Having problems with your Frigidaire Dishwashers ?

Suddenly, an error message appeared on the display of my Frigidaire gallery series dishwasher, model number GLD3450RDS0. On advice from Electrolux customer service, we cut off the power supply for one minute. When we turned the power back on, the display read PF (for power failure), but then it went completely black. Any advice?


Answers :

Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Suddenly, an error message appeared on the display of my Frigidaire gallery series dishwasher, model number GLD3450RDS0. On advice from Electrolux customer service, we cut off the power supply for one minute. When we turned the power back on, the display read PF (for power failure), but then it went completely black. Any advice?


... Frigidaire Dishwashers

See below Hi, Disconnect the Power Supply for Few Minutes, say 10 minutes and then Turn it ON. Do you see any Error Message on the Display? Do you see any Other Light Blinking? Have you tried to Press Cancel / Any other Button on the Touch Pad? Is it Working? Do you hear any Beep? Let me know, if needed further assistance. Hope i helped you. Thanks for using ' Fixya ' and have a nice day!! Comments: Apr 02, 2010 - Thanks for your response!! One more detail, i wanted to ask - Is that Wash Li


What's going on here? ... Dishwashers

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Dishwasher is just less than 1 year old. it doesn't respond to attempts to turn on. I turned off the power at the box and back on after 10 minutes. it worked. then the same problem returned. now it wont turn on at all. I checked all the connections I could and they seem fine. I know it is getting power. My guess is that something is wrong with the computer system. any ideas?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Maytag 24 in. MDBH950AW Built-in Dishwasher

There was some ordinary dishwashing liquid leftover on plates when i placed into dishwaher and this caused foam. The machine had a spanner appear on display and blinking light with a beeping noise. whenever I turn the machine off from the power button, it would after a 1 minute turn itself on again. with the blinking light, beeping noise and spanner picture on display. 1. how do i turn off completely 2. what does spanner mean and how do i resolve.


Hello &\015\012Welcome to FixYa\015\012\015\012Spanner\015\012indicates that there is excessive water in the unit, and instead of leaving it\015\012open you can take off the bottom front panel of the unit and clean the ... Dishwashers

Kenmore Ultra Wash Model 665.15801891 (Serial FJ3403697). This is in the USA. Unit will not run. Two lights are lit on the display panel and do not go off - 'Drying' and the #2 on 'Delay Hours'.rn I have turned off the power at the breaker box hoping it would reset. Once power is turned back on the Lock light comes on. I can clear that by pressing 'No Heat Dry' for 4 seconds but then the 2 lights mentioned above come on and do not go off. Any suggestions? Can you tell how old the unit is by t


Plase confirm if your model has the same front panel as the one shown in this manual.\015\012In that case try this sequence to reset the dis ... Kenmore 15899 Built-in Dishwasher

Dishwasher fault had leak,when opened bottom plate, could not see any obvious leak problem,hand dryed what componets i could. made sure no wires were loose then screwd back bottom plate,turn power back on but power button flashing continuously know,any advice plz


The flashing power button is a bad sign. You may have flooded the circuit board out or there may be a bad component as a result of the flood. Difficult to know from here.\015\012\015\012Most flooding on dish washers is caused by a faile ... Dishwashers

Hi - my Viking dishwasher has developed a problem where the pump runs continuously, whether the power switch is ON or OFF. After the power is turned ON, the troubleshooting guide indicates that there is too much water in the dishwasher. (One of the pot symbols on the display flashes continuously to show this indication.) I am unable to switch between programs, e.g., from quick rinse to pots & pans. I cleaned all the filters to no avail. I had to secure the circuit breaker in order to turn t


If you open the kick plate, you'll see the pan below the motor and check for leaks. The leaks will trigger the sensor to pump water out. Once you dry out the pan, the pump motor will stop and you should be able to reset the program. ... Viking DFUD042 Built-in Dishwasher

Kenmore Elite 13133K started to fill, the door was opened. Now it won't resume, drain or fill, the geen light is flashing. I turned the power supply off for 5 minutes and the problem still exists.


... Dishwashers

I have a hotpoint LFT04 dishwasher. Recently it tripped the power supply, and now when we start a cycle after a few minutes it stops and the lights on the power button and cycles 2 and 4 flash constantly. If the power button is turned off and the door closed, after a period of time it starts up again automatically. Any ideas appreciated.


... Dishwashers

Just turned the dishwasher on at the wall and tap after it's been sat off for a day. It's done one cycle (eco) and now doesn't seem to be doing anything but flashing. The two lights flashing are the power and eco lights. I have tried turning it off on the console but it turns itself back on and continues flashing. It sounds like it's whirring but I can't hear water. It did have a small leak when we first plumbed it in if that makes any difference?


... Hotpoint 18 in. DC27 Slim-Line Built-in Dishwasher

Hi . I have a Zanussi DE6965 which has started displaying the error message AL6 every now and then. When it stops and shows this the water has not pumped out. If you turn it off, leave for half an hour or so and turn back on it sometimes works fine to the end. Sometimes it stops again. Eventually after several stop starts it works through. Any advice what could be causing this? Thanks.


... Zanussi 24 in. DE6965 Built-in Dishwasher

Good day after the power is turned on to my brand new kudc03fvss dishwasher, nothing happens. have made sure that the power supply is ok and that the door is properly closed. there is 115 volts at the circuit board inside but nothing happens. no lights, no response to switch etc. just dead. need some advice


You said your getting 115 volts and that is across the power wire and its neutral not a power and ground.. i had a case like this last week and when i got there the unit had power if tested from black to ground but not from black and the white neutra ... Dishwashers

I have a Whirlpool Quiet Partner II. The normal light is blinking. If I press start it does nothing. If I press cancel, the cancel light blinks too. We turned off the power and let It sit for a few minutes. Powered it back on and same thing.


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Siemens Dishwasher. I'm not sure of the model but it is built in, has concealed controls and was purchased about 6 years ago at Best Buy. It sort of looks like the SL85. When started, it runs for a few minutes and then starts to make a horrible sound. ALmost a grinding sound but may also be like water trying to get through a small opening. The sound does not stop even after turning off the DW and even the power to it. Only turning off the water supply does it stop. Help?


... Siemens SL85A705UC 24 in. Built-in Dishwasher

We have a KitchenAid KEBC147KSDS06 24" conv. oven. After putting it through a clean cycle, I tried to preheat it to conv, bake @ 350 deg. The display comes up normally and the fan runs, but after 5 sec. the temp disappears from the display and 'Lo' appears in its place. The conv. fan continues to run but neither upper nor lower element heats. Following a suggestion, I tried to reset the oven by turning off its circuit breaker and powering back up, but it did not correct the problem.


It depends how long you had the self-clean function running. The oven is known to overheat and damage the thermostat during self-clean.\015\012\015\012See postings on some user forums.\015\012\015\012 ... KitchenAid 24 in. KUDS02SRSS Stainless Steel Built-in Dishwasher

Bosch D/W model # SHU9955UC. The drain motor will not stop running. Ran the reset sequence on the panel. Display reset to "0" minutes. Power cycled the D/W and when powered back on the drain motor started up again. What do I do ?


Hi ....This is a common problem. Remove the kick plate you will see the white base which also is a tray to collect leaks or backups. Reach your fingers over the top of tray and feel for water/wetness,if so safety switch has been activated and pump wi ... Bosch SHU9955UC Built-in Dishwasher

I have used my Bosch Dishwasher; [SGS6302 GB/07] [FD 7866 680062] for many years, with faultless performance. Last week, after loading it with Dinner plates, etc. I turned it ON and it declined to start, merely presenting me with an "F" on the display screen. Could find no solution in the (useless) instruction manual. So I guessed that "F" means;- a) Filter (blocked)? b) Fault condition. I've cleaned the filters, checked the power supply, water supply and drain hoses, but nothing seems to


Hello John,\015\012\015\012The "F" error in the display for Bosch dishwasher`s simply indicates, and I quote from my bosch service error code book, "water level or filling error, under fill, overfill or water in base ... Dishwashers

Kitchenaid model KUDIO1ILBL6 The lights for Heavy Cycle ,Normal Cycle and Cancel blinking at the sametime constantly. The tech sheet is missing and the unit is appox. 5years old.have shut power down for 5 minutes .When power turn back on only the Heavy Cycle light blinks costantly. Have Ohmed out the door switches and check adjustment OK. Checked board strips and plugs for good clean and tight connections OK. Thanks


Hi, You need to reset the unit by pushing the buttons. Push the heated wash/heated dry a few times. All the lights will light up and the dishwasher will continue its . Let ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I got this dishwasher from a friend that had mice chew the hoses and i was told that it worked perfect before the mice chewed it. I replaced the drain and fill hoses plus the power cord. when i put everything back together and power on I get F1 on the top drawer and the rotor rotates and the heater plate turns on. The botton drawer does nothing with no display. I checked all the wires with a meter and found good continuity thru every pin. I replaced the main filter board. I even switched the


Did the F1 error in the top drawer disappear after you replaced the mains filter board? ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Bosch shu43c05uc dishwasher regular and quick cycle run down to one minute and just keep on running . I have re set and turned circuit breaker off ond back on with no luck


... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

Child Lock light glows without pressing Energy Saver Dry button for four seconds. Cannot turn off by pressing Engery Saver Dry button for four seconds. Turning off main power and turning back on doesn't solve problem. But turning off main power for extented period, over night, and turning back on does fix proble for a very short period but Child Lock does come back on by itself. Is replacing the Console Assembly the only fix? Is there some button sequence to disable Child Lock altogher?


The mini manual for this dishwasher is located behind the kick plate. The mini-manual reveals that the child lock (called a control lock in the manual) can be disengaged by pressing and holding the air dry button for four seconds.or ene ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Kuds24se dead We have a 7 year-old KitchenAid kuds24se dishwasher. This morning it would not turn on. All lights on the control panel are out. I have verified the power and water supply. Any advice other than calling for a repairman? I am handy, have multipurpose electrical meter. Thx


Check the black and white wires that come from the plug. be careful but it sounds like a bad control.. ... KitchenAid KUDS24SE Built-in Dishwasher

No matter which cycle selection in pushed, the dishwasher only starts up in the "normal" 93 min cycle. If I try other cycle options, and persist, I get an ER message and the cycle stops prior to the soap powder door opening and never completes the cycle. Only with turning off power for several minutes and receiving the PF message, and resetting ONE TIME that message can I then select any cycle, at which time the machine "defaults" to the "normal" full cycle. If I do not disturb that cycle, it wi


Looks like you are having a good deal of problems with the dishwasher.\015\012\015\012It will be helpful if you provide the make and model no. of the dishwasher.\015\012\015\012At this stage I can speculate the controller (ass ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1550 seconds