Having problems with your Frigidaire 24 in. FDB635RF Built-in Dishwasher ?

Lights on but wash

\015 My dishwasher wont wash.the lights are on but nothing happens\015

Answers :

I assume you can't even hear water running. If that's the case, you may have a faulty or stuck water solenoid valve. Under your sink, there is a water line that connects directly to your dishwasher. That line is always on, so it's always under pressure, unless you turn off that valve under the sink. Therefore, something has to prevent water from flowing into the dishwasher, and that something is typically a solenoid valve. The solenoid typically gets it's power when you start your dishwasher. If the solenoid is stuck (most typical problem) a little gentle persuasion from the handle of a screwdriver may be all you need to unstick it.
Repair Help & Product Troubleshooting for Frigidaire 24 in. FDB635RF Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

The three lights for Pots & Pans, Normal Wash, Econo Wash are all flashing. When I hold the start button down for four seconds, just the Normal light is on. However, once I close the door, all three lights are on again, and the dishwasher does not start. We have tried unpugging it and then plugging it in again. It worked once then went back to all three light flashing. Before this, only the Normal Wash and Econo Wash lights were flashing.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I can't seem to access any previous post dialog that may have taken place but I'd like to help if you can fill me in on whats taken place to this point.\015\012\015\012The scenario you describe i ... Viking DFB450 Dishwasher

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

Global 450 dishlex dishwasher. Had the handle replaced 2 months ago. After that the ready light did not switch off as before. Now it only rinses. When you set the normal wash cycle the lights for Pre Wash, Wash and Rinse all come on. Pots cycle, the Pre Wash, Wash, Rinse and Dry all light up together, hence the machine thinks it up to that stage of the cycle. Can this be repaired or not. The machine is approx. 12 -14 years old.


... Electrolux Dishwashers

I have a Kenmore Quiet Guard Ultra Wash and the lights on control panel are blinking green. It's the Smart Wash, Normal Wash and Light Wash lights that are blinking green. Dishwasher won't sta


... Dishwashers

Our whirlpool dishwasher will only go on the light wash, just or a short time and then shut off. the other cycles, heavy and pots and pans will not go on at all. when we press the light wash button, both the light wash and rince and drain light all go on, for just a short time, then shut off. help!!


The membrane or touch pad is bad. Most of the time you need to replace the whole control panel. Usually one of the buttons has failed causing this symptom. ... Dishwashers

My dishwasher won't start (Series 300 purchased 14 months ago). The following lights are on: light wash,hi temp wash,sanitize, locked and the start /resume light is flashing put goes out when pushed and the machine does not start when closed. there has been an on going problem with the regular wash light not coming on when pushed.


Hi\015\012\015\012It may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting t ... Maytag 24 in. MDB9750AW Dishwasher

I have a Bosch SHE6AP05UC dishwasher. All of a sudden when I turned it on to wash a load the clean light and the quick wash light came on and when you push the wash button nothing happens. When you turn it off and on those 2 lights come on solid and you can't wash. How can I reset or what can I do to troubleshoot this?


... Bosch SHE6AP05UC 24 in Builtin Dishwasher

I have a maytag dishwasher and the light wash light stays on even after a wash cycle. Tried to press normal wash and goes back to light wash. What could be wrong?


I have had numerous problems with the conyrol panel on this particular unit. Runs about $95 ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

Kenmore Ultra Wash Model 665.1388 problem the normal wash green light is on heated dry light is on and the start resume light is flashing but wont startup helpppp


See your instruction manual and go to the section troubleshooting and fix it.if you do not have the i.manual download for free www.retrevo.com or www.fitness.manualsonline.comsee the diagramGod bless you ... Kenmore Dishwashers

Kenmore Ultra Wash Model 665.1388 problem the normal wash green light is on heated dry light is on and the start resume light is flashing but wont startup helpppp


... Kenmore Dishwashers

Currently the only setting that is working is Sani Wash. If I use any of the other settings the Intake Drain light comes on and everythig stops. How can the Sani Wash cycle work fine and no Intake Drain light when all other cycles trigger the Intake Drain light and won't continue to wash? Thanks,Karen


I decided I'd wait for the repairman; I don't want to have to pay additional money. ... Dishwashers

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

Dishwasher DU1100. Odd behaviour during cycle: "Washing" light goes off and sound of washing stops. "Normal" light starts blinking and "soak and scour" light comes on (it was off before). No sound from washer. This persists for at least 10 hours. After that, the lights go off. Is this normal behaviour? It would appear tha the drying cycle did not go.


No it is not normal. It appears that either the membrane switch pad has failed or the control board has failed. ... Whirlpool Dishwashers

Maytag MDB5601AWS Dishwasher worked fine when I moved into my new home less than 2 weeks ago. It just stopped working a few nights ago and the sellers did not leave info on the dishwasher. The only buttons that light up are the buttons on the right side of the START/CANCEL button (which does not light up at all) and the LIGHT WASH button on the left side of the panel. The DELAY WASH button blinks for a while, and then all lights on the panel go off completely. No noise at all comes from the


CLICK HERE for your owners manual.\015\012\015\012If, after reading through it, You feel you h ... Dishwashers

Whirlpool GU2300 Dishwasher. The machine stops for long periods during the cycle. All lights go out. If the machine is opened before the cycle finishes, it will not resume. If I try to restart, the normal wash light begins flashing. If I then try to cancel, the canel light and the normal wash light flash.


I have reviewed your problem with the Whirlpool GU2300 Dishwasher and have the fallowing suggestions for you.\015\012First, unplug the power to the unit and let it sit for a few minutes. This will clear all internal error messages ... Dishwashers

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


... Whirlpool Dishwashers

I lost the manual for my dishwasher. I have two questions: (1) How does Light Wash differ in its cycle from Normal Wash? It seems it should be (but isn't) shorter. (2) When using the Light Wash cycle, should I put soap only in 1 of the cups for dispensing (leaving the pre-wash cup empty)?


\015\012We need the Model Number off the inside of the door to get you the manual please post this first so we can Help you Thanks ... Dishwashers

Kenmore Ultra Wash model #665.1374* purchased 1/26/08 electronic control pad doesn't work properly - one wash cycle works (no matter which cycle is selected, it defaults to same one - light wash) - "washing" and "drying" cycle lights don't work -


... Kenmore Dishwashers

Dishwasher lights up when Normal Wash is pushed, also heat dry - but when start is pushed all three lights (Normal wash, heat dry and washing) blink then go out and nothing happens. This occurred after a 2 hour delay was attempted last night and no washing ever happened.


What is the make and model so we can better assist you? In the mean time shut power off to the unit briefly, then turn it back on and try a normal cycle. Will be watching for a make and model here. ... Dishwashers

Cannot select any wash cycle but quick wash. No other wash cycles will light up when selected. If you select the start button, the quick wash lights and the dishwasher starts (even with door open).


I had this same problem and being an electrical engineer, I decided to see what I could fix before replacing the board. The symptoms were the only cycle I could run was the QUICK WASH - no other cycle buttons responded.\015\012\015\012I took t ... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

My dishwasher will not start just these three lights are flashing at the same time. What should I do? The three lights that are flashing are smart wash , normal wash and cancel drain. The dish washer


Try turning breaker panel for that off, and back on. might just need to be reset. If that doesn't work, call the repair man ... Dishwashers

Kenmore 13742k603 wash cycle lights come on but wash will not light and start


See the diagram attached:1) test the switch door for defective or open, if there are wrong the relais will not close and NOT start the motor.2) Timer test, 3) c.breaker from you home or blown fuse 4) wires defective loose, burn, or break ... Kenmore 13742 / 13744 / 13749 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1104 seconds