Having problems with your Frigidaire 18 in. FDR252RB Built-in Dishwasher ?

Dishwasher i need help either installing for troubleshooting my 18' portable frigidare dishwasher. when the dishwasher is turned opn and it starts to fill the water flows out of the bottom of the machine what is the problem and how dod i fix it is it the hoses ? it also hooks up to the sink it isnot a built in dishwasher so is the hose for the draining need to go in the sink or does it hook up somewhere under the sink?


Answers :

I would put the dishwasher on its back so you can see underneath to check the fill and drain hose to make sure there not damaged in any way to cause it to leak. if it all looks good under there return it upright and remove the front lower kick panel grab a flashlight and start the dishwasher. you shoud be able to see a leak and where it is comming from. its possible it could be from the hose the inlet valve the pump and motor assembly or the plastic tub itself. good luck
Repair Help & Product Troubleshooting for Frigidaire 18 in. FDR252RB Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher i need help either installing for troubleshooting my 18' portable frigidare dishwasher. when the dishwasher is turned opn and it starts to fill the water flows out of the bottom of the machine what is the problem and how dod i fix it is it the hoses ? it also hooks up to the sink it isnot a built in dishwasher so is the hose for the draining need to go in the sink or does it hook up somewhere under the sink?


I would put the dishwasher on its back so you can see underneath to check the fill and drain hose to make sure there not damaged in any way to cause it to leak. if it all looks good under there return it upright and remove the front lower kick panel ... Frigidaire 18 in. FDR252RB Built-in Dishwasher

Not getting enough water flow into the dishwasher, suspect that a filter is clogged due to recent work on the waterline in the kitchen sink. Need to know where the filter might be located (on the dishwasher or on the intake valve before the connection to the dishwasher hose)? Also would I need to disconnect the water supply to pull out the dishwasher for access to such a filter.


You didn't specify a brand but most dishwashers don't have a water "filter." They may have an inlet screen at the water valve, which is typically located under the dishwasher. Generally, the lower front panel will have to be removed and you should ... Dishwashers

I have a Bosch dishwasher that was working just fine until I spilled a bag of uncooked pasta. I sent the pasta down the drain and ran the garbage disposal, subsequently clogging the pipes. I had to get a plumber to fix the drains, but he wouldn't unclog the dishwasher. I have tried myself to go under the sink and drain some hoses, but it didn't work. I also put some baking soda and vinegar into the drain, but no luck. What can I do?


It may simply be where the dishwasher drain attaches to your garbage disposal. There should be a hose clamp and can easily be taken off. If the clog's not right at the connection, chances are it's far. If there is an air gap, it will be within a f ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

I need the steps to change the hose assembly on my Whirlpool portable dishwasher. When I got it someone had cut the sink connections off so my son connected it to the water and drain with my washing machine which was in the kitchen. However, I have moved and want to use it as portable. I purchased the new hose assembly for the sink faucet, I just need instructions on how to take the dishwasher apart and connect the new hoses.....HELP PLEASE!


... Whirlpool 24 in. Portable Dishwasher Dishwasher

I had a draining problem, clogged line, fixed. Does the small in line rubber valve under the dishwasher in the transition piece to the hose have any real need to go back? and which direction it is cupped slightly. Also are there any assembly instructions? I cant seem to get it back quite right, or a white washer has split. not sure which.


... Whirlpool 24" Built-In Dishwasher - Black-on-Black

Need a new sink- now THE SINK has 4 holes to accomodate hot cold water faucet and an air gap thing that is hooked under the sink to dishwasher and garbage disposal- can we not rehook that air gap kit and just get a sink with three holes for faucet only?? a quiet wash whirlpool model DU7800XS_3 -need info. linda


Yes you just need to run the hose to the top of the counter hieght to create a high loop. Basically does the same thing as an air gap. Here is a video showing this\015\012 ... Whirlpool GU2400XTP Built-in Dishwasher

Portable Dishwasher I have a older model portable dishwasher. It works great and until it goes out I would like to keep it. I am wondering how or what I will need to make the dishwasher a non-portable. I get so tired of moving it across the kitchen floor. Is there anyway I can hook something up to my lines underneath the sink so it will stay where it is? it is only about 10 ft away from my sink but that it alot of moving around when it is full of dishes. Please help. [email protected]


I sent you and email with some instructions, Look to hear from you soon!! ... Kenmore 17252 Free-standing Dishwasher

I own a build-in LG Stainless Dishwasher (modle: LDF1178ST). It stopped draining water during its recent startup due to its idle (no operation) for about a year:). I can only feel the hose full of water by touching the drain hose between the washer and the sink desposal. It's hard to check other part of dish washer since it's built in our cabinet. Could any dishwasher expert help to advise how to trouble shoot or fix this problem. Thanks, Alex Chen 571-220-7484


There is a float in the bottom of the dishwasher that tell the motor to turn on and pump out the water. I would check the float first to see if it is hung up and not raising to tell the dishwasher that there is water in the base. Check the check valv ... LG Dishwashers

I have a Kitchenaid imperial 21 dishwasher that hooks up to the sink. The smaller of the two hoses that connects to the sink was rubbing on something inside and got a small hole in it causing it to spray everywhere. What I am looking for is schematics and the name or number of that hose.


... Dishwashers

Hi I run a restaurant and have just purchased a used Hobart Hi-Temp Dishwasher but it came without a manual and I want to hook it up. the model # I can make out is AM-12 it also came with a booster, could you give me a parts list of hook up and also is this a 3 phase or 1 phase and what is the amp load what conductor cable to use, sort of info I need Dale


Since your question requires a lot of typing i.e. complete manual which is not feasible over here. Hence, I am offering few links from where you can get your owners manual. Hope this will solve your problem.\015\012 ... Hobart Dishwashers

Our dishwasher had to be removed. In reconnecting it to the water supply under the sink, the plumber could not keep it from leaking. I think there was a rubber washer that got lost during the disconnect/connect procedure. He then proceeded to gut off the end of the PEX hose which has a ridge and the last 1/2 inch is a little smaller than the hose. Now he says we need to order a new PEX hose from the factory. The PEX hose is too big to fit into the fitting. Cannot a normnal flex hose for thi


... Dishwashers

Bad smell This is more of a general question. When I run the dishwasher there is a bad smell as it fills with water. It comes out of the sink/garbage disposal. I have cleaned out the line that comes from the garbage disposal to the drain and that doesn't stop the smell. Is there a line that needs to be cleaned from the dishwasher to the sink or how can I fix this issue? My dishwasher, at the drain, has water standing and it smells. I think it is there from condensation as the dishwasher, unknow


Smell is not the fault of the dishwasher but your waste disposal unit - they stink!it may be awkward, but arrange your drain so that there is a water barrier. better still. install a standpipe for the drain, again with a water barrier ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

I have an older Bosch dishwasher I just hooked up in my condo. WHen a cycle is done there is no water is located at the bottom of the inside of the dishwasher, yet 2 days later water will drip on the floor (with the dishwasher door closed) and I'll open the dishwasher door and therewill be 2" of water at the bottom. The flexible water discharge hole located in the sink base is located at the top of the base cabinet, and the hose runs completly 100% downward from that hole to the garbage disposa


When you empty you sink, some of the water is going down the drain hose of the dishwasher. take the drain hose up as far as possible in a swan neck ... Dishwashers

We just hooked up our old built in GE dishwasher and the water is shooting out the left side of the unit where the black water hose enters the tub. Shouldn't the water be entering into the wash arm? The hose isn't clogged. It attaches to a white plastic piece that is part of the unit itself. The water is entering both the tub but also shooting out of 2 slits approx 1 1/2" each. located right below where u attach the hose.. Any help would be greatly appreciated!


... GE GSD5130 Dishwasher

Hello there, I have a Bosch Logixx dishwasher which I purchased just over 2 years ago. My upper dishwasher tray is not fitting properly into the hose pipe holes on the inside of the back wall of the dishwasher. It has a movable plastic mechanism sort of fitting which is dropping off everytime I open the tray to keep the utensils and unable to close it fully until I re-adjust the plastic to fit into the holes proeperly and then it works. I am not sure how to fix the problem, do I need an En


Hello Deepak,\015\012\015\012You can definitely fix this yourself, but I'm not entirely sure from your description which part is "dropping off". It may be a simple fix where something needs to be clipped back into place or you may need to ... Bosch 24 in. SGS69L02 Logixx Built-in Dishwasher

Plumber fixed the sink, now dishwasher is broken


Sounds like the water is off, too coincedantal to brek after the plumber is there, the hot water under the sink is where the water supply to d/w is. obviously youre hot water at sink is working, there shloud be a sperate on/off valve for the d/w some ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

I have an Asko 1805 Dishwasher. I've looked at some of the other responses and have this sinking feeling after tonight's series of unfortunate events. Tonight, I pushed on the On/Off switch on the left and it appears to have broken. The dishwasher no longer turns on. If you push in and hold the button, the lights come on, but when you let go, they turn off. This appears to be Part 763255 on RepairClinic.com. I also need the overlay/decor insert across the top of the control panel which app


Hello Rick,\015\012 \015\012Welcome to FixYa.\015\012 \015\012The "very instructive, but poor resolution" info you've referred to in your post was indeed a previous solutio ... Asko 24 in. 1805 Built-in Dishwasher

Asko model 1385 dishwasher. When running, water came out all over the floor and is not entering the dishwasher. Also bubbled up in the sink. Seems like there is a clog somewhere. How do I fix it?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Do you know if your dishwasher is draining into a food disposer/garberator, or directly into your home plumbing ?\015\012\015\012This is key to pr ... Asko 1385 Dishwasher

I have at least 2 inches of water remaining after a wash cycle in my Frigidaire dishwasher Model # FDB636GFS5. So far I have just checked under the sink to see if the hose connection was crimped. Do I need to pull the dishwasher away from cabinets to check?


Somewhere there is a slight clog. could be in your hose,drain pump or inside where the filter is.check those spots then manually drain your unit. ... Dishwashers

My dishwasher spray arms were clogged with calcium buildup so I cleaned one and replaced the other. I also removed the fixed disc-shaped device underneath the lower spray arm and found the particle filter was clogged- so I cleaned it out. The dishwasher ran fine for a few times but then the filter clogged again, and again, and again. Now I need to make a routine of disassembling the parts to get at the filter every week because the filter no longer clears itself during the wash and/or emptying c


You may want to check your hot water tank. It may need drained and cleaned, Or you may have the rod in the tank disintegrating. Also check you water faucet areators to see if they have calcium pieces too. ... Maytag Dishwashers

My dishwasher leaks water from the top of my sink when in the drain cycle mode causing a mess on the counter top. How do I stop this leak? The plastic cover to the part which is located next to the faucet is cracked but there appears to be no leaks on the hose or on the part itself. Also, what is the purpose of this part? Is this the actual drain for the dishwasher and if so, why doesn't it tie directly into the drain?


... Whirlpool Dishwashers

I just bought a simpson silenco 850 dishwasher & my son picked it up & took it to the property to install it .He said the waste pipe hose was missing the rubber end with the silver clip to hook on .Do I need to buy a new hose or could I find another rubber piece to slip over & re-attach the clip? Thanks


... Dishwashers

Dishwasher My dishwasher is accumulating water on the floor of it and not being drained out. What do I need to do to fix this problem? Also, what is the average time for a brand new dryer to dry clothes? Any suggestions are appreciated.


Dishwasher: I'm assuming you are talking about when the dishwasher is not running. Correct? If the dishwasher accumulates water while sitting idle, it could be a couple of things. The water inlet valve could be leaking by, or you may have an impr ... Kenmore 15129 Built-in Dishwasher

The quick connect that hooks up to the faucet does not stay hooked up and leaks on our kenmore dishwasher model # 665.17822000 do i need a new hose and quick connect


... Kenmore Dishwashers

I have a whirlpool dishwasher thats a quiet partner 2. the cancel drain light keeps blinking and nothing else is happening. i try to unlock it and then the normal light starts blinking also and still nothing happens. i called a local repair shop and they said i need to change the control board so i did and its still does the same thing. can you give me an idea of where i need to start to fix my problem?


Can you here the pump running or check to make sure there is no water in the base... ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2111 seconds