Having problems with your Frigidaire 18 in. FDR252RB Built-in Dishwasher ?

18 inch dishwasher does not have any water

\015 18 inch dishwasher does not seem to be getting any water during any cycles. Water valve is turned on.\015

Answers :

HI. This is a water inlet valve issue. I recommend testing this device. it may be faulty.

To access the inlet valve remove the lower panel located beneath the door. The panel is usually held in place with two screws either above or below the panel. It may be necessary to first open the door to the dishwasher to reach the screws over the panel, then close the door to remove the panel. The water inlet valve can be identified by the water hoses connected to it. One hose will lead from the valve to the pump/motor assembly in the center of the dishwasher. Check that the hoses are securely connected to the valve and that there are no kinks in the hoses which could restrict water flow. There are two wires (four, if it has two solenoids) connected to the water inlet valve. Label the wires and connections so that you can properly reconnect them later. The wires are connected with slip on connectors. Firmly pull the connectors off of the terminals (do not pull on the wire itself). You may need to use a pair of needle-nose pliers to remove the connectors. Inspect the connectors and the terminals for corrosion. If either is corroded they should be cleaned or replaced. Use a continuity tester or multimeter to test for continuity. Set the multimeter to the ohms setting X1. Touch one probe to each terminal. A reading of infinity indicates a bad solenoid that must be replaced. Different brands and models will have various measurements, but the valve should show some resistance if it is functioning properly. If your valve has two solenoids, test the second one in the same way as the first. Replace the valve if it fails the test.
Repair Help & Product Troubleshooting for Frigidaire 18 in. FDR252RB Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

Re: Bosch Dishwasher Model SHX46B06UC/14 (year 2003) Good afternoon, I have water dripping into my dishwasher when it is not in use, approximately up to 1/2 inch over a few hours. The water collects at the bottom inside the dishwasher. I have to shut off the dishwasher water supply so that it does not overflow. Other than that, the dishwasher works perfect! Any idea as to what has to be replaced? Can I do it myself or do I have to call a technician. Thanks very much for your help.


HI. This type of issue will be the result of mechanical failure. This failure will be within the inlet assembly. Debris may be keeping the solenoid valve from closing correctly, thus, producing the steady drip a ... Dishwashers

Dishwashing machine not fully draining (2 inches of water remain). I have an open problem concerning this problem. I have a new pump. dishwashing machine not fully draining (2 inches of water remain) For this machine.


Following a cycle, a small pool of clean water inside the tub is\015\012typical. Excessive water means the pump isn't pumping water out\015\012properly, the drain hose isn't carrying it to the drain pipe, or the\015\012house's drain lines are backed ... GE 24 in. GLD5860LSS Stainless Still Built-in Dishwasher

Our Hotpoint Dishwasher Model HDA200X-73BA has two little white plastic pipe stubs poking out of the bottom of the dishwasher. During one of the cycles--(I don't think it is the drain cycle)-- some water is being released from one of these pipe stubs and then it stops and the other one runs some water. They each only run for a few seconds, but the water is just running on the floor. These little pipe stubs are about one half inch in diameter and project out of the bottom of the dishwasher about


Hello. go to the sears direct website, click on the blue link below, and enter your model number. ou can then access an excellent parts diagram which will show these stubs and what may be missing from them. Joe\015\012\015\012 ... Hotpoint Dishwashers

When we do not use the dishwasher for a week or more water seems to back up into the tub. The water has a foul smell to it and can be as much as an inch or so deep. The dishwasher drain hose is attached to an insinkerator disposal. By the way this dishwasher is only a couple of months old and we have had to have it serviced three times. No one has been able to explain the water accumulation and it can not be demonstrated unless the washer sits unused for a while.


... KitchenAid KUDS40CVSS Builtin Dishwasher

Leaky Dishwasher I recently moved into a new house that has a brand new Magic Chef dishwasher. We haven't even had a chance to use it, but last night discovered water leaking from the bottom onto the floor. When I opened the door, there was about 3-4 inches of water inside. I baled as much of the (slimey) water out as I could, and that stopped the leak. Now afraid to run the dishwasher for fear that it might leak even worse. E71195 Type 777-0


... Magic Chef 24 in. DC4000 Free-standing Dishwasher

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

I have a DU8000XX6 series Kenmore dishwasher that won't drain the water properly. There is about a half inch of water in the tub and the float is raised (not sitting on tub bottom). When I lift up the float a little more I can hear the float switch make. I would assume that when the water is high enough the float switch makes and energizes a solenoid valve in the drain to drain the water, but shouldn't it stay open until all the water drains? Lifting the float while the dishwasher is off wo


... Kenmore 24 in. 15142 Built-in Dishwasher

Bosch dishwasher Over the weekend my drains backed up into the dishwasher. After cleaning the drains I ran the dishwasher 3 times. Under the screen there is still about an inch of water. I never noticed this before because I never removed the screen before. Can you tell me if this is normal or is there a problem with the dishwasher. The water in the little area below the screen is clean.


Its normal. its there to keep moisture around the rubber seals so they dont dry out. ... Dishwashers

Whirlpool dishwasher: Model DU920PWKT0; 8 years old Lately, have noticed not full drainage of water at end of cycle... about 1 inch standing (thus 2 inches at the sump). Glasses have had noticeable film on them. Ran the rinse cycle a number of times to explore problem. When I interrupted the cycle, the water on the bottom was soapy, yet no new soap had been introduced. I even colored the water "left" in the tub to see if it was replaced by fresher water. Although it was going through t


Find the 'tech sheet' behind the front 'kick plate' of the machine. This doc will give you a troubleshooting procedure for that specific machine. Check drain line and make sure it's clear and not kinked. Is filter clean?Has machine ... Dishwashers

Hygena Dishwasher My dishwasher does not drain the water away properly. About an inch of water lies in the bottom after a cycle. Incidentally, when I put it on a "cold rinse" (which is the only other setting to "wash 60c") it rinses with hot water. Is my switch and my pump broken or is there another possibility?


I would check for blockage, can you hear the pump trying to drain.\015\012pull all the metal pieces ouy and have a look. ... Neff 18 in. S5943 Slim-Line Built-in Dishwasher

Kitchenaid dishwasher - small pieces of food are left on otherwise clean dishes. Water level comes to about 1 inch below heater coil. I ran it without dishes (or soap) and added about a quart of water so that level came to about 1/4 inch below heater and that's when I noticed food pieces on drain surfaces (nylon filter under bottom spray arm unit and circular plastic "trap" surrounding it). Spray arms holes are clear and water is hot.


It sounds as if you figured the solution out. The holes in the spray arm(s) get plugged by small debris, (tooth picks, seeds, bits of plastic like candy wrappers, etc) and the water does not reach the dishes to wash and rinse effective ... Dishwashers

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

Seems my drain is plugged on my dishwasher it is the magic chef 4500b unit and i now have water all over my kitchen floor. i cant seem to find the product du4500b  so i entered the du2000 , either way there is water on my floor and about 4 inches of water in the bottom of the dishwasher


Ok there are several problems this can be caused from...1. there is usually a float device (I'm not sure about this model) that floats up and turns the water flow off when an appropriate amount of water is injected into the DW...sometimes these ... Magic Chef 24 in. DU2000 Built-in Dishwasher

Dishwasher i have fixed the fridgadair dishwasher so that i can see what it is doing with the door open; water is coming out of the spinner arms but the arms are not spinning ; it seems that water sprays about 4 inches in air; the top is feed water off and on but not constant.


  This dishwasher does not feed water to top and bottom arms at same time.  It starts with bottom and then after awhile it switches to top and then cycles.  If water comes out arms but arms won't turn,  check all holes in arms.&nb ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Hello we are having a problem with our Maytag stand up dishwasher. The water is not pumping out all the way and the water that is pumping out is pumping out slow. There is about an inch of water that is laying in the bottom of the dishwasher.


... Maytag 24 in. MSE760FAKS Free-standing Dishwasher

G.E. GSD5130 When the dishwasher is pumping out the water a small amount comes in the rotating sprayer head. At the end of the cycle the dishwasher still has water in the bottom. The amount of water varies from just a little to over an inch. I replaced the spring loaded check valve a couple of months earlier and everything worked fine until now. What should I check? Thankyou.


Mike, I just ran into the same problem. I found a second check valve located in the outlet hose of the ELECTRIC drain motor. This motor is located at the right rear underside of d/w and is used only for backflush of the filter. When the unit goes th ... GE GSD5130 Dishwasher

Water does not completely drain? Garbage disposal is functioning properly and hose from Kitchen Aid dishwasher to Garbage disposal is good. I ran the dishwasher a couple of times start to finish for rinse cycle and approximately 1/2 inch of standing water on the bottom. Any ideas? Please help. Thank you.


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

Good morning! My Whirlpool dishwasher (I'm at work so don't know the precise number) leaves about an inch of water at the bottom after washing. I called a Whirlpool representative soon after my purchase (post Ike devastation of previous dishwasher that drained fully) and was told that this was rather normal for Whirlppol. I live on Galveston Island in Texas, and adding any more sources of water and humiditiy to my household seems counterproductive. Is there anything that I can do to cause


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Dishwasher drain is hooked to a food disposer and until recently the unit worked fine. Last week following a cycle a couple of inches of water did not drain out. All food is removed from dishes, silverware, etc. prior to loading and the food trap in the bottom is completely clear. I ran the unit empty through a Lightwash cycle and afterwards the water level (that which didn't drain out) looked to be the same as before. The dishwasher is run 2-3 times weekly whereas the food disposal is


Hi, The I don't think the problem is with the loop and the 32" above the floor.If the dish washer was removed from one house to another, did *********** ever have a dish washer in the house before that he replaced this one with? The reason I am aski ... Dishwashers

My hot point dishwasher is not draining,after all cylces are complete there's always 2 or 3 inches of water on the bottom of the washer, what is causing this? I have a Hotpoint dishwasher 24" built in. The switch won't come on just hums. When I oprn the door ther is 2" of water on the bottom? Any solutions . Where is the reset button on serial number hda430vww, hda400vba> Thank you!


... Dishwashers

My Bosh SHX33MO5UC built in dishwasher does not empty. There is about one and a half inches of water left in the dishwasher at the end of the cycle. The water does not seep in after the cycle ends but just does not completely empty


Hi,\015\012\015\012\015\012The drain hose can cause the dishwasher to fail to drain properly. The recirculation hose can be responsible for problems with poor rinsing of dishes.To access the drain hose remove the lower panel located benea ... Bosch 24 in. SHU43 Built-in Dishwasher

My water is not draining from my dishwasher. it has 2 inches of water in the bottom after my wash cycle. it is even throughout the bottom, so my dishwasher is balanced. This is a brand new washer.


If the drain line is connected to a disposer, check to make sure the plug has been removed from the disposer. (typically, the plastic plug inside the tube where the drain hose connects onto disposer needs to be knocked out) If this OK, look for a k ... KitchenAid Dishwashers

Dishwasher repair Dear Guru, I hope you are well this evening. I have a Whirlpool Quietwash Plus dishwasher (940 Series) that will randomly have water sitting in after running through a washing cycle. In addition, some mornings there will randomly be a couple inches of water sitting in the bottom without every running the washer. Need assistance. Any help will be appreciated. Thank you for your time. J


Without model unablr to look up exact unit, but in genreral, either ther is a blockage/clog in oyour drain line not alowing complete drain of cycle, as far as never really washing, i would look into perhaps a faulty/ sloppy door switch assembly. if f ... Dishwashers

Meale dishwashers I have just moved from one house to another. my new house has a one half inch water supply my old houe had 3/4 inch connector When I hook up my dishwasher the indicator light comes on and the washer will not fill. ????????


Check that you have water supply to the pipe that connects the dishwasher to the wall, \015\012\015\012when you switch the dishwasher on, dose it buzz quietly, if so there is no water coming to the machine, the fault is with the plumbing, if there is ... Miele 24 in. G646SC Plus Free-Standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1753 seconds