Having problems with your Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher ?

My frigidaire dishwasher leaks from the bottom right of the door. It forms a puddle while running a load of dishes. Looks like the seal is gone underneath the door on the right side. Any idea how to replace this seal? Thanks.


Answers :

One possible solution to your problem could be as follows... Could have been little regular soap or something put in that made it suds up causing it to leak out of the front and sometimes not to drain all water out. Pouring vegetable oil into the dish washer tub will remove the suds. After running vegetable oil for about 5 minutes, pour 2 cups of vinegar in to the tub and run it on the hottest longest cycle with no dishes in it. This will clean the residue out and what ever "gunk" may be in the internal parts. Use Only powder detergent. No gel and No tabs. These 2 cause a build-up over a period of time of use and reduce the performance of your machine. This should take care of your problem. Also could have a bad door seal. Check for any tares in the gasket.
Repair Help & Product Troubleshooting for Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My frigidaire dishwasher leaks from the bottom right of the door. It forms a puddle while running a load of dishes. Looks like the seal is gone underneath the door on the right side. Any idea how to replace this seal? Thanks.


One possible solution to your problem could be as follows... Could have been little regular soap or something put in that made it suds up causing it to leak out of the front and sometimes not to drain all water out. Pouring vegetable oil into the dis ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

My dishwasher, a Whirlpool DWF B10, is not cleaning properly. When the cycle has finished, there is always a block of undissolved dishwasher tablet/powder left behind. My guess is that the seal to the powder door has gone and allowing the tablet to get wet too early and part dissolve before the door opens - is this likely to be right? If so, can I get a replacement seal or do I have to replace the whole powder & rinse aid containers ??


... Whirlpool Dishwashers

Dishwasher leaking. I was supplied a flat seal ring of about 100mm dia., 10mm wide & 1 mm thick for the machine when I bought the house. Water on the floor tells me something underneath is leaking for the first time. The machine is about 10 yr old and in very good order .This seal could be the problem so before I go getting service personel in I'd like to know if replacing this and the door seal are jobs a careful handyman can do ?


I would say you could do it with out a tech.More then likely you can find information on the web on how to do it step by step or hey use this site more then likely one of us has had the same problem. ... Dishwashers

I have a GE Nautilus that is leaking on the right hand side of the door. I can't get a screwdriver short enough to remove it from the counter top to get a better look at it. I am thinking about just replacing the rubber seal before calling in the experts. Any ideas?


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012wertjidsgiu904 ... GE Nautilus 24" Built-in Dishwasher

I have a Maytag DWU8250BAX and the thing leaks like crazy. I just replaced the door gasket, but that is not the problem. When I took a closer look at the door it seems as though the water is getting up and into the door through a space in the bottom of the door. It seems to me like there should be another door seal to fill a gap that sits between the door hinges. If anyone knows if there should be a seal here and then what the part number might be that would be great. Thanks!


There is an airgap under the door..it should spray up and run down the door not spray up under it..look for crack or hole in spray arm..if there is the wrong soap in it it will flood out with lots of bubbles..just have to flush it out. lastly, if you ... Dishwashers

I have a Maytag MDB7600AWB dish washer. I have a door leak, dripping from the right side. I can not see anything that would allow it. It seems like it could be coming from the inside of the door. Also, there is heat and condensation on at the top of the door, above the leak. It could be that steam is coming from the top right and dripping down the door. Could you give me some idea about fixing the problem.


HI,Check for the following troubleshooting steps:Some leaking around-under-from the door on dishwashers can be traced back to a split in the spray arm. If the lower spray arm develops a split in it, the spray arm can turn too ... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

I have a Neff built-in dishwasher and sometimes there is a heavy leakage of water from the front right-hand side. The unit is 3-years old and there is a build up of scale around the rubber seals. The long seal at the bottom of the door seems to have receded slightly behind the metal panel on the inside of the front door. Is the seal easy to replace ?


Hello,\015\012Check the rubber seal in the bottom of the door has not perished or split,also check the bottom spray arm has not split on the ends as this will direct the spray directly onto the door,causing it to leak.\015\012\015\0 ... Neff 24 in. S5443X2 Built-in Dishwasher

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a dishwasher (cdu8000v) and it's leaking. Its leaking around the bottom of the door. It looks like the black seal is has a grove in it from door shutting. Can I replace the seal or is there a different problem. thanks! Toby


... Crosley Dishwashers

Hello all, We have an Ikea Whirlpool DWF 416 that is a couple of years old and has never caused any problems. From today the door has stopped shutting properly. The electronics and internal mechanisms seem to be working fine, since when you turn it on the cycle starts - but only if you hold the door shut. Has maybe a catch gone? Any ideas for fixing a door-shutting problem like this? Thanks in advance! Dave


The catch is no longer working. Contact IKEA for the replacement part. I'm sure it's available through EBAY or something, but probably not guaranteed or as reliable. ... Dishwashers

Kenmore model#587(Frigidaire) leaks under door. New install. Had machine for a year plus before install. took off front panel- can see water squirting past lower door gasket as wash arms rotate. cause is water running down door during wash cycle piles up in the channels molded into the lower left & right side of the wash tub and pushes out the sides of the lower gasket. looks like a design issue- called SEARS, they just want to sell me a new gasket! go figure. any ideas on a fix?


It does sound like an inner door seal ,however If you get upset at Sears and complain they may help you as they say the squeaky hinge gets the oil..And with Sears the more you squeak the better your chances of results ...Good Luck ... Dishwashers

I have a frigidaire dishwasher model FDBC45BAB0. It has a black door (full door, not panel). I would like to either replace entire door panel w/stainless. Or get a stainless panel just for the front. Any ideas? Thanx


Hello! Here is a website that offers a selection of stainless door covers........www.kitchensource.com/kau/frigodw.htmGuru...................saailer ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I don't have a model number right now, but the front door on my Admiral dishwasher is leaking at the bottom. I have changed the gasket inside the door panel at the bottom but it still leaks. This is a rental property and the renters did a job on this dishwasher. I was wondering if they may have pulled another lower gasket off that I didn't know existed. Something like a windshield wiper. The seal I changed was a foam strip 3 x 22 approx. Thanks for your time, Joan


It may not be the door that is leaking if this is an older admiral or whirlpool dishwasher the lever that holds the soap door closed has a little rubber seal that after time will let water in during the wash cycle it the runs down the inside of the d ... Admiral Dishwashers

I have a leak on my Miele G863SCVI Plus on the lower right corner of the door - I think it is the door seal gasket - how do i replace this and is this a difficult task. Do you have the parts?


... Miele 24 in. Incognito G863 SCVi Built-In Dishwasher

I am not happy with the racks in my new Bosch dishwasher! The bottom rack is not right! The silverware basket is in the back right corner and the silverware catches on the seal on door and it is hard to get to. The tongs are two close together and point the wrong way? The upper rack's tongs are also to close together also. I don't seem to be able to get larger dishes in with these tongs in the way. Having never used the mdl 9000359119 Rev B I had no idea. Buying a Bosch ment quality to me


... Bosch Dishwashers

I have a Miele 24 in. G638 Plus Free-standing Dishwasher which is leaking into the pan underneath the machine (and triggering the polystyrene float switch) I am almost certain that the leak is coming from the main pump seal. Is it feasible to replace the seal (it looks like a major job to take the pump assembly apart). I guess Miele labor charges would make the repair not worthwhile Is there a service manual for this machine. I guess I would need it


Hi\015\012\015\012Please check the bellow link to have a detailed view regarding your query…..\015\012http://www.appliance-r ... Miele 24 in. G638 Plus Free-standing Dishwasher

Hi I went away on holiday and my dishwasher AEG 50800 was in perfect order. When I came back after three weeks it does not work. It was not in use while I was away so I don't get how come it is not working now .It does start up but its like the pump is just not kicking in. Ihear water running but the blades dont move and nothing seems to get washed, any ideas. Or is a new expensive pump my only option? My Husband seems to think a seal might have gone. Can a seal go while not in use? Thanks


It's worth looking under the machine. There is an overflow area with a float switch which sometimes fills up and it stops it working ... AEG Dishwashers

Westinghouse SB915WJ is leaking cold water underneath machine. Working fine, just leaking water. Have changed door seal but it is still leaking. Also tried leveling it but this has not helped. Would like to access underneath and see if clamps are on tight but don't know how to access this part of machine.


... Westinghouse Dishwashers

Leaking dishwasher leaks intermittently. I removed the side panels and there is no sign of water in the base of machine. Door seal seams to be intact. What else can I check. Seal that needs replacing? Machine is 18 months old. seams to leak on the right side of the machine. Please advise. many thanks. My dishwasher showed the error code either OE or E1, I think it was more OE. I stuck my hand in the filter in the bottom of the machine and then it was okay but the next time it was used it leake


What sort of soap powder do you use\015\012some soap powders foam a lot in machine causing dishwasher to leak through seals\015\012also check that the machine is square that is the door is closing parallel with cabinet\015\012do no ... Dishwashers

Leaking dishwasher leaks intermittently. I removed the side panels and there is no sign of water in the base of machine. Door seal seams to be intact. What else can I check. Seal that needs replacing? Machine is 18 months old. seams to leak on the right side of the machine. Please advise. many thanks.


There are screws on the inside of the door on a lot of those\015\012try to tighten them down a little sometimes that can cause a leak. ... LG 24 in. LD-12BW5 Free-standing Dishwasher

Powder solenoid I hav e an AEG Favorit 50700 sensorlogic dishwasher. As soon as I switch on, before even selecting a programme, the solenoid to operate the powder dispenser door operates, then stays activated until I remove power. I've taken the door liner off and the PCB looks OK - but I guess whatever powers up this solenoid has gone short circuit. Any idea what it might be or might look like?


Probably the main module ie the pcb you were looking at ... AEG 24 in. Favorit 50730W Free-standing Dishwasher

Hey Everyone! Ok try this one! I have been working on a KUDS25 Kitchenaid Dishwasher. It was leaking like a siv from the bottom. I replaced both top and bottom plastic bearings and also tightend all the screws at the bottom. Leak Gone, I thought. It now has small leaks down both sides. I have since been told by the owner that he took the door apart himself. I pulled out the dishwasher from the cabinet and ran it. I could see the leaks at the top on both sides of the door latch. I cou


Hello davidgalb. You can install a new gasket to seal the door again. That old seal is not flexible any more. That said, for my time and money I recommend a replacement dishwasher, this one has definitely seen better days. Joe ... Dishwashers

I have a Dishlex Global 450 dishwasher and have a faulty seal to replace. The original door seal had a foot on each side and the replacement I received has 45 degree cuts and no foot. Also the bottom seal replacement appears to be a screw-in type where the original was slipped behind a fold in the door. I have been assured by the supplier that I have received the correct replacement parts. Could you confirm the these parts are in fact correct and if they are which way should the seal lip an


Hello Tony. I am as concerned as you are that this is not the correct replacement part. The key to getting the right part is the model number which is on your machine, if you know where to look. Do this, go to this link to properly locate your mod ... Dishwashers

Model # PLD2850RDC2 has a leak at the bottom of the door. i have replaced the gasket in the vent. Had to remove door cover and seal at bottom of door. Had difficulty replacing bottom seal. How do I replace seal correctly? It is still leaking. Could it be something else?


The side baffels are bad. look on each side on the bottom in the corners and that is were their at just pull them out and get new ones ... Dishwashers

Dishwasher won't run. Replaced door latch and timer/selector unit. Into this POS for over 200 bucks right now, with nil result. Any other ideas? Clean light comes on so power is getting through it.


If it's KitchenAid or Whirlpool or Kenmore, and your clean light BLINKS and the heating element inside is ROUND - there is a problem with your control board and the element. There is a kit containing both, for the price of the heating element alone. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1543 seconds