Having problems with your Frigidaire 24 in. FDBB540 Built-in Dishwasher ?

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


Answers :

Repair Help & Product Troubleshooting for Frigidaire 24 in. FDBB540 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

My kitchenaid dishwasher won't wash. The clean light blinks and if I can get it to cycle, it turns on to ''2 minutes'', during which 2 minutes it makes some washer-like sounds but doesn't clean, dry or spit out any water. Before this, I wash having trouble getting my dishes clean. I wash able to get the bottom rack clean using the heavy duty cycle, but the top rack still didn't clean


... KitchenAid Dishwashers

My KDS 19 Kichenaid dishwasher goes thru the wash cycle, but at the end there is about 1/2" water still in the bottom. The punp work OK druing the wash and rinse cycles, but at the end of the drying cycle there still is watere in the bottom.


Would you have the model number at all? It should be on the left edge of the dishwasher's door. Thanks. ... Dishwashers

Kenmore 15789 Ultra Wash Dishwasher Air Dry Light Blinking. Stopped Running, has some water still in the bottom. Cycle Circuit Breaker still no joy.


... Kenmore 24 in. 15782 / 15784 / 15789 Built-in Dishwasher

Dishlex Global 310 model. My dishwasher has water sitting on the bottom of it and it wont drain. I noticed it after I did a cycle of dirty dishes and the 'fast' light was flashing when I went to open it. Which shouldnt have been because it was on a normal wash. The water has been sitting at the bottom for 2 days now and still wont drain! I've taken out all the parts on the bottom which come out and cleaned them. Still no change however.


Just ran another cycle and it was fine ... Dishwashers

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

Upon completion of the washing and drying cycle there is water in the bottom of the dishwasher. We ran the rinse cycle and there was more water in the bottom. Do you have any possible solutions to this problem?


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Dishwashers

Dishwasher repair Dear Guru, I hope you are well this evening. I have a Whirlpool Quietwash Plus dishwasher (940 Series) that will randomly have water sitting in after running through a washing cycle. In addition, some mornings there will randomly be a couple inches of water sitting in the bottom without every running the washer. Need assistance. Any help will be appreciated. Thank you for your time. J


Without model unablr to look up exact unit, but in genreral, either ther is a blockage/clog in oyour drain line not alowing complete drain of cycle, as far as never really washing, i would look into perhaps a faulty/ sloppy door switch assembly. if f ... Dishwashers

Dishwasher Odor Our dishwasher leaves dishes and glassware with a sulfer odor after the wash cycle. We have run vinegar through it, use jet dry, and use 1 tablespoon of dry detergent. All suggestions made by the "customer support". None of these have led to a permanent solution. We're about ready to "kick this to the curb". Any suggestions? I've checked filters and there doesn't appear to be any standing water. We have city water and there isn't an odor when you drink it.


I would disconnect the drain hose from the sink trap and drain the water out into a pot -- just to make sure there's nothing in the hose that can't get out. Check the sink trap too to make sure it's not holding something. Run an empty dishwasher us ... Asko 24 in. D3250 Built-in Dishwasher

Dishwasher is not draining during washing cycle. Water is always sitting at bottom of dishwasher pan. Also, when the draining cycle is going on the dishwasher (?) pump made a strange sound (not smooth running)


Locked rotor on the bottom of the machine. If you remove the bottom plate of the dishwasher where the water valve and electrical hook up is the motor is right there. If the rotor on the motor is locked up the dishwasher will not drain.. If you take ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Kenmore Limited Edition Ultra Wash Dishwasher. Model 665 15892100, Ser. FL4910642 E71195, Stock #15892. Loaded dishwasher, started it, and went to store. When we came back, it appeared cycle had not completed (greasy and wet dishes) and the dry cycle had definitely not run. Bottom of dishwasher is filled with water. Tried to cancel/start the machine but control is completely blank and does not respond.


Hello,Welcome to FixYa.The issue with your dishwasher is more than likely the "thermal fuse" inside the control panel...it is all too common with those machines unfortunately.I've at ... Dishwashers

I have a Hotpoint Aquarius FDW 20 dishwasher. Prewash and Wash lights were flashing, machine had stopped and water was at the bottom of the machine. What does this indicate? After removing some debris from the water drainage pump, then reassembling the machine, I now get the pre-wash LED flashing and a motor operating, but no futher progress into the wash cycle. What does this mean?


Dishwasher always full of water at the end of cycle ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hi, I have a 3 year old Nemo F&P dishwasher which turns itself on and off for about 3 seconds each on/off continually.Eventually it does get enough water to wash but never goes into the wash cycle properly, ie the water just sits at the bottom. We dont think it's water pressure and it was working fine until recently.Could it be an electrical problem with the signal to fill properly not getting through? Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing ... Fisher and Paykel Dishwashers

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

Dishwasher is less than a year old. Once in a while it will stop about 10 minutes into the cycle, then the display lights will blink. Sometimes it will stop and the lights wont blink so we will come back later thinking it is done only to open it up and there is water sitting in the bottom. Doesnt happen all the time but sometimes and yesterday happened about 10 times finally gave up. I can cancel and restart the cycle but the same thing happens.


I would most likely guess a faulty latch....it will cancel the cycle, thinking that the door has opened, and the lights will flash. After a certain amount of time, it might "time out" and reset and the lights would stop flashing. Unfortunately it's ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Hi, I have an LG LDS4821 dishwasher and it appears to stop working properly. The dishes don't seem to be cleaned at all. It seems like the spray arms are not spraying the dishes as the dishes are still dry/dirty after a normal wash cycle. I did notice that the detergent was used during the wash, and a trail of white residue was at the bottom of the tub. I can hear water pumping into the dishwasher, but when I opened it during a wash cycle, there was a puddle of water at the bottom of the


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDS4821 24 in. Built-in Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Leaking dishwasher The dishwasher leaks a stream of water at the base -bottom left corner whenever it goes into the final rinse cycle. It does not leak when it is in the wash mode. This leak just seemed to develop suddenly. There was no build up -ie a small stream of water. I just noticed a big puddle on the floor one day after dishwasher had completed its cycle water leak in the left side ,bottom ,husband states a small drip,drip and we do not know what to do or replace. No water standing


I just had this same problem and it was caused by a small plastic seal on the bottom of the door. My friend owns an appliance store and he said this is a common problem for this model of dishwasher. The part was $68 and the labor was $60. I could ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

My dishwasher won't drain. It runs through the whole wash and dry cycle...and when I open it to unload the dishes the bottom is filled with standing water. None of the lines that I can see appear to be kinked, and I'm not sure what else to check. I inistalled the dishwasher myself becasue my husband was working out of town...this was about a year ago. Haven't had any problems with it until now. Thanks for any help or suggestions you're able to offer. Christine Fitzpatrick


If you hear the drain pump run after wash and rinse cycles then it is likely the problem is in the kitchen drain end. Have you got a disposal unit in the kitchen sink. Sometime it is full and causing a block.\015\012\015\012If you don't h ... Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

My G.E. dishwasher washes, dries, etc., ok but when the cycle is finished and the washer says "dishes clean" on the panel there is still about 2" of water left in the bottom of dishwasher. What should I do about this?


Hello. The water left in the bottom indicates that there is a partial blockage in the drain. Begin by removing the lower front panel from the dishwasher. To do this you will need a phillips head screwdriver [size 2] and a flash light. Generally ... Maytag Dishwasher

I have a ge dishwasher model GSD5211 purchased in may 2006. Water appears to be dripping from under the front ss panel to the bottom of thepanel. I cannot open it to check the source of the leak. Alo found that the leak occurs midway of the washing complete cycle. It also seems that the leak during a particular cycle. Not sure which as just two indicator lights stay on thepots and pans and heated dry. Please help


You may want to inspect the seal around the door to make sure it's not worn out or has some foreign material stuck to it causing it to not make a watertight seal during operation. If you don't see any problems there, then you should pull the machine ... Dishwashers

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2423 seconds