Having problems with your Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher ?

I have a frigidaire dishwasher - model number PLDB998AC1. There are two spray arms in this dishwasher - lower and upper. The lower works fine but the upper spray arms are not spinning. There is what I think adequate water pressure coming in from the top but no movement on the upper spray arm. Here is what I know: 1) The water pressure and spray arms alternate between top and bottom. 2) The upper spray arm moves freely when I push it gently. 3) I have removed the pump and cleaned out an


Answers :

Repair Help & Product Troubleshooting for Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a frigidaire dishwasher - model number PLDB998AC1. There are two spray arms in this dishwasher - lower and upper. The lower works fine but the upper spray arms are not spinning. There is what I think adequate water pressure coming in from the top but no movement on the upper spray arm. Here is what I know: 1) The water pressure and spray arms alternate between top and bottom. 2) The upper spray arm moves freely when I push it gently. 3) I have removed the pump and cleaned out an


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

I have a Frigidaire dishwasher and there is not any water coming out of the top wash arm. There is good water pressure coming out of the lower washarm. I pulled out the dishwasher and can see the water going to the top washarm through the tube and it goes up very slowly. I took out the "check ball" below the lower washarm and it worked good. I put the "check ball" back in and ran the machine on "Upper Rack" and it still does not have any water coming out of the upper washarm. It doesn't seem lik


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check that there is no gunk or mold\015\012behind the filter screen and under the cover at the bottom. N ... Frigidaire PLDB998A Built-in Dishwasher

I have a Whirlpool GU2500XTPQ3 dishwasher that is about 5 years old. The dishes in the top basket do not get clean. I checked the water tube that feeds the upper spray arm and the top spray and there aren't any obstructions. Our water pressure and temperature are suitable. Could the pump be plugged or otherwise lose its ability to circulate enough water to adequately feed the upper sprayers? How can I check on that?


Hello,\015\012\015\012Welcome to FixYa,\015\012\015\012Based on your description as well as all you`ve done on your own I`d suspect you`re on the right track with the plugged pump suspicion.\015\012\015\012The plac ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Upper spray arm is not turning and I don't think water is coming out. Dishes on top are not coming clean. Dishes on bottom are clean (as clean as they get with this dishwasher). How do I remove upper spray arm. Also I'm not sure how to remove lower dish rack to access upper spray arm. Any help appreicated. Kitchenaid model KUDP01FLSS5 Chris


Hi Chris,It sounds to me like a restriction in the pump. I put together some information here on cleaning it out. If you try these please give me some feedback as to if they help or not.Thanks! ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Dishwasher, nautilus, doesn't spray water out the top arm? I'm haivng to wash dishes 2 times, and still no better results. I've tried opening the door fast during a water cycle to see which is the problem - can only figure it is the upper arm, the lower arm seems to have water coming out, can't tell if the tower raises completely up.


The jets on the arms can sometimes get blocked with food bits that have got past the filter. This reduces the water flow and rotation of the arms.The arms are easy to remove without tools (they are intended to be removed by the user). ... GE Nautilus 24" Built-in Dishwasher

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

Dishes all cloudy and spotty. Maytag Intellisense plus 1996 dishwasher. I have real hard water that leave white calcium build up. I can remove and clean all of the lower spray arms and filter. How do I remove top spray arm to remand remove deposits? The motor sounds good, hot water, fill ok. On the inside top of center of arm where it meets the center input connection there is gunk to remove. How do I get to it? remove arm? thanks


The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your d ... Danby 22 in. DDW399 Free-standing Dishwasher

Dishwasher Water is not going through upper and lower spray arms. Checked overfill protector switch, inlet valve, inlet valve screen, pump blades move freely, Pumb motor is working , Water enters into machine but does not go throught spray arms. Water heats up, Machine will go through all cycles but without water going through spray arms. 650 / 690 series gldb656jso


... Dishwashers

I have a kitchen aid dishwasher. The upper spray arm is getting water and getting enough water pressure but wont seem to spin. Ive ran a lot of tests but nothing. ive cleaned out the spray arm and port that gets water to the spray arm. Cant seem to fix it. Any ideas?


Hi,When my wife started complaining about her dishwasher not getting the top rack clean this is what I found and I wrote a tip about it...Dishwasher Spray Arms not Spinning ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

My LG LDF7810ST dishwasher does not spray water from the middle or upper spray arms, therefore the dishes don't wash properly. Even when I ask for a top load only, the bottom spray arm is the only one moving (which I would expect that it shouldn't move at all since I've requested a top load only) I checked the spray arms as best I can to make sure that they're not clogged.


... LG 24 in. LDF7810 Built-in Dishwasher

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

I have a Frigidaire Ultra Quiet Plus dishwasher. The top spray arm isn't spinning during wash. The bottom spins fine and I can spin the top freely by hand. It appears there is not enough water pressure gettig to the top spray arm. Any suggestions? Tanks, Sam


I may have the answer. I had what sounded to be the same problem. I found the dishes were dirty after they were cleaned, but I found there may have been a big pot lid blocking the upper arm. I decided to run the machine again, and after a bit open ... Frigidaire Dishwashers

Kenmore BuiltIn Dishwasher Stock 17512 Model 17512200 Type 575-0 Serail FM3309375 Probelm: Water sprays out of lower arm weakly, and not out of upper arm at all. Action taken: Unscrewed the 4 screws holding down the item underneath the lower spray arm, and then the small item under that. Found major refuse from years gone by, removed, cleaned. Reassembled, same issue. I suspect I have to get 1 more level down, to the intake for the pump? found 2 screws to remove, but was not suc


... Dishwashers

I have a Frigidaire dishwasher, FDB-1100RHC, that is not cleaning dishes. My fiance cleaned the trap at the bottom of the washer, removing both the small basket and the larger mesh grid. After replacing both, the washer doesn't seem to have enough water pressure to spin the lower and/or upper arms. If I interrupt a cycle and open the door, water is dribbling out of the upper arms, but they are not rotating and do not move from whatever position you place them in. Both arms are completely uno


Hello :)don't feel bad, I run into this kind of problem at least once a week.\015\012It does sound like the pressure isn't there so you're not getting water to the upper spray arm. What you need to do is take the pump apart, which i ... Frigidaire Dishwashers

Follow-up I've removed the lower arm, I'll spend some time and see whether I can get the pobem sorted out. My wife noticed the the detergent was smeared all over the door and repeated tries didn't get it out. Therefore, the water is not spraying. I can confirm the water is filling on the bottom and draining. The heater is working well. I am thinking there is no pressure to send the water through the tubing to the upper and lower arms. The motor is hot to touch (118 degrees with my temp probe). I


... Kenmore 24 in. 15199 / 15194 / 15192 Built-in Dishwasher

My maytag dishwasher lower and upper spray arms are working intermittently. Sometimes there is plenty of water spraying around, other times, I can hear what sounds like the motor running but the arms are not moving (or not moving much) and very little water is splashing around. When this happens, the detergent sometimes doesn't even get washed out of its compartment.


Pour 1 Cup of Muriatic Acid (Can be purchased at your local Pool Supply Store) into the bottom of the washer and a little in the soap dish. Run the Dishwasher through 5 cycles. Check to see If this helps. If not Try the same process with CLR house cl ... Maytag 24 in. MDB4000 Built-in Dishwasher

Frigidaire dishwasher (Electrolux FDB750RCB0) does not move water through the hose to the upper wash/spray bar. The lower wash/spray bar has pressure enough to turn. With the dish washer out from under the counter I can see the water rise very slowly up the translucent hose. If I remove the check ball under the stem assembly in the motor in the bottom of the tub, water flows, but I'm not sure if the top bar turns then (with the door open I see water coming down from the top, but never saw


... Dishwashers

Top arm of dishwasher does not spin or spray. it is a 7 yr old frigidaire dishwasher, model #gldb957ab. The dishes on the lower rack also do not get clean. this just started recently. the mid level sprayer will turn by hand but doesn't move during cycles. seems like it would be there is no water coming to the top of dishwasher while it is running.


... Frigidaire 24 in. GLDB957A - Multiple Color Energy Star® Built-in Dishwasher

Dishwasher fix water does not go through the spray,. the upper hand an lower hand are clean , the pump does operate to empty the dishwasher . I do smell like some burning smell when I turn the dishwaher on, the water start running for 1 minute or 2 than stop shortly and doesn t reach the arm then the dishwasher becomes hot inside . Thank you


Something has gotten passed the screen and is jamming your pump impeller pull lower spray arm pull screen and see if you can find what is jamming the impeller and remove it drain pump is separate ... Maytag MDB7100AWB Dishwasher

Triton XL Dishwasher has difficulty cleaning the top rack. Water sprays in the bottom but does not seem to be as high pressure as it should be. I have taken off the water line to the top and middle rotating arms and they are clear.


Hello stove.... Typically the dishwasher water supply is located under the kitchen sink, so it has the same (should have the same) water pressure as the hot water to your sink. Turn on the hot water into the kitchen sink a ... GE Tritonr XL GSD6260JCC Dishwasher

Component failure Actually a Kuppersbusch IGV 645.2 Dishwasher There is a plastic conduit which takes water from the base of the machine to the upper spray arm. This now comes adrift from its connection at the base (behind the lower spray arm) on every cycle, resulting in poor or incomplete washing. It can be replaced easily and seems firmly inserted when done but is always adrift again by the end of the next cycle. Anyone any ideas?


Put a bead of silicone on the tube connection and let it set up good before running. If the tube is in good shape and only comes loose this should be an easy fix. ... Whirlpool GU2400XTP Built-in Dishwasher

I have a GE GLD6000 series dishwasher. The spray arm on the top rack and the srpay arm on the top of the unit are not turning. I have checked the water pressure and it is fine. Also the conduits are


... GE Dishwashers

The dishwasher doesn't seem to have nearly enough water in it. The upper sprayer arm doesn't seem to be spinning when running (I open the door and look really quick) and the lower one looks like it barely spins and barely sprays water. The dishes are barely wet and the soap is just laying on the bottom. The water is on, there are no kinks in the supply line. It sounds like it is running, and pumps pumping, but being brand new I am not sure what it should sound like. It certainly doesn't sound li


I would lift the drain pipe higher. approx. 1/2 the height of the dishwasher . also rechack incomming water supply. Make sure no blockages and the like. Try again. ... Bosch Dishwashers

The dishwasher is not cleaning the dishes at all, so far I have done the following: Checked both sprayer arms and they move freely and do not appear to be clogged (I ran stiff wire thru holes in each The float is not stuck and moves up/down easily The water leavel in bottom of tub does appear to be low - so I added water filiing tub to heating coil - however this did not help and the water did not spray on lower or upper racks - this is an older model Kenmore Ultra Wash WHAT DO I NEED TO CHECK N


Heating element may have burned out. Check water temp during wash--should read between 130 to 140 F.If not the heating element,you may have to replace pump-motor assembly or wash impeller.Hope this helps. ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2055 seconds