Having problems with your Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher ?

I have a Frigidaire GLD 3450 RDB0 dishwasher that begins the wash cycle then halts midway and shows 'ER' on the display. I replaced the computer board with no better results? Any suggestions.It is only 4 yrs old. Thank you,


Answers :

Repair Help & Product Troubleshooting for Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Frigidaire GLD 3450 RDB0 dishwasher that begins the wash cycle then halts midway and shows 'ER' on the display. I replaced the computer board with no better results? Any suggestions.It is only 4 yrs old. Thank you,


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Hi, We have a small CDI454-80 Candy Dishwasher. It is just 18 months old and has only been used around twenty to thirty times. It has recently started to leave a film on all the dishes after the wash is complete. We noticed it a few days ago and have tried different tablets but with no better results. We have also noticed that the cutlery is getting brown rust like marks on everything in the silver tray. PLEASE HELP! Thanks, Dave


The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your d ... Candy A8001 Dishwasher

We have a n eight year old fully integrated asko dishwasher. Only the rinse cycle works, so I rinse many times - last rinse with detergent and then run the short program which does not wash, but will dry the dishes. The circuit board was replaced once before under warranty($500.00 labour) and I suspect that we may have to do the same again. Can we find this on the internet and do it ourselves; we have good electrical knowledge. Thank you in advance.


This is most likely an issue with the timer. Timers\015\012don't often fail. But if every other part of the dishwasher seems to be\015\012working properly and the timer knob seems to be stuck in one\015\012place--doing one function continuously--the ... Asko Dishwashers

In December 2010, I purchased an Electrolux range, microwave and dishwaser for my kitchen. Already I have had to replace the computer boards on my all three appliances. Last night, I load the dishwasher and go to turn on and the computer board is dead again. What is the problem and would you advise that I return all 3 appliances for a refund?


... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

Model # KUDSO1DLSS1 Kitchenais dishwasher - had a burnt electric smell coming from the area of the touch pad (not the vent). Did "some" research and decided to replace the control board - smell went away - ran 3-4 cycles over a few days and then - no lights - tried a new control board (thinking the old defective) - nothing - replaced the thermal fuse - nothing - what next????


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Normal cycle light blinking, won't turn on MDB7609AWW1. Was told it was micro computer. Replaced it....same problem..Put old micro computer back in.. wife secured all wires and banged the machine and it started working tfor a few Days.. stopped with same old symptoms..I'm sure guru is correct and it is the touchpad, but his facing appears to be glued on,I don't wan't to ruin the front of the console , and I've not been able to find a touchpad part on the schematic or online. Help???


... Maytag MDB7609AW Builtin Dishwasher

The unit fills up with water but the circulation pump wont turn on. if i jump the pump it works. the pump is connected to the timer board. is there any sensor that would cuase the timer board not to turn on the circulation pump. this unit seems to be manufactured by ASKO mod. DW20.3 i dont want to replace the board ($375.00) if not nessary. thank you


Hi\015\012\015\012\015\012Thanks for using FixYa. There is no sensor on your dishwasher for drainage purpose however, it uses a drain solenoid to open and close the dishwasher drain port. If this \015\012solenoid ... Dishwashers

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

I am trying to replace the GUIDE RAIL BRACKET ASM on my GE dishwasher (model no. GSM1800JWW). How do I either: (a) remove the old brackets, and then install the new ones; or (b) remove the rollers from my new brackets, so that I could slip these rollers onto the old brackets still in the dishwasher, saving the trouble of removing the old brackets in the first place? Either solution would be acceptable, but right now I can't figure out how to do either one without breaking something. Thank you v


Be ready for both . because if they break you can still replace it. but (a) is to me the better choice. let me know how you made out and send me a 4 thumbs post if it works out ... Dishwashers

MAYTAG MDB7600AWQ DIAGNOSTIC CHECK USING CONTROL BOARD AUTO AND MANUAL, ARE GIVING ME A HIGH CURRENT WASH MOTOR DIAGNOSIS.(NORMAL WASH FLASHING) THE BOARD ITSELF CHECKS OUT OK. ALL FUNCTIONS WORK AS THEY SHOULD.WASHER FILLS THEN ATTEMPTS TO RUN FOR (ABOUT 3 SECONDS) IT WILL DO THIS 3 TIMES THEN BOARD GOES BLANK. ALSO, THE WASHER WILL FILL WITH THE DOOR OPEN??? BUT WON'T ATTEMPT TO WASH. REPLACE WASH MOTOR?? THANKS lYNN


I would agree.. Here is a site for you to copy and paste in your address bar that I think will be helpful:http://home.howstuffworks.com/how-to-repair-a-washing-machine.htm/printable ... Maytag Dishwashers

Kenmore 665.13823 dishwasher couldn't stop a washing cycle. It was identified as "control board" issue. Is it possible to fix the circuit board/timer insted of replacing the board? Also, where are the mayjor screws located to open the housing for the control board? Thanks


Hi,Unfortunately there is no way to repair circuit board or timer. The procedure to replace control panel is :-Step 1 Disconnect the power supply to the dishwasher by turning off the circuit breaker. The circuit br ... Dishwashers

I have the above dishwasher shv57c03uc just less than 5 years old. The door latch does not engage solidly. when i pust start button left side lights on indicator right does not come on and i have to push on button twice for washer to come on. When it does come on the cycle is real short and it does not complete a full cycle. I an asuming the circuit board is defective!! does this sound right? if so how can i replace the board?where can i get troubleshoooting instructions?


Hi\015\012\015\012You are right it is the ... Bosch 24 in. SHV57C03UC Built-in Dishwasher

'Dead' DU1100XTP The dishwasher will not start - no lights at all - no indication that anything's working (although I confirmed the unit has power). I've seen numerous posts regarding the control board - is there a problem with these in general? My unit is just beyond the warranty (naturally!) so I'd like to know if there's been any concession made by the manufacturer due to the number of problems. I'd gladly replace the board if Whirlpool would send me one. Thanks.


This may sound simple but... make sure its plugged in all the way. ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Judging from the information on this forum and others, we think we need to replace the control module on our Bosch dishwasher (she45m05uc/50). The general consensus seems to be that the module has an underrated relay and will burn out again. Has the board been redesigned? Is there a newer board that would work in our model? Bosch says that only part number 676962 will work. Thanks for your help, Deb


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

Maytag dishwasher, has dead control consul, does have power to the board and the latch swithes are good. is there a way to troubleshoot the touch pad? replace the console or the board, or both? thanks, Bruce


The only way possible to see if the touch pads are working is to test the voltage of the control pads when it contacts. The input of the Microprocessor should be checked for the pad control inpulse to come in. If there is no trigger voltage to the mP ... Maytag Dishwashers

I have a Kenmore undercounter dishwasher..model 665.16022400. The "normal wash" light keeps blinking..nothing will work on it..I tried reseting didn't work, killed the breaker for a while, didn't work. I tool the panel off and reseated the ribbon connection to the electronic board..didn't work. I'm not sure if I should be replacing the electronic board, or the control panel that contains the buttons. None of the buttons appear to be stuck. thanks - Andrew


Hi,This is a common problem. As i cannot diagnose the machine myself, it would be tough to exactly comment on the fault. However, more often it is an issue with control panel keypad assembly.You need to replace that.Let me kno ... Kenmore 16024 Built-in Dishwasher

Maytag dishwasher, control panel is dead, has power to board,but there are no lights on the panel when you close the door, like it normally would. any ideas I replaced the board with no succes. thanks Bruce, B&L Appliance


I think you have diag your problem . your have power to the board . so the inter lock switches are ok . and no lights . if you look at the printed pc board i think yoy may be able to see that one or more ... Maytag MDB5100A Dishwasher

Hey guys, I am a dishwasher repair guy in barbados, the caribbean. I am having problems with a Hobart LX30H. the relay board is doing half the things right and the othrs not at all. I replaced it with a new one and the same results. At startup, the wash sump heater and wash motor are running, but the fill valve, drain valve and rinse booster are not running. Hence the startup operation is stalled. the funny thing is that the rinse booster and fill valve led's on the relay board light up at


Not sure what sort of problems (fault codes etc) you were having before you chose to go on the path of replacing the relay board.\015\012\015\012It might help to know what fault codes you have been noticing.\015\012\015\012One ... Dishwashers

We have a 100% failure rate on multiple parts on two Maytag dishwasher units and no longer can get replacement parts from anyone. Any ideas of what to do? Here is the latest summary we sent to Maytag: Thank you for the help last fall. As a follow-up, we are still having very bad results with your product. You authorized replacement of the unit which was done. After one dishwashing, THE NEW UNIT SHOWED THE SAME PROBLEM (WOULD NOT TURN ON). I called in and you referred us to a senior te


Well iam sorry to here of you major problems.if the control board has been replaced several times and no luck fixing it there may be a problem with the main power supplied to the unit,as well as having a problem with the wiring harness.usually a manu ... Maytag 24 in. MDBH940AW Built-in Dishwasher

I have a Whirlpool DU1055XTSS dishwasher that completely stopped working. I took it apart, found the thermal fuse to be bad, ordered a new, then replaced it and it worked for 2 loads. Now the thermal is open again. What could be "taking it out"? Is the thermal fuse strictly a thermal or does it repsond to current? It's 2 years old, i have already replaced the heating element, the main control board, and now the thermal....twice.


Hi.If the thermal fuse is blowing, that means that there is overheating.Common causes for overheating are:Thermostat cutting off too late.Plugged element.Plugged element means that the element sta ... Whirlpool Dishwashers

Hi I have a whirlpool diswasher which is about 7 uears old which has blown the fuse (and the mains trip) half way through a cycle. Replaceing the fuse has resulted not resulted in the restoring of power to the unit. Is there anything simple I could check (in line fuses etc.)? Cheers


Some whirlpool models do have a thermal fuse in the consloe mounted to the main control board housing, might looke to see if it has one and if it is good ... Dishwashers

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

SHU 5316 UC dishwasher by bosch. I think it is from about 1998 or 99. It blew a circuit breaker yesterday. I reset the circuit braker, but it won't even power on. It may have burned something out. We replaced the control board 2 years ago. Please tell us: 1. Is it worth fixing again, or just replace? 2. Any suggestios? Maybe the pump has shorted? THANKS SO MUCH!! Mark


Hi Mark -There's no internal fuse in this dishwasher, so if there's no power you may well be looking at a new control unit and probably another major component as well, depending on what caused the overload or short. The most likely ... Bosch SHU5316UC Dishwasher

Hello! I just ordered a new facia panel for our Bosch dishwasher SHU9955UC/U12. It seems like it should be fairly easy to replace it (meaning, myself...). Is it really just a question of unscrewing the screws on the inside of the door, removing the old panel and then replacing the new one? Are there any especially delicate inside mechanisms/parts That should be protected? Many thanks.


... Bosch SHU9955UC Built-in Dishwasher

We are on the mainland but our dishwasher is on the island of Maui. We are told that the main control board is out. The dishwasher is only about 4 years old and is used only about 4 months out of the year. Is this a commmon problem with Bosch dishwashers? Is there only one "Main" control board? If so, do you know what the part number is? thank you.


... Bosch Evolution 800 SHE58C02UC 24 in. Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1234 seconds