Having problems with your Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher ?

Cycle stops, lights blink

\015 This dishwasher will run for a time, and then stop and the display lights will blink.The cycle will not restart.\015

Answers :

I have the same problem, same model. Driving me nuts. Help!
Repair Help & Product Troubleshooting for Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My GU 120 stops mid cycle and the indicator light starts blinking a humming whirring sound preceeds the ctcle stop nad light blinking. Pressing the button for 5 seconds causes the flashing light to extinguish but the sound continues untill the unit stops. It does not complete the full cycle. Your help would be appreciated. Tony


... Whirlpool Dishwashers

Dishwasher is less than a year old. Once in a while it will stop about 10 minutes into the cycle, then the display lights will blink. Sometimes it will stop and the lights wont blink so we will come back later thinking it is done only to open it up and there is water sitting in the bottom. Doesnt happen all the time but sometimes and yesterday happened about 10 times finally gave up. I can cancel and restart the cycle but the same thing happens.


I would most likely guess a faulty latch....it will cancel the cycle, thinking that the door has opened, and the lights will flash. After a certain amount of time, it might "time out" and reset and the lights would stop flashing. Unfortunately it's ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Dishwasher takes about 24-36 hours....yes hours....to complete the cycle because it stops....for sometimes more than an hour and then starts again on its own. When it stops the green light blinks. No explanation in the manual for a blinking green light. It will eventually complete the cycle, but who has two days to do a load of dishes?


... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

Whirlpool Gold Quiet Partner IV Dishwasher, Model GU1500XTKT0, Serial number FL4104935, Type 575-0, during a Rinse Only cycle suddenly the cycle light began constantly blinking, which could not canceled or stopped nor placed into diagnostic cycle or other wash cycle. The repairman checked everything and decided problem was Electronic Control Module, which he replaced; blinking Rinse Only went off, but Normal Wash is now constantly blinking and repairman seemed confused and is wanting to repla


... Whirlpool Dishwashers

My dishwasher's clean light will not stop blinking and it will not allow me to start a new cycle. I have canceled the cycle unplugged it and let it sit but the light is still blinking


Your\015\012dishwasher will do this as a safety in case the element is broken and\015\012feeding electrical current into the water. Sometimes just a false\015\012reading.Reset your console by pressing: ... Whirlpool 24 in. DU1055XTPS Stainless Steel Built-in Dishwasher

Pots/pan light blinks alternately with the normal wash button. Sometimes the cycle will start and then the lights come on. Once they start blinking, the cycle stops and I can't get it to start again. Unplugging it for a few days has worked a few times. But it just keeps getting more frequent. If it does start up, it heats fine and washes perfectly.


... Whirlpool DU1055XTSQ Built-in Dishwasher

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

Dishwasher DU1100. Odd behaviour during cycle: "Washing" light goes off and sound of washing stops. "Normal" light starts blinking and "soak and scour" light comes on (it was off before). No sound from washer. This persists for at least 10 hours. After that, the lights go off. Is this normal behaviour? It would appear tha the drying cycle did not go.


No it is not normal. It appears that either the membrane switch pad has failed or the control board has failed. ... Whirlpool Dishwashers

Built in model MDB5601AWB- about 3 years old. The touch panel stopped working..no lights would come on when touched. Tried it a couple of days later. Lights came on..finished a cycle. after satying in the wash mode for a few hours. Then lights started flashing on and off. At that point I shut it off at fuse box since I couldn't get lights to stop blinking and haven't trusted to use since


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. From what you have described it seems to be the ... Maytag Dishwashers

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

We have the G841SC+ Miele dishwasher. The intake/drain light blinks and the cycle stops on economy and sani wash before the end light comes on. The normal cycle seems to be able to complete a full cycle. Is there anything we can check.


... Miele Dishwashers

Whirlpool dishwasher stops a few minutes after cycle begins then light blinks


... Maytag Dishwashers

"Quick Rinse" light blinks constantly, unable to select "start" unable to select "normal wash" sometimes can select "pots and pans" but still not able to start. Was working normally, when it stopped at end or pre-rinse to start the main washing cycle, the "quick rinse" light came on blinking, and no other button works except as described above. Thanks,


Hi,\015\012 \015\012Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow ... Dishwashers

Du1145xtpba quietpartner II starts then stops shortly into cycle and the normal wash light just blinks, if you hit cancel then both lights will flash when unplugging/reconnecting ribbon cable from control board it will complete 1 cycle and more often than not will do the same thing


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Was running a wash cycle lastnight and it stopped running and the clean (green) light is blinking and won't turn off. When I push the Start button, there is a red blinking light. Help. It is a Kenmore Stock # 16033 Type 575-0 and Model 665.16033401.


Is your washer a front load? Does it have a small window where you read the stages or minutes left?\015\012If so is there a code flashing in thet window?\015\012Also what year is your model? ... Kenmore Dishwashers

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

My kenmore dishwasher, model 15822, just stopped working. The quick rinse light is blinking. The only other buttons that work are the pots & pans light which blinks when pushed, and the cancel button which will run through the 2 minute cancel cycle.


These are known to develop sticky switch contact pads. They stick in the contacted position and stifle the panel. Sometimes heat can be applied with a hair dryer to release them and make the unit function again. This is more than likely a temporary f ... Kenmore Dishwashers

I have a modulogic ADP951.seemed to be stuck on cycle today so I stopped it. water did not drain. I cleaned all rotors and filters and re started. Water drained however start light now flashing. Have tried holding for 5 secconds to re start but only starts pumping out water (of which there is none) and then stops. Light continues to blink. Any other tricks??


I am assuming you have not tried the reset by turning mains power off and then on.\015\012\015\012One of the reasons for being stuck in the wash cycle is the water temperature is not reaching the right level. This could be due to heater ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My Kenmore ULTRA WASH dishwasher model #1603* does not respond to any command. When I select a desired washing I only get a blinking light on my selection and nothing else. If I select ''Cancel/Drain'' it blinks as well. I receive no response at all if I select ''Start/Resume''. To stop the blinking I must turn off the circuit breaker. When I restore the power, the control board is not lit, however, selecting any of the wash cycles and the blinking starts once again. The manual refers to a blink


Replace timer/program module\015\012Vitally ... Kenmore Dishwashers

I have a Whirlpool gold dishwasher GU2275xtvy0. It will stop during the middle of a cycle, all the lights will go out after a while the lights come back on with the startresume light blinking. It wil start back after pushing startresume only to do the same thing 10 or so min. later. Any idea what could be wrong or what to check?


... Dishwashers

Will not go through a compleate cycle and then the clean light comes on and blinks 7 steady blinks and stops the blinks again and i cant start the dishwasher unless i reset the dishwasher and then it does the same thing


Hi angelbme1,\015\012\015\012I'm Harvey the Master Plumber.\015\012\015\012Your problem is: will not go through a compleate cycle and then the clean light comes on and blinks 7 steady blinks and stops the blinks again and i c ... Dishwashers

Kenmore dishwasher Mod.#66516039403 stop running thru cycles,clean light blinking


... Kenmore Dishwashers

Cycle stops, lights blink


I have the same problem, same model. Driving me nuts. Help! ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1298 seconds