Having problems with your Frigidaire 24 in. PLD2850 Built-in Dishwasher ?

Need more tension on door. added a aftermerket raise panel door kit. added weight to door is about 25 pounds.


Answers :

Are you sure 25 pounds seems like a lot? Anyway take off the bottom panels under the door. UNPLUG FIRST! you will see the springs on each side usually you can adjust them tighter by moving the springs into slots/holes futher back towards the wall. If this won't work on your model, take a spring off and go to your local hardware store and buy new springs that are shorter or have more tension.
Repair Help & Product Troubleshooting for Frigidaire 24 in. PLD2850 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need more tension on door. added a aftermerket raise panel door kit. added weight to door is about 25 pounds.


Are you sure 25 pounds seems like a lot? Anyway take off the bottom panels under the door. UNPLUG FIRST! you will see the springs on each side usually you can adjust them tighter by moving the springs into slots/holes futher back towards the wall. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

I have a Lady Kenmore(model 665-1596581) that needs replacing. Is there a current DW model that will accept the wood panels from the Lady Kenmore? Where can I find the dimensions of the current cabinet door kit for the DU 1055 XTS to see if the old oak panels will fit the new dishwasher.


... Whirlpool DU1055XTS Built-in Dishwasher

Need stronger Door Springs, to able wood door panel


The best suggestion I could give you is contact either Sears or Bosch and ask for recommendations. You will require the proper springs designed for dishwashers. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a SHU8805UC/14 BOSCH DW and need to replace the inner door panel. I ordered the part, but there are no instructions on how to replace the door panel. I want to make sure I do it correctly, so


Go on line with Bosh company and look up dishwashers giving your model. Request technical assistance to install the panel... ... Bosch Dishwashers

Door panel The panel on the door has rusted after 3 years. I need to find a replacement panel. Where can I buy/order one. I live in Gansbaai along the coast about 180km from Cape Town. The closest town is Hermanus. I am a good handyman and am able to fit the panel myself. This is urgent as my wife can not use her hands to wash dishes.


You will either need to have one made locally to match, or order one from the maker. try on line. you will need the model number and serial number to make certain that you get the right part.and in the meantime, you might need to do the dishes ... Indesit 24 in. D61 Free-standing Dishwasher

Hello, I purchased a Kitchen Aid Architect II series KUDSO3FTPA3 ~ two years ago. It is deigned so you can put your own panel on it. Duw to a design issue with my cabinets I was not able to add my own panel and wanted to purchase the stainless panel to cover the front of the dishwasher. Kitchen aid was no help, they sold me a panel that would not fit and then would not take it back! Then they said I would need to replace the entire door for $389.00! I need to know if there is a stainless


There is a MUCH better way! go to www.applianceart.com, these guys have tons of panel options including stainless and fax stainless that was featured on HGTV and the Today Show. www.applianceart.com (Appliance Art) ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Whirlpool DU980QPDQ3: As per FixYa solution, I was successful in removing the inner panel of my dishwasher door in order to clean it. Since reinstalling the inner door panel, including the cover and drawbar for the detergent dispenser latch, the dispenser door will not open during the wash cycle. I have checked everything and cannot figure out what is wrong. I have only been able to locate disassembly instructions, but not the detailed assembly instructions that I need to get the dispenser do


Here are a few videos that may help\015\012Click on the link http://www.youtube.com/watch?v=MDideDjjuEU\015\012\015\012Click on the link ... Dishwashers

WHAT ARE THE THERMAL FUSE SPECIFICATIONS FOR KENMORE ELITE MODEL 66513122K701SERIAL NUMBER FY1211868 AND WHAT IS THE PART NUMBER FOR A THERMAL FUSE KIT? WE HAVE HAD TWO FUSES BLOW AND THERE DAMAGE TO THE WIRING ON THE LEFT HAND SIDE OF THE CONTROL PANEL THAT CONNECTS O THE SWITCH. THEIR IS DISCOLORATION ON THE PARTS AND WIRING. WE HAVE SEEN EXPERTS STATE THAT IN ORDER TO CORRECT OUR ISSUE WITH THE FUSE BURNING OUT WE NEED A THERMAL FUSE KIT AND WE NEED THE SWITCH AND THE WIRING THAT CONNECTS TO


Http://appliancejunk.com/ge/dishwasher/31-9137.pdf\015\012\015\012A ... Dishwashers

DOOR TENSION The door is too "savage" the tension need adjusting but how there are no obvious screw's available or do we have to remove the dishwasher from its fixed position to get at screws on the side that is if they are there?


Open the dishwasher and look at the top of the chassis, where the door catch is. You'll see 2 screws with hexagonal heads, one on either side of the catch. Turning these screws will apply or reduce tension on a wire liked to a spring on ... Indesit 23 in. DV62 IX Built-in Dishwasher

I have a KUDM22 dishwasher. I need to replace the soap dispenser. Which screws release the inner panel of the door; the 10 screws around the moulding or the 6 screws on the inner door panel ?/


... KitchenAid 24 in. KUDM25SH Built-in Dishwasher

I need a new front panel and door seal for a customers dishwasher. It is a fisher and paykel Nautilas The opperating instructions say it is a model 920 . I can not read the model No from inside door as it has been cleaned off the sticker. The panel is black and has the led display on the right hand side


Check out www.applianceart.com ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

KitchenAid Dishwasher KUDP01FL: Called repairman to replace balance link kit. Then door extremely stiff to open & heard loud pop when one of the ropes came off the roller. Repairman came back & put rope back on & replaced door seal, then the door won't close & he claims need a new door latch. When he left, door again extremely stiff to open & heard same loud pop when one of the ropes came off the roller. Now he says he can't fix it and to call someone else. I now have three problems: (1) The doo


May have bent door hinges,, need to check all alignment of door, hinges and latches... ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I need the diagram for the door pulley system so I can make sure I am hooking it up right. The original door chord/pulley assembly broke. I ordered new parts, Now I want to make sure I am putting it back together the right way. The edge of the screw- on floor panel is pushing the plastic hook off of the door hook when you shut the dishwasher door.


... KitchenAid Dishwashers

Need to remove decorative door panel


I am not sure how to remove the panel on yours but I know of a site that offers an easy solution to change the appearance of your appliances.\015\012www.applianceart.com ... Bosch SHV68 Built-in Dishwasher

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

Cycle interupted until pressure applied to door, near control panel. Fault is intermittent. Sometimes I need to lean a chair against it to keep it going. Door clicks shut nicely and does not leak. Cycle always starts but often will not complete without a thump. Is pressure inside bowing the door and activating a safety switch?


Problem on the safety switch\015\0121)try to adjust the safety switch to contact properly with the door.\015\0122)any screw is there on switch means loosen the screw &adjust to contact with door. ... Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher

I have a Fisher and Paykel drawer dishwasher and I'm wondering if there's a way to put a panel on it to make it look like and integrated dishwasher. It would need some way of the panel moving to start the dishwasher because the controls are located on the front. I plan on putting it in an Ikea Akurum that is 24" deep. The dishwasher is 22-9/10 deep, so that looks like it would leave some space for the dishwasher to sit back in the cabinet so the door panel could be flush with the cabinet. I'm no


Hmmmm...the first thing that comes to mind is to check out ApplianceArt.com. they have alot of panel options. I'm not sure if they have the integrated ones you are looking for but they have cheap options for everything else. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Need stainless steel door panel for model


... Whirlpool Dishwashers

I need a new door, and a new front panel. Where in


There is an easier way - www.applianceart.com has standard panels and a ton of options including colors and stainless steel. ... Danby DDW496W Free-Standing Dishwasher

My Bosch dishwasher Model #SMU4056UC will not start but it will make a certain noise and I think it may be the timer but I don't want to be wrong and pay for a part I dont need. I also need instructions on how to take off the door panel


... Bosch 24 in. SMU40 Built-in Dishwasher

Need to replace door latch. Do I access it by removing all the screws on the inside door panel? or something else? thanks


Only the top half screw's would be enough, the pannel should popout then... ... KitchenAid KUDR01TJ Dishwasher

I have an Optima series G1470 or G2470 dishwasher with a heavy panel on the front to match the kitchen cabinets. I want to tighten the door spring so I can open it more gently. House guests tend to let go of the door part way down and it bangs open the rest of the way. Also, I have not put salt in. Do I need to in Wisconsin? If so, what kind of salt do I use? Thanks, MJ


About the use of salt depending on water hardness, there is a very good explanation on page 11 ... Miele Premier-Plus Built-in Dishwasher

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

My KitchenAid dishwasher's door tension broke. The door falls to the floor now. The model # is KUDIO1FLSS6. What part number do I need and can I fix this myself?


... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1319 seconds