Having problems with your Frigidaire 24 in. PLD2850 Built-in Dishwasher ?

Frigidaire fghd2433 control interface problem: Only selection possible is "Heavy wash" all other buttons on control interface are dead with the exception of start. Child lock not the problem here. This was installed 2 days ago.


Answers :

Repair Help & Product Troubleshooting for Frigidaire 24 in. PLD2850 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Frigidaire fghd2433 control interface problem: Only selection possible is "Heavy wash" all other buttons on control interface are dead with the exception of start. Child lock not the problem here. This was installed 2 days ago.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

Dish washer 665.13592K600. Will not start. When door is closed you can hear the click of the latch then a relay on the control board. All buttons work except delay and start. You can push the cancel and drain button and the pump will activate. The start and delay buttons have no effect. Not sure if I have a control board or panel problem.


... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

Have a 4 year old Kenmore Dishwasher Model # 74382. No problems at all until last week I went to start it and it would not turn on. Lights on the control panel were on with exception to the start light. I opened and shut the door to make sure it clicked and pressed the start button again and nothing. I tapped around the panel with the side of my fist and pressed it again and it began working. Well today different story I went to start it and it did the same thing. I tapped all over front of the


The problem is more likely the door switch is failing or out of adjustment/loose. You will need to remove the door panel. This is easy to do. There is a video at ... Kenmore 24 in. 74382 / 74384 / 74389 Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

My dishwasher won't start (Series 300 purchased 14 months ago). The following lights are on: light wash,hi temp wash,sanitize, locked and the start /resume light is flashing put goes out when pushed and the machine does not start when closed. there has been an on going problem with the regular wash light not coming on when pushed.


Hi\015\012\015\012It may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting t ... Maytag 24 in. MDB9750AW Dishwasher

I have a Triton Aspirante Topaz shower which I purchased 2 years ago. Just recently it has started to give me a problem. With the temperature control set normally to 43 the shower goes through its pre


... Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

I have a kenmore dishwasher model #655.1374 or 655.1384 which is only about a year old. I am having a problem with the controls. It will not allow me to use smartwash. The only control that can be used is quick rinse. I reset it by pushing Sani rinse and heated dry. All the lights come on and it seems to do a test. But after that still the same thing except if I push start resume it goes to normal wash which stays on a long time and periodically the cancel drain light comes on as well as the 4


... Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

New SHE4AM16UC, professionally installed eight months ago. Worked fine with very light usage until now. Dishwasher starts normally but stops and signals "clean" after less than five minutes on any cycle. One inch of water in bottom that (I think) drains when a new cycle starts. Soap tablets are not ejected from compartment. Bosch authorized repairman says he now has two client dishwashers with identical symptoms and is asking Bosch support for ideas (he's changed pump, control unit, and float sw


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats.\015\012When the dishwasher doesn't sense a water t ... Bosch SHE4AM16UC 24 in. Built-in Dishwasher

The lights on control panel are locked/ lit up - dishwasher doesn't work. tried to disconnect and start - to no avail. Had problem previously and repairman said it was the control board/panel


You need to turn off the control lock option by pressing the heated\\dry pad for 3 seconds ... Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher

My Kenmore Diswasher (Mod # 665.17842400) has crapped out again. Towards the end of a cycle, the power seems to have been lost. There is now water in the bottom, and the user interface won't come on. 2 months ago I replaced the user interface and the magical board it connects to to solve a start button problem. I checked the power coming to the washer and it is live.


There is a thermal fuse on the control board. It protects in a overheating problem or sometimes when there are to many appliances on the same circuit that creates a high amp draw, that melts the fuse not actually blowing it like a short. Check your d ... Kenmore Dishwashers

I have a whirlpool DU943PWKQU, first about 6 months ago all the push buttons except light wash stopped working. Now this week it started giving me problems starting all together at first I resolved by unplugging and replugging the electrical cord but this is no longer working. Can you tell if something can be done?


It seems to be the program controller and you will have to get this checked. Remove the power off for some time and reset it back . If the programs are not responding then you will need to check from the power cord to the control panel to see if this ... Whirlpool Dishwashers

Hi, I have had a few issues with my ST663 machine. The current problem: the rinse cycle light keeps flashing and it doesn't start when you shut the door. I have tried holding down the right button but it beeps twice and nothing happens? Also tried holding both buttons down for a while and still no success. I got a new electrical board installed not that long ago so not very happy hoping it not a big issue. Do you have any other things that I could maybe do?


HiIf you have already tried to reset the unit by pressing the High Temp wash-heated dry button for 3-4 times in sequence then the problem is either with the door switch or the keypad itself that has gone bad and should be replaced. Hope t ... Dishwashers

I have an LDS5811 and I just started getting an IE error. The manual says its a water inlet problem. I have not moved the unit since installing 3 years ago and have not disturbed the water supply. I checked the inlet tube and all appears OK. Any other suggestions?


I have had this error occur often due to faulty flow meter -remove left hand side panel, there is a large plastic component with three wires(red, white, black), these wires go up and connect onto main control board. Check these three thin wires for b ... LG Dishwashers

GE Dishwasheer installed 09/04/2007. Model #GLD6700N00WW Serial # LM788127B It stopped in the middle of a cycle. Showed 81 minutes left and lights showing on Added Heat. Without realizing what I was pushing I turned the child control button on. It will not start or do anything now. Help!


Hi gmrnelson,Huuum here again.You forgot to give me a solved rating before you signed off!Thank You in advance! ... Dishwashers

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

Our Asko dishwasher no longer cleans the top shelf of dishes properly. Fine white and black grit is left on the dishes after every wash, and if there is any food residue on the dishes it does not come off. In addition, food residue that was not on the dishes to start with is being thrown up onto the top shelf and doesn't clean off the dishes. The control unit was replaced 2 months ago at vast expense, and this problem only arose following the repair. The only suggestion from Asko to fix the new


The problem is most likely that there is still water residue at the bottom of your machine. If the machine is not fully drained it picks up some of the residue and sprays that onto the dishes during the final rinse, leaving an unhealthy and un ... Asko 24 in. D3350 Dishwasher

Hello expert, We are having a new kitchen floor laid and the contractor moved the Whirlpool dishwasher out to lay the floor under. Since it was replaced into it's normal under the counter spot, green "clean" light flashing in succession with a brief stop then starts again. Not really bothered as long as it worked, but of course it doesn't work - What do you suggest?? P.S. Had a problem app. 2 years ago when someone backed into the control panel, also ceased working and repairman charged ex


Someone grabbed the control panel and knocked it around or flexed it whist moving it in and out of your counter.\015\012\015\012Either the PCB board behind the little buttons flexed and cracked, or the ribbon cable that connects the PCB b ... Dishwashers

Samsung DMR57 We bought a Samsung in June and have been trying to get it to work properly ever since. It is very quite which is great, but like the other person wrote the thing keeps coming on even when the child lock is on. We have had a repair man out twice but it they haven't fixed it yet. The dishwasher is right under the counter we use to prepare food so we often rub up against the controls. The power comes and and it starts the machine on whatever cycle it used last, or rinses the dishes.


... Samsung 24 in. DB5710DT Stainless Steel Built-in Dishwasher

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

The control lock light goes on as soon as I press the cycle to start the dishwasher. The dishwasher does not start, presumably because the control lock stays on. I do not know how to disable the control lock function. Pushing and holding the button for 3 seconds does not disable it.


Hello &\015\012Welcome to FixYa\015\012\015\012To unlock the\015\012controls press and hold the HEATED DRY button for 20seconds. If the problme\015\012returns then only option is touch pad replacement. Please get back t ... Maytag Dishwasher

Throttle problems Homelite pressure washer model UT80709A. bought it 10 months ago with no problems and stored it for last 9 months. Before doing so, drained gas, oil. Brought out of storage a few days ago, filled with fresh gas, oil, cleaned air filter. Starts great first try but after about 30 seconds the throttle starts visibly revving the motor a litlle at first then gradually faster and faster until it seems to flood and die. Then you cant start for about an hour and its the same story. Hav


... Homelite Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1594 seconds