Having problems with your Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher ?

My Frigidaire 4000 Dishwasher panel board is lighting up with almost all lights on/flashing. When the door is closed the pump engages and ther is no water in the machine. If we put water in it drains successfully. The following is flashing on the control panel: washing, drying ER, clean and s. Up top lighted up is china crystal and rinse only. What is going on?


Answers :

Repair Help & Product Troubleshooting for Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Frigidaire 4000 Dishwasher panel board is lighting up with almost all lights on/flashing. When the door is closed the pump engages and ther is no water in the machine. If we put water in it drains successfully. The following is flashing on the control panel: washing, drying ER, clean and s. Up top lighted up is china crystal and rinse only. What is going on?


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Model #PLD4555RFC0 The control panel lights on the front are all flashing and start cancel button will not change anything. flashing Er with wash, dry, clean, and and S showing. Top controls have China/Crystal light flashing and Low rinse agent light flashing. Nothing seems to work


... Frigidaire Dishwashers

I have the Whirlpool Quiet Partner 1 the wash cycle starts and about 20 Min.'s into it the clean light starts flashing or the the start light, one or the other each time and it wont dry the dish's anymore we have already replaced the panel once and it has always popped when it is filling with water or changing cycles. HELP!!!! I hate washing dish's and I am beginning to hate all Whirlpool Appliances.


If the clean light blinks 7 times thats you heating circuit. Test the heater with an ohm meeting to see if it has open. If so order the heater kit and it comes with the control board. ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

GE dishwasher Model GLD4560n00ss Control panel won't change when buttons are pushed. Two lights keep flashing-Normal Wash and Heated Dry Beeps once a minute Water won't fill


... GE Dishwashers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

First 2 weeks ago i put an electric control module into the upper section. what comes on is the green flashing light for clean. in checking connections i found the paper for trouble shouting. i did what they said to do. they said hit the time saver - high temp - time saver - high temp. from there all the lights went on & the wash cycle started and ran. then it just stopped & the green light for clean just flashes. the water is still in the bottom & won't drain.


The error indicates that the machine has taken too long to drain the water. Do the following.\015\012 \015\012\015\012Switch off the machine, unplug or disconnect the ma ... Kenmore 16874 Built-in Dishwasher

I have a GE dishwasher with front control panel and at first the wash and dry lights stayed on and it was beeping every 30 sec. when I turned the breaker off for the required 30 sec. the lights started flashing and it is still beeping. The control panel seems to be frozen as it is not working and wont do anything.. everything was working fine before this. I bought it at Home Depot on 3/14/07 and had it installed by a licened electricion. Help


Call ge @ 800-386-1215 for service ... Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

The clean light in main panel and light wash plus heated dry lights are all flashing and machine won't start. it is a model mdb7100awb


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. If the\015\012clean light flashes 7 times, pauses, and then repeats. When the dishwasher\015\012doesn't sense a water temperature increase, it stops working a ... Maytag MDB7100AWB Dishwasher

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

My DW60 Hotpoint stopped in the middle of wash. all panel lights flashing at the top left. water colected at the base. tried to restart with a fresh cycle. program selection successful. drained all the water. loaded fresh water. but giving grumpy noice and not the usual thrust start.


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

New dishwasher (Beko 2542F slimline model). Put it on for 1st time last night -when I got up this morning, the cycle which should have taken just over 2 hours hadn't finished. There's soapy water in the bottom of the machine which hasn't drained and the "wash" light is still on. Looks like the dishes are clean but hasn't moved onto the rinse/dry part. Followed instruction in manual to drain it (hold start stop button till lights flash and should drain in 45 sec) but nothing happened.


... Beko Dishwashers

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers

Zug adora 12s. d panel flashing lights, wont wash, standing water


... GE Adora GHDA654LBG Dishwasher

FDB834RFS0 FRIGIDEAIRE DISHWASHING M# FDB834RFS0 Precision Wash System.... All control panel blinking.... Main power turn of and repower then ONLY HI TEMP WASH and NO HEAT DRY LIGHT ON. How do I enter control panel mode to clear blinking lights? Could it be faulty element inside dishwasher? Any suggestions gladly appreciated. Tks .. AA


... Frigidaire Dishwashers

Kenmore dishwasher model number 655 16022400 has a flashing green clean light. Reset panel and now the washer will not complete a wash cycle. The washer stops at the drying part of the cycle. What is the problem?


... Kenmore Dishwashers

Hello expert, We are having a new kitchen floor laid and the contractor moved the Whirlpool dishwasher out to lay the floor under. Since it was replaced into it's normal under the counter spot, green "clean" light flashing in succession with a brief stop then starts again. Not really bothered as long as it worked, but of course it doesn't work - What do you suggest?? P.S. Had a problem app. 2 years ago when someone backed into the control panel, also ceased working and repairman charged ex


Someone grabbed the control panel and knocked it around or flexed it whist moving it in and out of your counter.\015\012\015\012Either the PCB board behind the little buttons flexed and cracked, or the ribbon cable that connects the PCB b ... Dishwashers

Model 66516032402 Ultra Wash quiet guard. Clean light on the control panel is flashing. Manual only says to call for service. What else can I learn and is there something that I can replace to fix it and avoid unneeded service fees


Hi there,\015\012 \015\012This is a common problem in Kenmore dishwashers and is often due to an issue with the temperature sensor. It's not necessarily a fault that requires a service call or any replacement parts. Of ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2378 seconds