Having problems with your Frigidaire 24 in. FDB510LC Free-standing Dishwasher ?

My dishwasher is a Fridigdaire FDB510LCS1, approximately five years old. The timer/knob stops advancing at about 7 o'clock, somewhere in the wash cycle. But the washer keeps running. I marked the place where it stops and, on additional tests, it stops in exactly the same place. I can advance the knob slightly past this location and the washer continues through to the end of the cycle.


Answers :

Hi
\015\012
\015\012This is due to a faulty timer on your dishwasher. You would need to replace it to resolve this issue. You can buy the timer for your dishwasher from this link---
\015\012
\015\012Frigidaire 24 in. FDB510LC Free-standing Dishwasher Parts
\015\012
\015\012
\015\012daniel_s_20.gif
\015\012
\015\012Part# F3 is timer.
\015\012To disassembe the Timer please follow this procedure--
1. Disconnect power to the dishwasher
2. Remove outer door panel
3. Remove knob from timer by pulling straight off timer shaft
4. Remove console
5. Press in on locks for the disconnect block and pull block from timer.
6. Remove two timer mounting screws. Ground wire has a locking terminal press down on lock to remove terminal.
\015\012Hope this helps... Please post back if you need more information.
\015\012Daniel
Repair Help & Product Troubleshooting for Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher is a Fridigdaire FDB510LCS1, approximately five years old. The timer/knob stops advancing at about 7 o'clock, somewhere in the wash cycle. But the washer keeps running. I marked the place where it stops and, on additional tests, it stops in exactly the same place. I can advance the knob slightly past this location and the washer continues through to the end of the cycle.


Hi\015\012\015\012This is due to a faulty timer on your dishwasher. You would need to replace it to resolve this issue. You can buy the timer for your dishwasher from this link---\015\012\015\012 ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

We have a hotpoint aqaurius dishwasher df23n. When put on wash 4, the timer stops half way through and has to be helped. When the programme then continues through the rinse cycle, it stops half way through. I have tested the water heater and thermostat electrically and they seem ok. Is there anyting else that stops the timer at these positions? The timer knob is free to turn and is not jamming? Steve B


... Hotpoint Dishwashers

Hi i dont know the model of the dishwasher.. but the controls are fairly staright forward... a little knob for temperatur control and an on/off button.. and a light that lights up green when dishwasher is switched on... now the problem is as happened recently, when you switch the washer on greenlight is on and washer can be heard doing something but after a minuit or so the washer stops and the green light flashes. open up the dishwasher no sign of water or that it has done anything at all... th


It sounds like your washer is not getting enough water to start. If your washing machine is filling too slowly or not at all, then you probably have a clogged screen on the back of your washer. To check this: \015\012\015\012 ... Whirlpool Dishwashers

Zanussi DA6141. Dishwasher will not progress from turning on at wash code c1. Test 1: No kinked hoses Test 2: Put water in by hand and it empties it. Lift out the central sieve/filter and it all appears very clean. Test 3:Inlet water filter clean. No actions except low buzz (?solenoid?) after emptying. (Possible Hint: Previously this washer sometimes stalled with knob rotated 15 degrees clockwise from C1 position and would continue to wash dishes indefinitely, if unattended. This was


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the\015\012cycle doesn't complete, check these:\015\012\ ... Zanussi Dishwashers

I have a excell 2500 psi max honda 5.5 ho vr2522 2.2 gpm presser washer and has been stored for about a year, still looks brand new and has only been used twice before, it has oil and was stored with no gas in the tank, i put fresh gas in the tank and blead the fuel bowl until fuel ran out like it should, the washer wont start, ive checked the turn on switch as well and the fuel cut off knob, i spayed gas in the carb and it fired up but stopped running as fast as it began to run, its not getting


... Honda Black Max 2600 PSI Pressure Washer

I was using my Karcher 350M pressure washer working fine but it just stopped having tripped the power boards circuit breaker. The breaker now trips each time I switch on the washer. There is no smell of burnt motor and the electric did not get wet when last in use. Appreciate any suggestions or tests that can be made. I have a decent multimeter. Thanks.


... Karcher 1750 Psi Elec Pressure Washer

Just stopped. I have an Amanna dish washer that is only 2 years old and it just stopped. It has about an inch of water in the bottom. I have power to the unit. No buttons show any lights or reaction when pressed. How do I test the latch buttons?There are 4 wires leading to the latch assembly, can I jump them to see if the latch is the problem?


Should be able to but it will run withdoor open if you do that so be careful. Have you tried holding in on the door and see if it will work? ... Dishwashers

I have kelvinator dish washer in Bahrain. The sale agent J.A Zayani suddenly stopped its sale and workshop. The dish washer produces a high blasting sound while running though perform its cycle correctly. We are scared to use it. No one in Bahrain accept its repair as the agent has abodoned its operation. Did you fix anothe ragebt in Bahrain. Please advise what is this bang sound appearing once or twice during operation. Is it safe to run it. How to reapir it. Thanks in advance for your assist


... Kelvinator Dishwashers

I have a Bosch 2046 UC DW. When you try to start the cycle you hear the timer clicking. The knob slowly rotates to where it should start the cycle but stops there and won't start the operation. If yiou advance the knob it opens the soap dispencwer but the pump or cycle will not begin gerald qually


The programmer is faulty, effectively worn out, and needs to be replaced. You may be able to service the mechanical parts of the programmer by cleaning and lubricating it and possibly by replacing the springs but it's just easier and less time consu ... Dishwashers

I OWN A COLEMAN 1500 POWERMATE POWER WASHER. AND NEED TO PURCHASE EITHER AN EXTENSION OR A NEW HOSE AND WAND COMBO OF 50 FEET. THE REASON BEING THAT I AM HAVING DIFFICULTY WASHING THE UPPER PARTS OF MY 3 LEVEL HOME. THE HOSE ATTACHMENT IS A TWIST/TYPE AND THE WAND/HOSE IS ALL IN ONE. CAN ANYBODY GIVE ME A RESONABLE AND ECONOMICAL SOLUTION. ALSO WOULD THE ADDITIONAL HOSE HAVE ANY NEGATIVE IMPACT ON THE WASHER AND ITS CAPABILITIES? THANK YOU IN ADVANCE


Here are a couple of links to the stuff you need:\015\012\015\012link 1\015\012\015\012 ... Pressure Washers

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

Stopped mid cycle with dirty water left on the bottom. cleaned filter and it worked fine, twice. This time it stopped and i can't get the power on. just moved in, with existing washer and have no manual. thanks in advance.


Hi,Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Bosch SHU5316UC Dishwasher

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

Our craftsmen electric pressure washer stopped working while in use. We have power - red light on gfci and we tested the master switch - has power too. So what can be the problem? One post mentioned a jammed pump switch. What is that and where is it? We used it 2 weeks ago and it worked fine.


The pump switch they spoke of is an internal switch. It is activated by a valve so that when you let go of the trigger, the machine shuts off. This valve is stuck or the switch is bad. Usually the valve is the problem. I would go to Sears and get ... Pressure Washers

GE Mod # GSD22360Z04WW will not drain water. I manually pushed the solenoid down and the pump and motor seemed to run. No water pumped out of the hose that was disconnected from the garbage disposer. I have discovered that the plug for the disposer was not taken out where the dishwasher hose attached. The dish washer stopped working after a new disposer was installed. I rotated the control knob and at no time did the solenoid for the pump operate. It went back to normal position after control kn


... Dishwashers

Frigidaire dw m# fdr252rbb1 stalls in the middle of the light wash cycle and just keeps washing and won't advance. I replaced the timer and it does the same exact thing even without the knob attached


... Frigidaire Dishwashers

Replace timer maytag la710 - Maytag Washer Timer 205637 2-05637 W/ Knob Assembly Tested & Works


... Maytag Washer Timer 205637 2-05637 W/ Knob Assembly Tested & Works

We have a +11 year old Bosch SHU3006/UC/U06 that never leaves the wash cycle. We had to stop it during our last test run at 3 hours. Chat advise is suggesting a water temperature problem (I origionall thought the timer), suggesting that the cycle will not advance until it hits a set temperature (170 degrees). We checked and noticed that the water in the machine was only around 90 degrees during a wash cycle. We do not have exploded views or parts drawings, nor electrical schematics. I wou


Check continuity of the heating element to see if it is broken/open.\015\012\015\012The dishwasher prefers that the incoming water (water heater) be 120 degrees (F) ... Bosch SHU3036UC Dishwasher

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Calypso washer display "FD" perhaps meand full drain and can't reset and just stop. I run washer with back cover out to see that while water doesn't fill up the drum but normally agitates and just fill up the water reservoir to full and don't drain out to sewer and washer just stops with the message "FD"


Peace broohilda,ngafm At your service!With an error code the only way to find and to repair this is,First unplug the washer and wait a few minutes then restart it like rebooting your computer when its acting strange! ... Dishwashers

Model number 66515632000 Kenmore Ultra wash with quite guard about 8 years old Washer stopped near end of rinse cylce, dishes look clean, water in washer did not drain and looks clean. All attempts to restart washer, or hit drain etc result in attempt to start and then it stops. sounds like trying to start a car with a very weak battery.


Unfortunately it sounds like you have one of two possibilities. A) You have something like a piece of glass or food ect. that has worked its way down into your pump and is tying up the impeller or pump as its trying to start. -To op ... Dishwashers

Washer won't advance from cycle to cycle


When the cycle doesn't advance, it's probably the timer or a cold-water supply problem: * It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin ... Danby DDW1805W Designer Series Free-Standing Dishwasher

I have a Frigidaire dishwasher, Model FDB15000LFCO. Serial No. TH74135326 purchased 10-19-07 from Lowes. The washer stopped working almost immediately. On December 5, 2007 the computer brain for the washer was replaced by Able Appliance Service, LLC, Swannanoa, NC (828) 296-1017. Four months ago my electric bill for three months was almost twice my average use for the time period. We stopped using the dishwasher for one month, and the bill returned to normal. Was one part in the dishwasher in


I think you have one 0 too many in the model no. should have been FDB1500LFCO. The user manual is available here.\015\012 ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0814 seconds