Having problems with your Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher ?

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


Answers :

It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.
\015\012So remove the panel and disconnect the wires, check all leads to the panel and the board. Now check the inlet/outlet valves /pump. Make sure that there are no loose leads or corroded terminals.
\015\012 If none of these works the fault points to the program controller unit as the cycles seems to be in disarray.
Repair Help & Product Troubleshooting for Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.\015\012So remove the panel and disconnect the wires, check all lead ... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Dishwasher malfunction MOST OF THE TIME it shuts itself down before fully filling with water - SOMETIMES it doesn't shut down until the minute the wash pump starts - SOMETIMES it washes for 10 or 20 minutes before shutting down - SOMETIMES it will even run a whole cycle, BUT it doesn't open the soap dispenser door - tried doing a diagnostic run but after it turned on all the lights on the panel it started to fill with water and shut itself down......... HELP


Follow this steps and fix it. God bless youFloat Switch\012\012\012The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. Check the ... Dishwashers

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

Smeg DF612S All starts well but after 40 minutes stops with a beep and will not progress to the main wash cycle. Instead all programme lights come on (located on the left), along with the first 2 phase lights (the first two of the lights on the right hand panel). This indicates error code 3 (cannot pump out water), but water is entering and draining perfectly. Please advise.


Check to make sure there r no kinks’ in the drain line or\015\012that it is not clogged it sounds like the sensor is tripping because there is\015\012too much strain on the pump just like a breaker. ... Smeg 24 in. DWI612 Built-in Dishwasher

We have a Maytag MDBH950AWS Dishwasher that won't start. When you press the start button the cycle light, washing light , heated dry, sanitize and extra rinse lights all come on the dishwasher fills with water and after a couple of minutes it shuts off. Any ideas what is wrong? Thanks


I have Miele incognito that when I shut the door it does not turn on? Not sure why it stopped working all the sudden ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

Kenmore elite 1393 worked fine for a week or two then began to stop in mid cycle,we could drain the water and try again but would shut off almost immediately. sometimes trying to restart it there would be NO power to any buttons, after waiting for awhile the buttons/lights would work again but the washer would not run a full cycle.blue light would light then go out within a minute or so.


... Dishwashers

We have a KitchenAid dishwasher (KUDI01FLSS6) which has not been working properly for a long time. We have the dreaded green blinking light mystery. We understand that this could indicate several different problems. We have found that if we run the sink water until it is hot, then start the dishwasher, and then after ten minutes we open then shut the door, it will consistently run the full cycle perfectly. Does this give you any hint of what might be the problem component -sensor, element, the


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hi, The timer lights up on the door when wash cycle is pressed --inside fills with water but after a minute no action -it won't keep going and the timer freezes but does not shut off the drain button won't activate but drain hose is clear? Thanks


Sounds like the touch panel/ before replacing it ch the ribon connections . where it plugs into the pc control . use a ereaser to clean and replug . . . also make sure the door inter lock is working properly .. mm ... Maytag MDB9600A Jetclean II Built-in Dishwasher

When you start the unit it engages and water flows within 4-5 minutes it shuts itself off with drainage intake light flashing. Cleaned filter and checked garbage disposal unit-same result. Changed cycles-same result.


HI. You can easily "reboot" your unit by unplugging the appliance for five minutes. This will force the main control sector to reset its programming. If you cannot reach the power plug, you can simply shutdown the appropriate circuit breaker for five ... Dishwashers

Hi. Our DS603I dishwasher starts on the Rinse cycle on its own - it beeps, red light flashing and no water entering the tub. It does this even if it is open. Similarly, when we try to turn it on to do a normal or heavy cycle, it starts (making quiet a loud noise) and then goes to the Rinse cycle, beeping, red light flashing, no water going into the tub. The pump wheel is turning. We can't find any blockages in the tubes. We have power-cycled it many times. Please help!


Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012\015\012\015\012\015\012 ... Fisher DS603W / DS603B / DS603I Dishwasher

On the MIELE G881 SCI plus -3 the cycle stops after about 2-3 minutes (enough time to purge the remaining water and fill the dish washer with new water). Then after 10 minutes it abandons de cycle and shows the red light "intake - purging". When i open the washer, the water inside is NOT warm.


Hello, Welcome to FixYa.I'll start by saying on many Miele different issues can manifest in a similar scenario, water valve, leaks, etc. and then the error lights. ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

Cycle interrruption Recently, about 20 minutes into the wash cycle, the unit shuts down and the lights start blinking - usually "Pots & Pans" & "Quick Rinse" simultaneously. No other buttons respond and I cannot get it to finish the cycle. Only shutting down the unit at the fuse box eliminates the lights. I've checked for blockages and nothing found. Manual does not offer any help or suggestions. Any ideas??


Relace control board. ... Kenmore 24 in. 16032 Built-in Dishwasher

Whirlpool dishwasher DU945PWPQ2 four year old machine - never used. Water lines are attached properly and are clear. When dishwasher is turned on the wash cycle light turns on. cycle completes but water does not enter the machine.Water does not enter the machine.


... Dishwashers

When I start the top drawer it defaults to 5 minutes (with the lights Heavy, Fast, Rinse highlighted) runs for a couple minutes, then stops and the LED starts randomly cycling through all kinds of codes very quickly. There is water in the tub that has not drained after completing the couple minutes of operation. This cycle repeats itself if I hit the power button again after the LED starts freaking out. The 5 min cycle shows in the LED, sometimes with the no circulation error, sometimes with the


Here is the solution: \015\012http://applianceguru.com/forum1/24814.html ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Hi. IKEA Whirlpool DWFA10 dishwasher.Firstly, when switching on the machine to befin the programme the machine does not pump residual water away.It then begins its cycle (in this case the pre-rinse cycle).After 12 or so minutes,when the cycle finishes and the water should be pumped away,the machine stops and the green warning light keeps flashing 4 times intermitantly.


... Dishwashers

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

The dish washer ran its full cycle but won't shut off. the little pump motor in the very bottom keeps cycling water in the bottom. it won't shut off when you open the door, it won't shut off when you push the power button and the front switches won't respond. the little light on the front of the dish washer is blinking and it has never done that befor normally the lites are always on solid.....


The drain stuck cycle ( I presume you mean drain pump running constantly ) are directly related with overfill scenarios for Asko dishwashers of this ... Asko D3122XL 24 in Builtin Dishwasher

GLDB958AQ0 Lights on panel light up then go off after a few seconds upon startup. Sometimes they stay on and the timer in the display window counts down the minutes, but in either case no sounds come from the dishwasher nor does any water enter the unit. The water is turned on and there are no kinks in the supply line. I removed the water valve and could not blow through it. Upon applying current to the valve I could blow through it but it still seemed restricted. Should I be able to blow thr


... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

Eurotech Model EDW254EWXX runs a 13 minutes cycle before washing like usual, but now it is getting stuck and not doing anything during that 13 minute cycle. No water is running, and it makes NO noise at all. We are not getting any errors displayed. I have unplugged it, and shut off the circuit breaker for 20 minutes, but the problem is still there.


... EuroTech 23 in. EDW254E Built-in Dishwasher

Kitchenaid model KUDIO1ILBL6 The lights for Heavy Cycle ,Normal Cycle and Cancel blinking at the sametime constantly. The tech sheet is missing and the unit is appox. 5years old.have shut power down for 5 minutes .When power turn back on only the Heavy Cycle light blinks costantly. Have Ohmed out the door switches and check adjustment OK. Checked board strips and plugs for good clean and tight connections OK. Thanks


Hi, You need to reset the unit by pushing the buttons. Push the heated wash/heated dry a few times. All the lights will light up and the dishwasher will continue its . Let ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

Soap dispenser doesn''t open during the cycle. There seems to be no water being dispersed. The cycle stops at the 1-minute mark and then does not shut off. When the door is opened mid-cycle, the motor does not shut off.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on the description of the unit not filling with water and the machine doesn`t stop if the door is opened explains almost everything, thanks for such detail.\01 ... Bosch Dishwashers

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2119 seconds