Having problems with your Frigidaire 24 in. FDB1050RE Built-in Dishwasher ?

The lights are on as Normal

\015 It does not fill with water and does not seem to run at all. It is just a year old??? The hot water pressure seems good.\015

Answers :

Remove power at the dishwasher go to the breakerbox and, flip the dishwasher breaker off
\015\012then when you know the power is off (the lights are off) remove the philips screws on the front top inside door this is the locking lever the cherry switch pins must be pushed in (click) to allow the dishwasher to work you should see the problem easily (burned door switch, broken lever etc).
It could be the solenoid valve on the water line. If the pressure is good, and there is no water, either the solenoid valve is stuck closed or it's not getting the siganl to open. Lack of a signal could be loose connections or a bad chip/board. If it's a bad board, I fear a service call is in order.
Repair Help & Product Troubleshooting for Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

The three lights for Pots & Pans, Normal Wash, Econo Wash are all flashing. When I hold the start button down for four seconds, just the Normal light is on. However, once I close the door, all three lights are on again, and the dishwasher does not start. We have tried unpugging it and then plugging it in again. It worked once then went back to all three light flashing. Before this, only the Normal Wash and Econo Wash lights were flashing.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I can't seem to access any previous post dialog that may have taken place but I'd like to help if you can fill me in on whats taken place to this point.\015\012\015\012The scenario you describe i ... Viking DFB450 Dishwasher

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

I have a Kitchenaid Kudioflss2 dishwasher.The normal cycle light on the display will not go off. None of the other lights will go on. I've completely disconnected the key pad from the unit and have shut off the power. None of the buttons are stuck down. I tried alternating between two buttons normal ,cancel,normal, cancel etc. and a few other combo's.The manuel under the kick plate is missing.Should i just buy a new keypad(part that lights up) or could it be the interface(part where all the wire


... Dishwashers

Normal light flashing on and off. Pressed cancel, now both normal light and cancel light are flashing. Dishwasher won't start. Can't shut lights off. Tried disconnecting power. Lights still flashing.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. To resolve this you will have to\015\012reset the console. Do this by closing the door and press t ... Dishwashers

Dishwasher DU1100. Odd behaviour during cycle: "Washing" light goes off and sound of washing stops. "Normal" light starts blinking and "soak and scour" light comes on (it was off before). No sound from washer. This persists for at least 10 hours. After that, the lights go off. Is this normal behaviour? It would appear tha the drying cycle did not go.


No it is not normal. It appears that either the membrane switch pad has failed or the control board has failed. ... Whirlpool Dishwashers

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


... Whirlpool Dishwashers

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

Whirlpool GU2300 Dishwasher. The machine stops for long periods during the cycle. All lights go out. If the machine is opened before the cycle finishes, it will not resume. If I try to restart, the normal wash light begins flashing. If I then try to cancel, the canel light and the normal wash light flash.


I have reviewed your problem with the Whirlpool GU2300 Dishwasher and have the fallowing suggestions for you.\015\012First, unplug the power to the unit and let it sit for a few minutes. This will clear all internal error messages ... Dishwashers

I have whirlpool diahwasher ,model DU1055XTSQ3,quiet partner -1. when i start the machine the folowings things happen: 1.the machine does not start . 2.Start /resume light starts blinking ,after few seconds ( 40-50 seconds), the pots and pans light also starts blinkng .after some time ( 1 minute ) the normal light also starts blinking .All three lights start blinking 3. I have done the following to rectify the problem from the book : alnernatively pressed heated dry and normal keys for


... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

I have a whirlpool quiet partner II dishwasher model # DU1055XTVB5 and the normal light is steady flashing I have did the sequence to reset HEATED DRY NORMAL HEATED DRY NORMAL and the normal light continues to flash and if I push the cancel/drain button then it starts a steady flash


... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

The stop/cancel light keeps flashing. I have tried Heated dry to Normal sequence buttons and I have tried Heated dry to High temp wash sequence. When I have pushed soak and scour the stop/cancel light stops and the Pot/pan and Normal wash lights start blinking


Unfortunately I cannot view the comments from other fixya.com consultants so I am coming in cold on this one.\015\012\015\012But it appears you are trying to isolate the problem of why the stop/ cancel light are flashing. I suppose the on ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Maytag mjd 2005 when started on normal gives a once-every-two-seconds "wash". Seems to pump out some water each time. When turned off and on again 'normal' button lights and the same thing happens. Will not start without the normal button lighting.


I have the same problem but now on all cycles - to get it off normal and try the other ones, open the door, hold down the 'normal' button for three seconds, and then at least try the other settings temporarily. ... Maytag 24 in. MDB9750AW Dishwasher

Maytag dishwasher model MDB7609AWW2 has a blinking clean light. I followed the advice on fixya (thankya!) and by alternating the normal and heated wash buttons I was able to return the lights to normal. However, once I tried to run a normal cycle, it didn't do anything other than fill and drain. I then ran the hot water faucet in the sink until hot and tried another new cycle, but no luck. Any advice is MUCH appreciated!


... Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

Whirpool Dishwasher ADP5966 Turned dishwasher on. Only light that comes on is normal wash light. Start button is flashing when normal wash light is on. On pressing start button dishwasher does not work


Most likely the door switch is not making proper contact when you shut the door or the Start button is faulty. Needs someone to look in the door panel to fix. ... Whirlpool Dishwashers

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

**My dishwasher normal light keeps blinking** Hi, my whirlpool dishwasher stop working.all lights are off except the normal light which keeps blinking 24hd a day please help me Phil Thanks


I have the same problem. I have tried turning off the breaker and the door seems to be locking, but still won't work. Any other suggestions? ... Whirlpool GU2400XTP Built-in Dishwasher

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

NORMAL Wash light is blinking and I can't CANCEL wash. GE Quiet Power II PROFILE dishwasher. Started a normal wash and a few minutes into it the NORMAL light started blinking and can't find a way to reset.


We had the same issue with ours...tried turning off at the breaker, still didn't reset. Contacted appliance repair who came in and unplugged it from underneath the sink, waited a few seconds and plugged it back...dishwasher reset and repairman charg ... GE Dishwashers

GE GSD5320 seemed to finish all light wash cycles. Then it began to beep, with the NORMAL light blinking. I hit RESET, but none of the other buttons worked. I threw the circuit breaker for this appliance and waited an hour. I Turned the circuit breaker on but now I get the NORMAL light blinking, even when the door latch is not engaged. No buttons work.


... GE GSD5320DBB Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

My kitchenaid dishwasher model kudpo2frsso built in lights are flashing normal and cancel I shut off the breaker for 20 minutes pressed Normal heat dry X2 Then cancel x2 but to no avail. Any suggestions its the day before Thanksgiving HelpI T The Normal and Cancel lights are flashing simutanuously and the dishwasher is not working at all


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0541 seconds