Having problems with your Frigidaire 24 in. PLD2850 Built-in Dishwasher ?

I need to put the lower pieces of my dishwasher back correctly.

\015 I have a Frigidaire dishwasher. I'm not sure the details--we just moved in and I don't have any paperwork, etc. The dishwasher has a stainless look and is pretty simple, in terms of buttons, nobs.\015\012\015\012I was cleaning the bottom because it was pretty nasty from sitting water (no one has lived here for almost 9 months). The lower pieces all came out--what looks like a filter screen, the arm that swings around and a little basket that seems to snap in place--and now I'm not sure how to put them back correctly. I've tried finding a picture of the order of those pieces online, but haven't had any luck. I don't know if they need to snap in place or just kind of sit there or what.\015\012\015\012Any ideas?\015\012\015\012THANKS!!!\015

Answers :

Repair Help & Product Troubleshooting for Frigidaire 24 in. PLD2850 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to put the lower pieces of my dishwasher back correctly.


Try this website:\015\012 ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Hello, we have a Frigidaire dishwasher Model# FDB1250REC2. There was all kinds of junk down in the lower filter area and when I tried to remove the parts they all came out together and then fell apart. I need to see how the parts go back together, because I thought I had them in there correctly, but when I opened up the dishwasher after running it the water sprayer was laying on the heating element. Could you please help me get it back together right? Thank you


I am having the same problem...were you able to fix it? ... Frigidaire Dishwashers

I have a Whirlpool dishwasher DU800CWDB4. Two plastic pieces ended up on the bottom of the dishwasher one day. I have determined that they are the upper 2 pieces of the lower spray arm tower. I can't figure out how to get them to fit back on correctly.


... Whirlpool 24 in. DU800CWD Built-in Dishwasher

Whirlpool dishwasher DU1145XTPQA. I removed the lower arm etc and cleaned debris from my chopper/pump area. went through steps in reverse to reassemble it all BUT when I put the lower spray arm back on and tighten its VERY wobbly...I am not doing something correct in the last few steps...nut, plastic washer, feed tube cap & wash arm...please help


I did the same exact thing, and ended up with the same result, A very wobbly lower spray arm. Despite it wobbling and hitting the feeder tube to the upper spray arm, it works.... somehow.... ... Dishwashers

Remove the lower wash arm (1) by turning the nut (4) clockwise (right) lift the arm off, there is a bearing (3) (small thin plastic washer) under the arm, be sure not to loose it. Lift the tab on the back of the feed tube cap (2) and swing it to the right and lift up, this may need a bit of pressure to release it This is for my Whirlpool dishwasher DU1100XTP. I'm putting it back together and can't remember if the plastic washer goes on top or underneath the feed tube cap. Also how do I remo


This is not a tuff job plastic washer goes on top . and torx screws . you use a proper torx tip for the screw size . ( you can go to sears parts .com and put in model # and see a good break down of the wash arm s and t ... Dishwashers

The maytag dishwasher model mdb7130AWB stoped cleaning correctly so we went from the arm assembly in bottom of dishwasher down to the cutter disc and we found a crack in the housing so i ordered that piece. the new part was designed a little different but we put it all back together the way it came off. but it started and ran maybe 1 minute and stopped. so i have pulled up the diagram and see some problems. in the current diagram. original there was no part 37, 17 19 and 3, alos the crew d


... Maytag MDB7130 Dishwasher

Need a diagram of how to put the lower spray arm witha tower back into the bottom of dishwasher Maytag model WU284


I think you are looking at item 1 in this diagram.\015\012\015\012Hope it helps. Please rate th ... Maytag Dishwashers

It sounded like something was jammed in the bottom of dishwasher. Took it apart, not sure if put it back together correctly because now it is not turning (bottom). Is there a diagram to look at on how to put back together correctly? Whirlpool Quiet Partner II Serial # FP1386450 Model # DU943PWKQO


Go to sears part sales web site adn look at parts breakdown. ... Dishwashers

There are three legs on the underside of the dishwasher. the front two screw in and out the back one does not. we need the dishwasher to be lower so it will slide into under the counter. what do we do? how can we lower the back leg? it is quite high.


... Bosch Dishwashers

We need to remove the AEG Favorit dishwasher from the housing but the back feet need to be adjusted to lower the machine. Which way do we need to turn the front scews to lower the machine. It is not clear whether the screws lower the feet or the machine.


... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

I have a Fisher and Paykel drawer dishwasher and I'm wondering if there's a way to put a panel on it to make it look like and integrated dishwasher. It would need some way of the panel moving to start the dishwasher because the controls are located on the front. I plan on putting it in an Ikea Akurum that is 24" deep. The dishwasher is 22-9/10 deep, so that looks like it would leave some space for the dishwasher to sit back in the cabinet so the door panel could be flush with the cabinet. I'm no


Hmmmm...the first thing that comes to mind is to check out ApplianceArt.com. they have alot of panel options. I'm not sure if they have the integrated ones you are looking for but they have cheap options for everything else. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

I have LG dishwasher for 2 years now. Working perfectly until one day one glass gets broken during washing cycle. Immideatly we get EO error. We check possible reason of error in the manual then decided to try to fix ourself. We open bottom cover and drain outcoming part. Immideatly we discover a piece of glass that was preventing a small plastic piece to rotate. We remove that piece of glass. Put back covers and machine. We connected it back to outlets and run it. All was working again !!! This


In order to fix problem we disconnected dishwasher, put it on one of side, opened bottom cover - the one that is outside of dishwasher. We find out the part that is\015\012connected to the drain horse. We take of 3 screw and open that part too ... LG Dishwashers

MacMarkus, I just got parts for the dishwasher. I put the circ pump in and no water enters the dishwasher. I also see that I didn't put a plastic cover on one of the leads, so I need to pull the dishwasher to do that. How do I know if I've installed the pump correctly?


Hi look to have even an even chance of repair one simply must get a service manual for the unit you are working on. Simply Google the exact make and model, plus the words...... "Your-make-and-model" service manual pdf download (enter)\015\012\0 ... Dishwashers

I have a Bosch SHU8805UC/14 dishwasher. I took the front door panel off to install it better but ended up with two extra pieces that look like either part 935400 Door Guard, or 935526 Support. I cannot seem to find any place on the inside of the door where these pieces would fit. The dishwasher works fine but seems like it got noisier after I put it back together without these two parts. Can you help me locate the proper place for these 2 plastic parts?


Hello, \015\012\015\012Welcome to FixYa.\015\012\015\012I believe the parts you are referring to are likely the blocks in each corner of the outer door panel. These have been a sticking point for many I tech over ... Bosch Dishwashers

Hi, We have a Frigidaire dishwasher machine 1500 series with fully electronic control. It is a new unit, has been installed nearly 4 months ago. The other day, when I went to take the dishes out of it, I notice that the rubber gasket that seals the door had come off somehow. Along with it I saw, sitting on the bottom, two pieces that looked like part of the seal, but I didn't know where they came from. I put the rubber gasket back on, but now the pieces and now the dishwasher will leak when runn


... Frigidaire Dishwashers

Broken fitting The plastic curved piece that attaches the hose to the white fitting on the back of the dishwasher broke, and I need a replacement.  I have been to Home Depot and they don't have anything to fit it, and I was told to go back to the manufacturer for a replacement piece but have looked online and can't find anything that would allow me to order the part.  Help!??


You don't have to change that piece,just tie the hose (drain hose ) to something that is equal height,this prevents siphoning. Please Rate This ! ... Danby 22 in. DDW396 Free-standing Dishwasher

I have a Frigidaire dishwasher and there is not any water coming out of the top wash arm. There is good water pressure coming out of the lower washarm. I pulled out the dishwasher and can see the water going to the top washarm through the tube and it goes up very slowly. I took out the "check ball" below the lower washarm and it worked good. I put the "check ball" back in and ran the machine on "Upper Rack" and it still does not have any water coming out of the upper washarm. It doesn't seem lik


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check that there is no gunk or mold\015\012behind the filter screen and under the cover at the bottom. N ... Frigidaire PLDB998A Built-in Dishwasher

We need to connect it back to the built in wires in the dishwasher. We need to know what colours or wires connect to the flat gold metal plates, there is a black plastic case that slips on and then 3 plates underneath and on the top, but not quite sure if that is correct. Then there is still wires that are loose that need connecting. Part NO. C00059727 Copreci - Merloni 1 160010266 TD02 0008


... Dishwashers

The lower shelf/drawer in the dishwasher has rusting pieces mostly at joins and also has upright pieces breaking off. Also a couple of small pieces have broken off the top shelf/drawer. I need to replace both shelves/drawers. how do i order replacement parts and at what cost. pat


Hi,\015\012\015\012you'd have to start by providing a make and model & serial number. Check out repairclinic.com, amresupply.com or searspartsdirect.com to name a few, but there are many more on-line appliance part vendors if you do a search with you ... Asko D1876 Dishwasher

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

I had a draining problem, clogged line, fixed. Does the small in line rubber valve under the dishwasher in the transition piece to the hose have any real need to go back? and which direction it is cupped slightly. Also are there any assembly instructions? I cant seem to get it back quite right, or a white washer has split. not sure which.


... Whirlpool 24" Built-In Dishwasher - Black-on-Black

I bought a house with a Bosch dishwasher in it and soon found that the top spinner holes are blocked with bits of old labels. I have removed the spinner and separated the concentric tubes but I do not see how to push the debris back along to the inlet. Do I need a power but very small jet to put into the holes along the arm? Would drying it then putting the suction of a vacuum over the inlet hole be useful?


This is very common if the filters are not cleaned regulary if you remove the arms and soak them in hot soapy water for around half an hour this should loosen the debris also tap them on the side of the sink this will remove more stubborn debris ,ref ... Bosch Dishwashers

The upper spray arm on our dishwasher has become detached from the back of the machine, and there is no obvious means of reattaching it. Are there some clips perhaps that have snapped on the part which attaches to the back wall of the d/washer (part number PP-TD20 - it's a 4 by 1 1/2 inch long rectangular shape with rounded ends) or does this piece somehow need to be taken apart (how - i can't see how i might do this?) and the transparent 2nd layer underneath get attached first? Thanks, Sarah.


What exactly the brand / model of your unit.?Let me know.Thanks ... Dishwashers

KitchenAid Dishwasher KUDP01FL: Called repairman to replace balance link kit. Then door extremely stiff to open & heard loud pop when one of the ropes came off the roller. Repairman came back & put rope back on & replaced door seal, then the door won't close & he claims need a new door latch. When he left, door again extremely stiff to open & heard same loud pop when one of the ropes came off the roller. Now he says he can't fix it and to call someone else. I now have three problems: (1) The doo


May have bent door hinges,, need to check all alignment of door, hinges and latches... ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

MY LOWER DISHWASHER DRAWER IS "GRABBING" AS I PULL THE DRAWER OUT. HAVING LOOKED AT IT CLOSER THE PLASTIC LOCKING LATCH AT THE BACK OF THE DISHWASHER(ON THE LEFT HAND SIDE)IS BROKEN.DO YOU HAVE A PART # FOR THIS PIECE AS WELL AS A PICTURE?


You can download the parts manual for the DD603H from fisher and paykel and check which latch you need. The diagrams are given in it.\015\012\015\012 ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1655 seconds