Having problems with your Frigidaire 24 in. FDB636GF Built-in Dishwasher ?

Inlet valve water doesn't enter frigidaire dishwasher. I get 12 volts at inlet valve. What voltage is required to operate the inlet valve?


Answers :

Repair Help & Product Troubleshooting for Frigidaire 24 in. FDB636GF Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Inlet valve water doesn't enter frigidaire dishwasher. I get 12 volts at inlet valve. What voltage is required to operate the inlet valve?


... Frigidaire 24 in. FDB636GF Built-in Dishwasher

Model # gsd3320c04bb. I am getting water to the inlet valve. I tried changing the inlet valve but still no water goes thru it. I am getting 22 V AC at the connector when operating. The only water that is circulating in the dishwasher is the water that is remaining in the pump system. Any ideas as to what is preventing the inlet valve from operating?


Sounds like you need to replace the mixing valve which is where your incoming water lines connect to the back of the washer. ... GE 24 in. GSD3320 Built-in Dishwasher

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

Maytag MDB 4000 AWB. Not cleaning. not getting water now. pressure was low when i was getting water. . Soap dispenser would not open as well. I replaced the motor on the soap door. cleaned the float switch. Tested continuity and cleaned out water inlet valve. Still not getting any water


... Maytag Dishwashers

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

I posted a question about my Maytag Dishwashere MDBH945AWW not starting, all lights function, and got a response from you seen here in this thread http://www.fixya.com/ThreadView.aspx?thid=6123266&prdid=519913 I was checking the water inlet valve for a clog and have determined with a meter that there is only 25 volts going to the water inlet valve. I notice a blue wire goes to the float switch which I already checked, there are 2 black wires one of which runs towards the back and cant see where


Hi,No, the lights can be working and a relay on the board can still be bad. These things can be very difficult even for a pro to trouble shoot as there can be many things that possibly can cause a unit not to start.From what you are sayin ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

No water Thanks for the try, but I have already replaced the inlet valve. Still no water. I also checked and confirmed that I am not getting 120v to the inlet valve and/or float switch.


Check your heat dry options I have seen them short out a lot and that will prevent the water valve from getting 120v. ... Frigidaire 24 in. FDB126RB Built-in Dishwasher

I have a Neff Dishwasher and I think the problem is due to the cold water inlet valve. When the dishwasher starts it drains any water and then should stat to fill. If I monitor the voltage to the valve it does switch to 240V but still fails to fill. I have verified that the cold supply works OK and the filter on the inlet is clean. The dishwasher is a NEFF GB5121 and is about 20 Years old.


... Dishwashers

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

I have a Kenmore dishwasher (363.16222100) that isn't getting water into the unit/tube. All the other cycles seem to be working fine. I've replaced to water inlet valve and it's still not getting water into the tub to start the wash. Checked the water line and it's fine. Any ideas?


The only thing left is to replace the main control board ... Dishwashers

Hi :) We have a Bosch slimline dishwasher type SRS56A02 GB/08 - it doesn't draw in water - the timer counts down but nothing happens. We checked these pages and cleaned the filters on the inlet water line but no change :( I saw that it might be the inlet water valve - is this easy to get to - do we need to take off panels? if so, is there a manual available please? Over the past week or so it had got noiser - it was at its quietest while the water was draining out of the machine.


... Dishwashers

No water coming in to dishwasher- there is no valve other than HW valve and that is open- getting water to sink- seems to operate other than no water coming in. Thanks.


Hi,Here is a tip that will help you to find out why water will not come into thedishwasher... Dishwasher Trouble No Water entering Dishwasher ... Frigidaire Dishwashers

I have a Kenmore dishwasher 665.17799990. Not enough water was coming in so I thought that I'd check the screen inside the water inlet valve to see if it was clogged. It was. I cleaned it out,but mistakenly opened the wrong part of the valve looking for the screen and took apart the diaphram assembly. Bad mistake. Now I can't get it back together without it leaking like crazy. I can't remember how it was configured to start with. I put it together once,but it wouldn't shut. I can't afford to buy


... Dishwashers

Not getting water into dishwasher...I get no voltage to water inlet solenoid.....Is there a board that controls this?


... Kenmore 15919 Built-in Dishwasher

My Karcher 330 M has blown two water inlet ( Garden hose inlet ) elbows. Replaced one and then after about 5 min operation shut off the valve on the wand and immediately the new elbow split the same as the first. The garden hose I was using has a shut off valve could this caude the problem?


I have a larger gas powered karcher, just make sure the water going to your karcher is not obstructed from its path. on mine i bought a goodyear hose that can be purchased at northern tools or any hardware store. and use it just for pressure washing. ... Karcher PSI Electric Pressure Washer

My Miele Dishwasher (Excella Series G 2630 SCi) fails to fill. I get the message "Water inlet - Open the stopcock". I checked the water inlet filter and looked for hose kinks to no avail. I even checked the non-return valve. When I start the dishwasher I can hear a low hum (Not the pump) for a few second before the error message displays.


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

My defy dishmaid dishwasher isnt letting in water. I have replaced the pc board and the inlet valve and the salt bucket all to no avail. The inlet valve is not getting power from the pc board.


... Dishwashers

Hello, I just installed a GE profile dishwasher (pwd9280n00ss) into my kitchen. I connected a hose to the valve water inlet, I connected the drain tube from my garbage disposal to the check valve flapper and then the the drain pump asm. When the dishwasher finishes washing the dishes, all the water doesnt drain out. Any ideas how I can correct this?


... GE Dishwashers

Frigidaire Dish Washer. no water is coming into it. Shut off valve under sink is open,float switch isnt stuck. should I shut water off and remove inlet valve?


Verify that water is getting to the valve and verify that 110 volts is getting to the valve. If either one is missing then you know what the problem is. If you have both then replace the valve. ... Dishwashers

Frigidaire Dishwasher Will not fill with water, cheched water valve- no continuity and no 110 volts when the knob is turned to first position. The numbers that were on the valve are C-103/07, 33129014, 672050200016. This unit is in a RV.


Replace water valve. ... Whirlpool GU2400XTP Built-in Dishwasher

Hi there I have a Miele G663 scvi dishwasher. The inlet/outlet light is flashing. I have cleaned the non return valve and filter at the bottom of the machine. I have also removed the water inlet pipe which has a large filter on at the end where it attaches to the water pipe. I have blown through this pipe and it is quite difficult to get air through. Do you think it is a filter that is blocked? If this is the case are they easy to attach to the bottom or the machine or would I have to get


... Miele 24 in. Incognito G663 SCVi Built-in Dishwasher

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

I have a triton XL model GSD6900 that does not fill with water. I replaced the fill valve about 8 months ago. Have checked the inlet valve and coil shows continuity. Ran it thru a cycle and found no voltage at the valve. I assume the problem is in the timer. If this is the case should I have it repaired or buy a new dishwasher.


... GE 24 in. GSD6900J Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1373 seconds