Having problems with your Fisher DS603W / DS603B / DS603I Dishwasher ?

The rinse cycle does not seem to want to come to an end and start the drying. we need to switch it off at the wall


Answers :

Repair Help & Product Troubleshooting for Fisher DS603W / DS603B / DS603I Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The rinse cycle does not seem to want to come to an end and start the drying. we need to switch it off at the wall


... Fisher DS603W / DS603B / DS603I Dishwasher

I have model 363.14779100 that has a problem. When a drain cycle is at the end and the fresh water starts coming in, the draining won't stop therefor all clean water goes right back out the drain. I can open the door latch and reshut it and the cycle will complete but the same thing happens on the next drainout. Is there a switch that needs replacing??


... Kenmore Dishwashers

Hello. I have a Kitchen Aide KUDG255HWH1 that will not start from a cold state. The "Energy Saver Dry" and "Normal" indicator light/ switches failed to operate about 1 month ago and since then I have needed to use the "High Temp Wash" and Soak & Scrub" cycles to get the unit to run. Now these two indicator kight will illuninate but the unit will not start when I depress the "On" soft switch. When I depress the cancel switch the unit starts with what sounds like a pre-start cycle. Pleas


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. To reset the dishwasher switch\015\012off the dishwasher from the power socket and mains for five minutes and then\015\012switch it back on. If still the issu ... KitchenAid Dishwashers

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

The GE Profile Dishwasher will not allow me to start without the heated drying light coming on. I want to wash without this headed drying at the end of the wash. When I try to turn it off it turns the start cycle off. This happend over and over again when I want to turn on the machine, It finally lets me get an unheated dry wash started to complete. A problem every night. PDW7800N15CC. Serial MM8243388


... GE 24 in. Profile PDW9800J Built-in Dishwasher

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

The items on the top rack never come out clean. there is always food residue left. it seems that the final rinse doesn't get to the glasses. we need to rinse them all out before the drying cycle starts or else the dirt dries up inside the glasses and we need to make them soak to remove the dirt!


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... Amana 24 in. ADB2500AW Built-in Dishwasher

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

W10199645 The lights for type of cycle and drying type come on but the start light wont come on, NO WASH. Checked to be sure there was water pressure, checked the latch switch, both OK Help


... Maytag Dishwasher

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

Bosch Dishwasher Cycles will not stop running. They keep starting over. Help please!! Our 2 year old dishwasher will not stop running. It gets to the end of the cycle and starts over again. Plus, the cycles seem to have gotten longer. We called the Bosch repair number and they want $150 in cash to come out and look at it. Then they will come out and fix it!!!! Unbelievable!!!


Carry out a reset.\015\012This should reset the board back to factory settings,\015\012Deep Diver ... Bosch 24 in. SHU5305UC Built-in Dishwasher

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

When i push the start button,it doesn't light up and start. The normal cycle and the other cycles lights work but it won't start. If i push hi-temp wash and heated dry several times, all lights will come on but when i try to run it through a cycle, it won't start.


I would replace the key pad it sounds like since everything else works.. so you hit the normal wash and start the dishwasher sits there for a min or two and turns off.. Its not recognising the start button ... Dishwashers

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a Beko DE2431FW Dishwasher which has stopped working. I select a cycle and then press start, the green light starts to flash and the cycle begins to start but after about 30 seconds it stops and the red 'end' light comes on. this happens no matter what cycle I chose. Can anybody help me with this please?


... Dishwashers

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

Cycle starts, soap box does not open. Cycle will repeat with water running for hours on end. No end to cycle or drying cycle. Checked inlet, outlet and tried reset.


Hello Paul,\015\012\015\012\015\012There are a few possibilities here but I really need a little bit more detail from you and you're going to need to do some testing to determine the cause of the fault - or faults. You're going to need a ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a General Electric pdw7880J03ss dishwasher. Tonight, I went to start a load of dishes and the Heated Dry option wouldn't turn off without the lights going to RINSE ONLY. Then the 1hr setting started coming on. Then was able to get the load to start but then it stopped somewhere in the cycle. Now, no lights will come on the panel though I can hear the beeping. Dishes appear to have washed...


Hi\015\012\015\012Press and hold the heated dry button for 15 seconds to reset\015\012the control, if this wont work then it means that the control board is bad and\015\012should be replaced. Hope this helps...please post back for further ... Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

Danby ddw1805w dishwasher doesnt cycle. Timer switch does not respond to any commands or move through cycle or turn off when forced to end of cycle. Need help. I contacted Sears parts direct last week and this week they've told me that they dont have the part afterall. Need a repair fast. I am technical and can fix it myself if necessary.


... Danby Dishwashers

I have a Bosch dishwasher she44c05uc/40 It is 3-4 years old. Recently I noticed that the cycle times have gotten much longer. Since then there is a sewer smell in the washer especially when starting a new cycle it comes out of the disposal. I'm wondering if the pump isn't heating the water hot enough. I've also noticed that the dishes aren't getting near as clean as they were before all this started. Especially stuck on food. It used to clean everything now dishes almost need rinsed.


Hello,Welcome to FixYa ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1967 seconds