Having problems with your Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher ?

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


Answers :

Repair Help & Product Troubleshooting for Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

I have a Hotpoint Aquarius dishwasher (FDW60) The 3hr and 12hr lights are on and the machine won't respond to any other buttons pushed therefore I have not been able to reset the machine (that is if the delay start has actually been activated). It started with the machine not draining however I was able to drain it manually so that rules out any blockages. Please help...The manual doesn't have any troubleshooting advice for those lights... Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. When 3hr (Prewash) and 12hr (drying) light flashes it indicates\015\012the fault in the heating ci ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a frigidaire dishwasher fdb520rhb2. Lately, at the end of the cycle the high temp wash and heat dry light will start blinking. The cycle does not finish. Cannot find the error codes in manual. Thanks.


... Frigidaire Dishwashers

2 brand new Kenmore elite dishwashers - All hookups checked and correct. Start buttons blink - cycles will not start. 1 washer ran for about 10 seconds - then the light started blinking. Troubleshooting in manual says light will blink if the door is not closed. They seem pretty closed. Dishwashers leveled and plumb. Tried it mounted, and unmounted. No Luck. Thanks


These dishwashers have a safety feature. The door has to be closed within 3 seconds of pushing the start button. If the cycle is interrupted at all by opening the door or pushing something while started you will have to push the start button to resum ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My dishwasher will not start. It is a frigidaire / electrolux FDB1050REQ. I have checked thepower....and reset the circuit breaker.......then pushed the start button.....the light comes on on the front of the washer like normal but no water starts filling. I have jiggled the anti water overfill device but still nothing. HELP!!! The front of the dishwasher says Frigidaire, however, the inside of the door where the model# is says Electrolux


... Frigidaire Dishwashers

I have a KitchenAid dishwasher, model KUDP02FR. The "normal" cycle light is flashing. When I push "cancel" or "resume/start", they start flashing as well, but the dishwasher won't start. I turned off the power and turned it back on. The "normal" light still flashes, but when I press "resume" it all starts over again. Any ideas? I can't find this in the troubleshooting guide I have. Thanks.


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid KUDI01TBK Dishwasher

I have a Maytag Quiet Series Dishwasher although it is not stainless steel, it is white. My dishwasher, shuts, and the lights come on when I push it but it will not start! Yesterday after a few attempts pushing cancel and so on, I smelled a STRONG concentrated smell of the liquid dishwashing detergent inside the dishwasher, but it never came on. Can you help, I cannot find the manual for this appliance, it came withour home when we purchased it in 2006, and it was brand new.


Here is the manual.\015\012\015\012http://shared.whirlpoolcorp.com/assets/pdfs/literature/Use%20and%20Ca ... Maytag 24 in. MDB5601AWS Stainless Steel Built-in Dishwasher

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

My dishwasher will not start when I push the start button only the green light flashes I checked every thing I could. I checked the manual for solutions found none. Its a kenmore dishwasher model no. 587.1619.


... Dishwashers

Re; Smeg DWD612CSS dishwasher. Please help. On setting our dishwasher to operate overnight, we were awoken by a loud bang only to find a strong rubber burning smell and the trip had blown. After investigating we found that the part no DWF 409 interface filter required replacing which we have done. Now however the dishwasher runs to the middle of its cycle and stops. The troubleshooting page of the manual tells us code E3 applies i.e.first 2 phase lights are lit and states "The appliance is not


I would first look for anything that may be stuck anywhere in the machine that may be causing it to come up with an error. Possibly something that was in the dishwasher is making it think it can pump out the water even though it is draining.\01 ... Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

Frigidaire Dishwasher Model:FDB1050RECO - When i push the start button all lights go out. I have to open and shut the door in order to start the unit this sometimes works...


Same problem, wash light would flash, just like if the door was open during the wash cycle....took door apart and suspected the door switch was bad, fiddled with the wires that go to the door switch and the washer worked after that. so i had the doo ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

My Miele G2430 dishwasher stops right after draining in the first minute or so after starting, and the intake and drain light comes on. The solenoid at the end of the intake hose then clicks and the light begins to flash. I applied suction to the intake hose to determine if the solenoid is working, and the valve does open and close. There has been no error code displayed. I cleaned all of the parts and filters referred to in the owner manual.


For a drainage fault heres what the miele service manual says for your machine\015\012Water present in appliance and is not being drained off. The display shows Drain fault F11. The buzzer is activated for 2 minutes. ... Miele Optima G2430SCi Stainless Steel Built-in Dishwasher

My Frigidaire dishwasher won't come on. The cycle lights only flash when I push start.


... Frigidaire Dishwashers

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Matag MDBH940AWS dishwasher: Push start and light comes on but dw doesn't start - push again and light goes out but pump starts running but no water enters, push again , it shuts off ;; past problem never addresses is delay feature stopped working , no lights come on when delay buttons are pushed, so... control head in door replacement in order? Thanks , [email protected]


... Maytag 24 in. MDBH940AWS Built-in Dishwasher

SHE4AM15UC/05 dishwasher will not start When I turn on light for regular wash lights up but will not start after I push start button. When I turned it on the rinse agent light was on, I added some and that light is no longer on but after several tries it will no start. Electricity went out yesterday but dishwasher was no on when it went out..


... Bosch SHE4AM15SS Stainless Steel 24 in. Dishwasher

My dishwasher won't start (Series 300 purchased 14 months ago). The following lights are on: light wash,hi temp wash,sanitize, locked and the start /resume light is flashing put goes out when pushed and the machine does not start when closed. there has been an on going problem with the regular wash light not coming on when pushed.


Hi\015\012\015\012It may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting t ... Maytag 24 in. MDB9750AW Dishwasher

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

My Ariston LV 62 dishwasher wont start and is diplaying 2 flashing lights, however this error code is not explained in the manual. Can anyone help???


... Dishwashers

I just replaced the heating element and it was working fine for about a week. Yesterday, the soak and scour light (which I've never even used) started blinking constantly. The dishwasher, Model GU2400XTPB3, won't let me even enter the reset code. I need to know if it's something we can fix without paying for another part/service by finding a manual. Thank you.


... Whirlpool Dishwashers

Have a whirlpool G2P DWI / 1 WH integrated dishwasher - when put on [70C] it seems to work ok and washes dishes but then after what seems to be the full cycle it just beeps continuosly - when opened the start button is flashing and the green light is on under the pre-rinse symbol. There are two bar codes down the side: 8542 347 15810 and 33 0451 014488. It's been in for about 3 years and have had no problems with it. Can't find instruction manual.


... Whirlpool Dishwashers

I have a Kenmore dishwasher 665.16022402 that is locked out at the board.( the clean light flashes continually & wont allow it to run) I don't have the manual to find the reset code and troubleshoot. There didn't seem to be any proublems till now.??????? any help?


... Kenmore 24 in. 16032 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1985 seconds