not give me the code. I found the code on the internet but now that code is not working ''High Temp, Air Dry, Air Dry, High Temp, Air Dry, Air Dry.'' Any other suggestions?


... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

Hi, I've got DS 603 single draw dishwasher Ser. No. CPM 739878, It has given a fl code for the flood switch. I have removed the draw and made the observation that the lower steel housing has partially flooded, hence the code. I intend to replace the flexible hoses Input and discharge hose. I am wondering once I replace the hoses, dry the housing and associated printed circuit bourd area should the fault code reset its self or is there further tech. assist required. The draw was manafactured


In the catch basis there is a printed circuit board that contains a sensor that detects moisture. Once throughly dry however, the sensor will no longer sense moisture and the flood code will cease and desist.BUT before replacing the hoses, (alo ... Fisher and Paykel Dishwashers

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

I have the "rinse" error code on my kitchenaid double drawer dishwasher kudd01dppa1. I've turned off the power, then it worked for one load and the code reappeared on both drawers again. What should be a next step? it says in the manual that the "rinse" error code means that something happened to the flood switch...? Can this be fixed without calling out the kitchenaid technicians? thanks


... KitchenAid 23 in. KUDD01DPPA Stainless Steel Dishwasher

I'm getting a PF power interupt code. When I press the "Start/Cancel" button the code goes away. Unfortunatly the unit will not power up. It appears to be completely dead. If I cycle the breaker the PF code comes back and we start the process again. What's wrong, help!! Bob


Hi,If pressing the cancel button doesn't get rid of the power failure error\015\012 "PF" then you have a bad control board. So you will need to replace \015\012the control board itself.You could try to disconnect the power su ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

LE CODE i am having a le code, it says its the main pump motor. i replaced it and still same thing, fills and then does not start,times out 2 or 3 mins and LE CODE COMES ON.


Check whether you have 115/220V on pump's tags.\015\012In case you can't read 115/220V on pump's tags,\015\012your problem could be the water level switch. The switch level is usually a diaphragm device with a small clear tube attached between the sw ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

H:01 code The dishwasher is showing a h:01 code and will not start. What does this code mean?


... Bosch She6Ap02Uc Ascenta Evolution Series 24" Built-In Dishwasher

My Beko DW686 Dishwasher displays ER1 Error Code, there are no error codes in the manual, can you help?


Reset error code 01. pulled dishwasher out removed kick plate \012tipped at 45 deg angle and found no leaks or water. turn ... Dishwashers

FISHER & PAYKEL dd24 , i CHANGED THE ROTOR MOTOR BECAUSE OF THE F2 CODE AND IT WAS BURNT, BUT THE CODE STILL POPS UP AT START UP ?


Need to clean the pump sump and the drain sump to make sure there is no debris left. Most likely a bone chip or seed inside the channel connecting the two sumps. Use a thin rigid wire to clean. ... Fisher and Paykel DD24DCX6 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0506 seconds