Having problems with your Frigidaire Dishwashers ?

Replaced the soloniod, still no water goes through. hums but nothing happens


Answers :

Be gentle with me, but are you certain that the under-sink, hot water valve is open? I really have made that mistake. \015\012
\015\012(Just like when I connected a new dishwasher to the new garbage disposal, but did not remove the knock out where it connects.)
Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replaced the soloniod, still no water goes through. hums but nothing happens


Be gentle with me, but are you certain that the under-sink, hot water valve is open? I really have made that mistake. \015\012\015\012(Just like when I connected a new dishwasher to the new garbage disposal, but did ... Frigidaire Dishwashers

My 12 yr old KitchenAid -Sculptura-Model KUDR24SE starts to fills with water and then does nothing else. It will eventually go through the cycles on the panel, but nothing is happening inside. End result is still dirty dishes with water sitting in the bottom that has to be baled out. Cups on top rack don't have any water on the indentations, so it's obvious that the thing filled with water and that's it. I had the motor replaced (supposedly with a new) one 2 years ago so I find it hard to bel


... Dishwashers

I have a Defy Dishwasher DW-12. I push the start button and it makes a sound as if to start and no water comes in - it just hums and the water is on. It has been working fine. - but last night i was woken up with it still buzzing after 5 hours! and nothing happening


... Dishwashers

My Samsung DMR77LHS dishwasher has lost power completely near the end of a cycle. About an inch of water remains. I have power to the unit. I checked the 15 amp fuse in the unit - it had blown. I replaced it, but still no luck. The fuse is not blowing, but there is no power to panel. Nothing happens when you hit the power button - no lights or anything. Unit acts as if ther is no power at all. I have seen similar posts. Any thoughts?


Hi, whenever a fuse of that magnitude, or any fuse really, Blows, you should never just replace it, as to have any device, blow a fuse, trip a breaker, requires a major fault, they do NOT blow spontaneously ever. So you have had a major short circu ... Samsung DMR77LHS Tall Tub Dishwasher

I turned on the dishwasher tonight and noticed nothing was happening, but I was getting a clicking sound. I moved the dial back to off and started over. Some water went in, but then nothing happened again. I clicked forward one click at a time. Sometimes water came in. THEN WATER STARTED LEAKING OUT. I clicked back to off. After water stopped leaking, I opened the door. There is still water in the bottom. What do I do???


Hi \015\012\015\012Thanks for using FixYa. As the water is not draining and clicking is\015\012coming from the bottom so the issue seems to be with the drain pump solenoid. Usually, these issues are related\015\012to ... Kenmore Dishwashers

Inlet Valve keeps stopping and starting, takes a bit of water then stops take a bit more then stops, on off on off for about 10 mins until its taken enough water to srta the cycle , have replaced the Inlet Valve still happening and water flow meter with pcb still happening Any suggestions? It a DWLT65


What about the overflow valve? It could be sticking ... Beko Dishwashers

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

When I hit the start button on my dishwasher nothing happens. It still "finishes" the cycle but nothing ever cuts on. It doesnt fill with water and the sump pump never engages to drain the water that's not there. Any ideas? I know the inlet water pump works, I've detached it and connected it with a pigtail to an outlet.


Replace the main control board ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Help i just replaced the module on our icemaker, and i ran through one cylce but nothing has happended on water was called by it. i left it on but still nothing, and its been about 2.5 hours. water is on and the water dispencer works.


The water valve has two sides..one for ice and one for water...i take a two terminal jumper and apply 110 volts right to the coil..if water does not flow..its bad..the icemaker on has the small tube going up the back wall to i/m ... Whirlpool W10190935 WHIRLPOOL W10190935 ICEMAKER CONTROL MODULE AND MOTOR A

I have just moved into a new house with an Asko Dishwasher. It is not working. I program it, the icon for the cycle I have chosen lights up in red, I press start, that lights up in red, the water runs in for about 30 seconds and then nothing more happens. This happens on every wash cycle that I attempt to use. It does not appear to be on time delay as that icon does not light up. Also I have left it for a number of hours after I have tried to start it and still nothing happens. I would appreciat


... Asko Dishwashers

When i turn my Viking dishwasher on the motor starts to run but no water comes out. It was humming along for several hours before i realized that nothing was really happening. I turned it of and then tried again but the same thing happened. It sound like a motor and/or pump working but no water enters the chamber. Thanks, Jonathan


It sounds like the Water Supply Solenoid is bad. I would change that and let all of us know what happens. ... Dishwashers

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

I have a KitchenAid Dishwasher KUDIO1iLBS2 and none of the lights come on and if I press any of the buttons nothing happens. The unit is getting power to it as I shocked myself. I did ordered and replaced the control board and still nothing is happening. Any suggestions or ideas? Is there a reset button or is there a possible fuse that is out that would make the lights not come on? Please help.


... KitchenAid Dishwashers

I am an electrician, and have been called to repair a faulty Hobart comercial dishwasher. I didn't note the model number, but it is the same shape as the one pictured. The problem is that nothing happens when the lid is closed, like it has a faulty switch or sensor. When I got to site, the dishwasher had been drained, and would not automatically refill. I filled it with a bucket, it heated the water to the correct temp, but still nothing happens when the top is closed, and I have to have it


Hello Pat. Here is the link to the hobart line of kitchen equipment. It has all of their manuals as free downloads. If you have a laptop and internet access you can get the correct manual once you know the model number. Based upon what you said t ... Hobart AM15-5 Dishwasher

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

My dishwasher (Optima G2420) had an error F13 for sometime. By turning it off and restarding it would work. But now drain/intake light flashes and nothing is happening. We have checked the triple filter, the filter where water comes in ect. It drains the water but it appears that it cannot take water in. There is a white unit that the intake water goes in and I think that might be the proble.


... Miele Optima G2420SCi Stainless Steel Builtin Dishwasher

The start timer control cycles but nothing happens. The motor seems to gurgle while attempting to fill with water - but no water comes through. We have had this problem before and the repair person replaced the timer control board. Could this be the same problem reoccuring? I have also tapped and cleaned the water float as described by GE website.


I bought a new one and installed it myself. hardest part of installing was taking the old unit out. I compared the cost of a second repair of a 10 year old dishwasher vs. purchasing a new one. We also checked the pump and solenoid to find problems th ... GE Nautilus 24" Built-in Dishwasher

Won't drain dishwasher goes through all cycles like normal but when it's finished there is still water in bottom, tried to cancel cycle but water stays. I cleaned all the water out and try it again same thing happened. I cleaned the filter so i don't know what else to do!


Make sure the garbage disposal is clear so the water can exit. After that, you may have something caught in the drain hose or check valve. It would require removing the bottom kick plate to gain access to check. ... Kenmore 24 in. 15689 Built-in Dishwasher

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


Hi There,\015\012\015\012Your description seems to indicate a fault in the water heating circuit or components. This is often the reason for a wash cycle not finishing and draining. As the machine will drain when you lift the overflow lev ... Dishwashers

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


... Dishwashers

Bosch aquasensor I have just had a plumber install a second hand dishwasher as above, he left after he heard the water coming in, two mins after it stopped and nothing else happened bar the time still going, he has plumbed it into the cold water, is this correct or am I doing something wrong. Please help, thanks


No it should be plumbed into the hot side... it will not wash untill the water is hot enough ... ... Bosch 24 in. SHU43 Built-in Dishwasher

Stops part way through programme water still in machine. Now no power to machine. Problem happened yesterday - cleaned filter and pump - power came back. Programme started but then stopped. No power - nothing happens.


Either there is a bad capacitor in the control panel, or the power supply has a faulty capacitor. You will have to get a multi-tester and test each component for resistance and current ... Dishwashers

I have a Asko D3122 dishwasher. When I switch in on it seems to drain the water out bu when it comes to put water back in it just shuts off the L7 light is still on but there is nothing happening.


... Asko D3122XLSS Stainless Steel Dishwasher

There is a pool at the bootom of my dishwasher when the wash cycle is completed. When doing "Rinse Only", I could hear something come on immediately following the rinse but nothing seemed to happen. I pulled the Dishwasher out and the drain tube is set up so that it immediately goes upward a few feet before it eventualy goes back down to the drain. I noticed that there is water in the tube right next to the Dishwasher before it makes that climb. I'm wondering what all this means...


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012 ... GE GLD5800L Dishwasher

This is the 2nd time I've had problems with my dish drawer. After I cleaned the filter and replaced it, I had standing water on the bottom of the drawer. The last time this happened, I had someone come to repair it - ended up it was me. I didn't put it together properly. This time I did the same thing I was told to do. I still have the standing water. What should I do. By the way, the coils are not kinked in the back either. Can you please give me some advice? Please respond to me at F


Unfortunately I have to respond to you through this post per policy of fixya.com. This s to ensure we have a visibility on the quality of the solution and also allow other consultants to help if necessary.\015\012\015\012Water standing a ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1810 seconds