Having problems with your Frigidaire Dishwashers ?

Dishwasher FDB4315LFC0 Error code ER uo Second time it has happened. First time, a repairman came and said I needed a new "vent assembly", but I asked if he could "un stick it," so he took it apart and fiddled with it, and it worked for about a month. Now the error code is back, and he warned that if it came back, I should have it replaced. I've only had this NEW machine 10 months -- this shouldn't happen, right? Any suggestions? Thanks.


Answers :

Who's to say what should or shouldn't happen?
Sounds like you need a new vent assembly.
Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher FDB4315LFC0 Error code ER uo Second time it has happened. First time, a repairman came and said I needed a new "vent assembly", but I asked if he could "un stick it," so he took it apart and fiddled with it, and it worked for about a month. Now the error code is back, and he warned that if it came back, I should have it replaced. I've only had this NEW machine 10 months -- this shouldn't happen, right? Any suggestions? Thanks.


Who's to say what should or shouldn't happen?Sounds like you need a new vent assembly. ... Frigidaire Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

We have and older Jackson model 10 AB at church, used 10 to 20 times per year. The pump motor quit this summer and was replaced by a local appliance service company. About $700 job. Upon using it recently, the first time since the new pump was installed, the RINSE cycle seems very anemic, that is, low volume and low spin rate. The dishes were not completely rinsed. Temperature was correct, 185 degrees. The service person came back to look with no improvement and now the Heaters will not co


Sounds like a wiring problem but it is controled by a thermo to make sure you get to the proper tempt . so ck the connections and mke sure the thermo is good . . and the element is good . ..hope this helps mm . ... Jackson 10A Free-standing Dishwasher

My dishwasher recently started leaving a white, chalky residue on all the dishes. It wasn't gradual at all. One day everything was fine and all the dishes clean and the next they were covered in nasty residue. We've ruled out any issues with soap, rinse agents and hard water. A appliance repair guy came out and said the float was "tampered" with and said that he fixed it. He said that if the problem came back we need to order a new float assembly kit. My husband has looked at it several times an


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Whirlpool Dishwashers

I had a black out and the dishwasher was running at the time. The dishwasher emptied out all over the floor. when the power came back on the dishwasher was flashing an error code 4. I rang Whirlpool for assistance and they said it was over full but it was totally empty. We turned the dishwasher off at the wall hoping it would reset but it is still saying error code 4. Can you suggest something else we can do?


The trouble looks to be little confusing. Whenever the power failsduring mid cycle this happens. Try running the balance cycle. Since you say the water is fully drained, try adding water manually tothe wash chamber to certain ... Whirlpool Dishwashers

There's a foul smell coming from the dishwasher evert time I open it. Doing a wash does not solve this. I'v had this since it was new, months ago, and have had the installer look at it, said it wasn't his problem. Had a tech. come in and said it wasn't his problem. I've owned many dishwashers and never has it had a foul smell. Last fall I went to Nova Scotia, ran the dishwasher before I left, came back in two weeks and noticied water was still in the bottom of the dishwasher-it didn't drain all


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

Ther's a foul smell coming from the dishwasher evert time I open it. Doing a wash does not solve this. I'v had this since it was new, months ago, and have had the installer look at it, said it wasn't his problem. Had a tech. come in and said it wasn't his problem. I've owned many dishwashers and never has it had a foul smell. Last fall I went to Nova Scotia, ran the dishwasher before I left, came back in two weeks and noticied water was still in the bottom of the dishwasher-it didn't drain all t


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

I'm working with a kitchenaid D/W model N0. KUDS01FKSS1: I repired a broken wire that shorted out near the main board, after repairing the wire the cycle selector board "light wash cycle" was not working, after the customer used the D/W the "clean light starting flashing 7 times then pauses repeately, after instaling the selector board, I entered the diagnoptics code all lights came on and then I cancelled, the D/W started working, when the cycle finish the light will come back and D/W will no


... KitchenAid Dishwashers

KitchenAid Dishwasher KUDP01FL: Called repairman to replace balance link kit. Then door extremely stiff to open & heard loud pop when one of the ropes came off the roller. Repairman came back & put rope back on & replaced door seal, then the door won't close & he claims need a new door latch. When he left, door again extremely stiff to open & heard same loud pop when one of the ropes came off the roller. Now he says he can't fix it and to call someone else. I now have three problems: (1) The doo


May have bent door hinges,, need to check all alignment of door, hinges and latches... ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a Dishlex Global 500 dishwasher (DX500lWW*b). Woke up the other night to find water all over my kitchen floor. The hot water hose connector to the hot water tap split (bursted). The dishwater was not in operation at the time but I can only assume when the hose bursted the dishwater came on to alert me? the code on the dishwater is displaying ''oF'' - which means Incorrect fill level of fill time. I have consequently had the hose connector repaired but the display still has the code ''oF''


I found this\015\012\015\012"Hi - answer I was given by Electrolux Help was: pull machine out from under bench onto old towel, tip GENTLY onto left hand side (your left as you face the front of the machine) after it has drained, stand up ... Dishwashers

I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support


... Bosch Dishwashers

My Whirlpool wdf530payw dishwasher is not draining. I ran the service diagnostics using the control panel, and the code that came back was Function code 8, and Error code 2 "Drain Motor Electrical Problem". The possible causes listed are: a. Loose Connection in drain motor circuit, and/or open drain motor winding. b. Open Fuse on control to drain motor c. Faulty drain motor drive circuit on the control When I hit the "Cancel/Drain" button there's an faint buzzing sound for about 2 minut


... Whirlpool Dishwasher. Front Control Dishwasher in White WDF530PAYW

I recently had the e4 error code on my new world dw60 dishwasher. I have since opened it up and replaced the heater element, which appears to have resolved that issue. However, in the process of doing this I incorrectly installed the flood switch back into place, meaning that it was in its closed position (i.e. the position it would be when activated by a flooded base) when I went to turn the dishwasher back on. I have since opened it back up and correctly installed the flood switch, but I ca


... Stoves 27 in. DW60 Built-in Dishwasher

Have a new GE Profile dishwasher. The LED time display started at 62 the first time we used the machine. It keeps going up and is now at 108. Is it broken and how do we reset the time back to something more reasonable. We typically pre-wash the dishes anyway and it shouldn't have to take that long to clean....thanks!


Have you tried to turn the mains power to dishwasher off and back on again.\015\012\015\012It also possible the inlet water temperature is not at the recommended temperature so it is compensating for heating it to the desired temperature. ... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

I bought a used 7 1/2 year old fisher paykel dd603 for my tenant, it worked fine the first time. second time she got F1 code on both drawers. water was in lower pan, we sopped it up and dried it out. also drawer was not seating level but was lower on left side, and insulation had fallen off left wall. all now corrected. but now the top drawer leaks onto floor on left side. it did not leak before repairman came out, we checked thoroughly. repairman says top lid not seating properly and i need ne


I have the same model F&P and just experienced similar problems. My top drawer was leaking due to that "not important" thin white tube. It really sounds like you called a general appliance guy and not a trained F&P repairman. The guy who fixe ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Hi In the middle of a wash cycle, my dishwasher tripped the circuit breaker on the wall. I diagnosed this by unpluggin dishwasher, plugging in a different appliance and switching circuit breaker back on. new appliance worked OK. When dishwasher had cooled, I tried it again on same circuit (which I knew was working properly). The lights came on for about three seconds, and then the circuit breaker cut back in again, so I knew it was the dishwasher that was causing the problem. Is there anyt


Ck the connections where the cord hooks to the wiring harness. look for hot or shorted wiring . also ck the contro panel for the same . generaly if you have a power draw like you are saying then you can see t ... Dishwashers

Good morning. I have a KitchenAid KUDM01TJ with a constantly flashing "Rinse" light. when I hit the "Cancel" button, it too flashes in the same time with the Rinse light. I left the machine alone, came back a few days later and saw that the issue had resolved itself - but I didn't use the machine. A few days later, the "Rinse" light was flashing again and naturally, I hit "Cancel" to see if the same thing happened and it did. This time the lamps are still flashing. I read through the other repo


No its not the problem of button secquence.its the problem of keypad circuit this is creating this problem.as the circuit is getting overheated and it stops working.the key pad sometimes functions and sometiomes doesnot.in this case the key pad circ ... Dishwashers

F2 Code Hey, I have a single drawer built in Fisher & Paykel dish drawer and today I pulled the spray arm, filter and large metal screen out to clean them as we have been starting to get a bit of stuff left behind after washing lately. That was all good After putting it all back in though I went to use the dishwasher and it stopped and came up with an F2 fault, I thought I may not have put the bits back in properly so pulled them out again and noticed that on the rotor that connects the motor to


Fault F2 means the rotor is not rotating. If you say some of the vanes have broken off, they could have been jamming it. This should spin freely with minimal force when installed correctly. If you removed the rotor itself, you do ned to take care whe ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I turned on the dishwasher tonight and noticed nothing was happening, but I was getting a clicking sound. I moved the dial back to off and started over. Some water went in, but then nothing happened again. I clicked forward one click at a time. Sometimes water came in. THEN WATER STARTED LEAKING OUT. I clicked back to off. After water stopped leaking, I opened the door. There is still water in the bottom. What do I do???


Hi \015\012\015\012Thanks for using FixYa. As the water is not draining and clicking is\015\012coming from the bottom so the issue seems to be with the drain pump solenoid. Usually, these issues are related\015\012to ... Kenmore Dishwashers

G851 SC Plus started to trip GFI plug. Called Miele and they said there was nothing wrong with the dishwasher and the GFI was faulty. Unplugged from GFI and plugged into regular plug and it worked for a few days. Eventually stopped running. How wrong Miele was, it had everything to do with the dishwasher and not the GFI. It was only warning me a problem was coming. Appliance man came out, noticed water in bottom pan and order new pump, said seal probably gone. Came back, replaced the pump, put d


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on I bought mine new off the internet and it's been running great for about 2 months. Now I can't get it to drain and E2 shows, I can't get my money back because I've had it more than 30 days, if the solution is a pump, I'm tossing it and getting a good one from


E2 is a hose issue. There is either a kink in the hose, the hose is too high to drain or the pump is faulty.1-800-26 DANBY ... Danby DDW497W 22 in. Countertop Dishwasher

Our dishwasher won't start (model number 665.16049401). We had a similar problem last summer and a repairman came and fixed it. The problem was that the water level had gotten too low and so the machine locked itself off. This made sense as, at the time, I remembered filling the pool, running laundry and someone taking a shower all at the same time that I turned the dishwasher on. I am guessing this is the same thing that has happened now. The repairman put in a code and the machine worked. Can


Hello,\015\012\015\012ahhhh, you're taking about the reset sequence.\015\012okey dokie :)\015\012\015\012Here it is:\015\012Push the NORMAL WASH then HEATED DRY buttons in that sequence two to three t ... Kenmore Dishwashers

Cycle time Just moved in, started the Bosch dishwashe that appears to be less than two years old, left for one-hour and came back to find the wash cycle still going; hasn't cycled in thirty minutes since I've returned. Is this normal? What is the standard cycle time?


Yes its normal.bosch dishwashers use very little water and energy but,the cycles need to be longer to get the dishes clean. its perfectly OK.(ps use cascade powder if you can) ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1199 seconds