Having problems with your Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher ?

Our Frigidaire Dishwasher buttons stopped working. If we push normal cycle it will not select as well as other cycles. The last time it happened the maintenance guy came and turned it on and off and it started working again. That didn't work this time. We still can't select some of the wash buttons


Answers :

You will have to replace that selector switch
http://tclaundryrepair.com/
Repair Help & Product Troubleshooting for Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Frigidaire Dishwasher buttons stopped working. If we push normal cycle it will not select as well as other cycles. The last time it happened the maintenance guy came and turned it on and off and it started working again. That didn't work this time. We still can't select some of the wash buttons


You will have to replace that selector switchhttp://tclaundryrepair.com/ ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

"Quick Rinse" light blinks constantly, unable to select "start" unable to select "normal wash" sometimes can select "pots and pans" but still not able to start. Was working normally, when it stopped at end or pre-rinse to start the main washing cycle, the "quick rinse" light came on blinking, and no other button works except as described above. Thanks,


Hi,\015\012 \015\012Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow ... Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


Your touchpad is likely faulty. Sometimes called a control panel. You can get parts, manual, pictures, part numbers, and more at partselect.com or repairclinic.com ... Dishwashers

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


The electronic control board is most likely the issue. I would replace the pab that controls the dishwasher functions. The control board controls the cycles and the wash time selection as well as the on/off function of the dishwasher. ... Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I have a KitchenAid KUD1021RWHO dishwasher that will not turn on when I hit the start button. The LED lights work when I press cycle selection ie. "normal" but when I press the start button nothing happens. I have waited for a couple of hours and then it will start. However during the last week it has happened more frequently and now it has not worked for the last (2) days. Any ideas as to what the problem may be? Thank you for your help!!!


Hello,\015\012\015\012This is a very common issue on these units. The touch pad has failed. You can try to flip the breaker off for several minutes and see if that clears the code. More than likely the touch pad will need to be replaced.\015\01 ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Hi. My electrolux dishwasher (DX403WB*06) won't turn on. It was working fine until this morning. The 'start' button seems stuck in, but the lights don't come on and I can't select


... Dishwashers

The start button light is very dim and the machine will not start, all other buttons and lights seem to be fine. The problem came about gradually some times it would work other time not, now not at all. the machine is about three years old.


... Amana 24 in. ADB1500AW Built-in Dishwasher

My Maytag NDB9601 will not start any cycle. You can select the cycle and the display will show the time, but the start and delay buttons, located on the front, not the top with the cycle buttons, will not activate. This leads to the dishwasher not working at all. It worked in the morning, but not in the evening. Dishwasher is 1 year old.


Sounds like a possible door switch problem. \015\012\015\012If you take that area of the door apart, check the ribbon cable for keypad. You can clean the connector with a pencil eraser. ... Dishwashers

Won't start! Model # KUDI01ILBL4 Only Normal Cycle button lights, but will not start. Had same problem before and was told to press Cancel button to drain water and then turn power off for a while and then back on. Well, this worked a couple of times, but not this time. Need an expert opinion on next move.


Toggle between 'heated dry' and " normal ' until all light illuminate Then press cancel. now ensure door closes properly without striking cabinets slightly. The neutral for most components run through the door switch and jarring actiong causes a faul ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

KitchenAid KUDI10FL dishwasher- The door spring system broke and I repaired it, but now all of the sudden the dishwasher will not start. The door may have been dropped a couple of time before the spring system was repaired, but it did not hit the floor, just a hard sudden stop. All of the cycle setting lights come on when they are pressed except for the start button. Just before the start button stopped working the dishwasher started by itself or started several hours after cycle selection had b


Hi- It is possible that the door latch is not completely engaging. If the door dropped the hinges may have bent a little thus preventing a good contact with door switch. Try pressing and holding the door shut, hard, and pressing start. If that wor ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Maytag Quiet Series 800 dishwasher won't start. The only button that I can get to work is pressing and holding the locking feature--that light eventually comes on. A couple of times I came back in an hour or so or the next morning and hit the start button and it started right up. Now it won't start at all. VERY FRUSTRATING!


... Maytag 24 in. MDB6100A Built-in Dishwasher

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace. ... Dishwashers

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Dishwasher does not start, on any cycle selection. the only button that works is the cancel button which tells me the unit has power. this has happened before and a service tech was called and it "magically" started after he pushed the cancel button, not so this time??


Make sure the floor is dry where you are standing. \015\012 \015\012Push the cancel button twice in quick succession to attempt to turn the washer off.\015\012 \015\012Open the door all the way and look over t ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Hobart lx18h Our commercial Hobart dishwaser stops working after running a few cycles. After pressing start the LED display will continually blink and nothing will happen. We'll turn it off and on again a few times to reset it and it will start up again eventually. We've had an appliance guy look at it multiple times. He's replaced a part or two for it but the problem continues and he isn't much help. Anyone else had any similar issues with this model of dishwasher?


... Dishwashers

Our ESD310 has a message of OP on the screen. It will come on and run on its own if the door is shut, counting down from 2. When I can get it to turn on and start a cycle it runs a bit, skips a bunch of time, runs a little more, and then skips time again counting down from 2. The high temp wash button will light up on it's own while running. The cancel button does not work. It acts as if it has a short, makes funny noises, and I'm afraid it's going to catch on fire.


... Haier ESD310 24 in. Dishwasher

I have a fridgidair dishwasher model FDB4315LFBO and none of the buttons are working this is the second time this happened and last time i removed the cap for the rinse aid and heard a rush of air then everything started working. I already turned off the power to reset things and the PF light flashed until i opened the door then it went back to everything being dead.


Sounds like something has burnt in the main powerboard. ... Dishwashers

On my whirlpool ADP962 dishwasher the start light is flashing but nothing is working. I can change the programme type (ie rinse, wash etc) but the programme will not start. I can't select either half load or a time delay. By holding the start button it will start the pump but when this stops it goes back to a flashing start light. The programme progress lights are not lit. What is this telling me and how can I reset it?


... Whirlpool Dishwashers

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1282 seconds