Having problems with your Fisher Dishwashers ?

Have a dishwasher which is coming up with an F1 on both draws as soon as you turn the power onto it - any ideas on what to do?


Answers :

Hi,
\015\012
\015\012The major reason for error code F3 is due to some issues with the Tub Seals. Please perform the following troubleshooting to resolve the error.
\015\012Remove bottom drawer you will find water has leaked and the flood switch has been activated. Remove power to unit and dry up tray with towels and hair dryer. Check drain hose and fill valve for leaks. The most common problem I have found is the tub seals. With unit back together and running pull on drawer and see if it comes out. (It should not come out) The boards may be burnt by this point. The bottom tray in the back has a plastic cover over control board, remove cover and inspect board for damage.
Thank you for contacting www.Fixya.com
Repair Help & Product Troubleshooting for Fisher Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have a dishwasher which is coming up with an F1 on both draws as soon as you turn the power onto it - any ideas on what to do?


Hi,\015\012\015\012The major reason for error code F3 is due to some issues with the Tub Seals. Please perform the following troubleshooting to resolve the error.\015\012Remove bottom drawer you will find water has leaked and the fl ... Fisher Dishwashers

Have a Westinghouse 905 dishwasher (guessing approx 5-10yrs old). When I turn it on it's starts is cycle as expected then stops after about 10mins and loses all power (can't turn it on or get any lights to light up for sometime almost like it needs to cool down) at this point the dishwasher is full of water. It is not the pump however as as soon as you can get power to it (sometimes some hours later) and turn it on the first thing it does is pump out the water. Any ideas??


It is likely the thermal relay is tripping. This could be because if you are feeding hot water to inlet the temperature of water is too high, or the dishwasher heater is faulty and overheating the water. Or it is also possible the thermal cutout is s ... Westinghouse Dishwashers

POWER LOST turned off breaker to do electrical work within the kitchen, when i turned power on the dishwasher now will not even come on????? Chekced breaker and GFI, any ideas


... GE 24 in. GSD3620Z Built-in Dishwasher

We have a Siemens dishwasher SE25M851. It had the check water light on, so we have checked all water flows which seem fine. There is what I think is an Aquastop connected to the water hose, which I have no idea if the problem is there, but when I now put the dishwasher on there is a burning smell coming out of it, so have had to turn off power supply. Can you shed any light to the problem?


... Siemens Dishwashers

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

I have a Dishlex Global 300 dishwasher that stopped working mid-cycle. I had to sponge out all the water. Now none of the buttons do anything and none of the lights come on. When I turn it on at the power outlet it gives a single beep, but I cant get it to do anything else. I've opened it up and there is no water or dampness anywhere inside. Any ideas?


It is your control board inside your dishwasher. ... Dishwashers

Dishwasher is just less than 1 year old. it doesn't respond to attempts to turn on. I turned off the power at the box and back on after 10 minutes. it worked. then the same problem returned. now it wont turn on at all. I checked all the connections I could and they seem fine. I know it is getting power. My guess is that something is wrong with the computer system. any ideas?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Maytag 24 in. MDBH950AW Built-in Dishwasher

Hi my siemens hydrosensor intergrated dishwasher has a problem, i set it to come on for 5 this morning but when i opened it his morning the timer was still showing 3 hours so i turned the power button off but now when i turn it on nothing happens, no lights come on or anything


... Siemens 24 in. SE53200 Built-In Dishwasher

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

I have a Miele Dishwasher G1023U , after pressing on/off button the control panel light comes on in the drying cycle not the Wash/Rinse . Water does not come into the machine , can not turn it off at stop/start button only at Main on/off power button. Only had Dishwasher 2 weeks, was working fine. The water tap is on, no kinks in hose.


... Dishwashers

Ex600 diswasher My electrolux EX600 Dishwasher is loosing power during a cycle so I turn the PowerPoint off and then on again and the dishwasher then has power again but "PF" is displayed. Any ideas?


... Electrolux Dishwashers

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Maytag MDBH979AWS dishwasher - there appears to be no power coming in to it. The dishwasher will not turn on and there are no lights on the control panel. I checked the power in the breaker box and it works fine. Any suggestions what to do next?


Maytag MDBH979 power sensor will not turn on dishwasher. The other buttons and lights turn on when pressed but not the power button. Please help. ... Whirlpool MDBH979AWS Builtin Dishwasher

I have a KitchenAid dishwasher, model KUDP02FR. The "normal" cycle light is flashing. When I push "cancel" or "resume/start", they start flashing as well, but the dishwasher won't start. I turned off the power and turned it back on. The "normal" light still flashes, but when I press "resume" it all starts over again. Any ideas? I can't find this in the troubleshooting guide I have. Thanks.


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid KUDI01TBK Dishwasher

The power was turned off and then on again. When the power was restored the dishwasher would not work. The only light that would come on when the door is openned is the heated dry light a ms it would only turn on for a moment.


Hi... you have a bad control board ... Dishwashers

I have no enr number on my Bosch dishwasher just Maxx Classixx. Motor continues to run after programme finnished and comes on as soon as select programme before turning on. Only way to solve is to tip water out of dishwasher each time by tilting back until it comes out.


... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

We have just moved into this unit fitted with a MIDEA WQP12 - 9011B dishwasher with NO MANUAL. What can we do ? We have been using the dishwasher by turning the operating KNOB to a position and pushing in the POWER KNOB. The machine then goes through a cycle of 80 to 100 minutes but without an USER OPERATING MANUAL, we have no idea of whether the dishwasher is being operated correctly.


... Dishwashers

I have a single draw Fisher and Paykel dishwasher. I stupidly put washing up liquid in the dishwasher which resulted in a F1 problem. Water started leaking under the draw and onto my floor. I turned the dishwasher off at the power point and have cleaned up the leak. Have I damaged my dish washer? How do I fix it?


Ok , F1 means your flood switch has activated, which is underneath the drawer. now they show the F1 fault because of 2 reasons.1st there is still water underneath drawer causing switch to activate. 2nd your activator board which has the flood switch ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

We have a Maytag Quiet Series 300 dishwasher (#MDBTT 60AWB) that is in a house we recently bought. A few days ago it worked, but now it won't turn on. We checked the plug that goes into the outlet and it is plugged in. Yesterday we did have a plumber come out and unjam the garbage disposal. I don't know if that could be the source. Is there a reset button on the dishwasher? Basically there is no power going to the dishwasher. Any suggestions?


... Maytag Dishwashers

After a power outage, my GE monogram dishwasher beeps continually. The controls are not responsive. I've tried turning off the power to it (by the fuse box) but the noise resumes when the power comes back on.


Unfortunately, if you lost power as a result of a lightning storm or a power surge, there is a good chance that your dishwasher was exposed to a power surge that may have damaged the control circuitry. During these types of events, there is no way of ... GE Dishwashers

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Miele G894SC Dishwasher. Flashing LEDs on front pannel. Power cycle no help. The following LEDs are flashing. Top Solo,End,Start/Stop. Recycled power, turned on and off via power sw. all to no avail. Leds continue to flash when pwr is restored. Ideas?


... Miele Novotronic Elite G856SCV Elite Built-in Dishwasher

Leaking FDW60 I have a Hotpoint FDW60 dishwasher. yesterday it tripped our house electrics and then we had water flooding out of the dishwasher. Through a process of elimination I have now discovered that water is leaking from the drainage sump in the centre of the babse down onto the motor or other electrics. I have looked for loose hoses and there are none visible from the base of the dishwasher, can you give some ideas where the water might be coming from?


Had a similar problem when I removed the lower spray arm for replacement (see http://www.fixya.com/support/t234402-fdw60_dishwasher ) and didn't put the centre retai ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

The dishwasher trips the safety switch in the meterbox. whirlpool ADP 5000 made in germany (not on the drop down list) the 1st time was after a finished cycle and the power was off in the morning. the second time the power was on at the wall and when thw nob to select the cycle was turned, the power went off. any ideas would be really appreciated. julian


\015\012Please DO NOT touch this machine IF the power is ON. There is a possibility of shock. The reason, the ONLY reason, that the Breaker "Trips" is, if there is a, Phase fault to Earth/Neutral, in other words the CA ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2271 seconds